Feasibility investigation of large-scale model suspended by cable-driven parallel robot in hypersonic wind tunnel test

Abstract

Cable-driven parallel robot is a special kind of robot, which is actuated by cables. It is already applied in the low speed wind tunnel to get aerodynamic measurement of aircraft model, and the aircraft pose could be adjusted by changing the cable length. Whether it can be used in hypersonic wind tunnel still needs further discussion. This paper presents the dynamics and aerodynamics analysis of a large-scale model supported by 6-DOF cable-driven parallel robot to investigate the feasibility of this special kind of suspension system in hypersonic wind tunnel. The description of this setup with a X-51A-like model is given, and then based on the system dynamic equations, aerodynamic force and stiffness matrix are derived. In the simulation, properties of dynamics and aerodynamics are mainly concerned. A typical shock tunnel with flow duration of about 100 milliseconds is taken as an example, and results show that the system is stable enough to meet the fundamental static wind tunnel test. From the cable tension variation under impact load and the sensitivity analysis, it is likely accessible to derive the aerodynamic forces. Compared with the sting suspension method, cable-driven parallel robot has the priority of higher inherent frequency and more flexible degrees. The interference to the flow field induced by cables is also preliminarily proved to be small by the CFD simulation, which can be acceptable and corrected. Researches conducted show the feasibility of cable-driven parallel robot’s application in hypersonic wind tunnel.

Keywords

Cable-driven parallel robot hypersonic wind tunnel dynamics aerodynamics stiffness interference

Get full access to this article

View all access options for this article.

References

Williams RL, Xin M and Bosscher P. Contour-crafting-cartesian cable robot system concepts: Workspace and stiffness comparisons. In: ASME, 32nd mechanisms and robotics conference, New York, USA, 3–6 August 2008.

Dallej T, Gouttefarde M, Andreff N, et al. Towards vision-based control of cable-driven parallel robots. In: Proceeding of the 2011 IEEE/RSJ international conference on intelligent robots and systems, 25–30 September 2011, San Francisco, CA, pp.2855-2860.

Duan

. A new design project of the line feed structure for large spherical radio telescope and its nonlinear dynamic analysis. Mechatronics 1999; 9: 53–64.

ONERA. SACSO, “suspension active pour essais en soufflerie,” http://www.onera.fr/dcsd/sacso /index. php (accessed 5 December 2008).

Bruckmann

Hiller

Schramm

. An active suspension system for simulation of ship maneuvers in wind tunnels, The Netherlands: Springer, 2010, pp. 537–544.

Xiao

Lin

Zheng

et al.

Model aerodynamic tests with a wire-driven parallel suspension system in low-speed wind tunnel. Chinese J Aeronaut 2010; 4: 393–400.

Zheng

Lin

Liu

. On wire-driven parallel suspension systems for static and dynamic derivatives of aircraft in low-speed wind tunnels. Acta Aeronau Tica et Astronautica Sinica 2009; 30: 1549–1554.

Ji YF and Lin Q. Dynamic test of SDM based on wire driven parallel suspension system in wind tunnel. In: The 10th civil experimental fliud dynamics conference, Shanghai, China, 8 May 2016.

Holden MS, Wadhams TP, MacLean M, et al. Experimental research and analysis in supersonic and hypervelocity flows in the LENS shock tunnels and expansion tunnel. In: 20th AIAA international space planes and hypersonic systems and technologies conference, Glasgow, Scotland, 6–9 July 2015, p.3660.

10.

Holden MS, Wadhams TP, MacLean M, et al. A review of basic research and development programs conducted in the lens facilities in hypervelocity flows. In: AIAA Paper, Nashville, Tennessee, USA, 2012.

11.

Hank JM, Murphy JS and Mutzman RC. The X-51A scramjet engine flight demonstration program. AIAA Paper, Dayton, Ohio, USA, April 28–May 1 2008.

12.

Wang XG, Ma SY and Lin Q. Hybrid pose/tension control based on stiffness optimization of cable-driven parallel mechanism in wind tunnel test. In: IEEE the 2nd International conference on control, automation and robotics, HongKong, 28–30 April 2016, pp.75-79.

13.

Jiang

Zhao

et al.

Investigating into techniques for extending the test duration of detonation-driven shock tunnels. Chin J Theor Appl Mech 2012; 44: 824–831.

14.

Wang

Zhao

et al.

Effective test time measurement research for high enthalpy shock tunnel. Acta Aeronautica et Astronautica Sinica 2015; 36: 3534–3539.

15.

Luo CT, Wang YP, Wang C, et al. A wave fitting method for the separation of aerodynamic signal from shock tunnels. LHD summer seminar, Shijiazhuang, China, 8–10 August 2013.