Calibration of a small size hexapod machine tool using coordinate measuring machine

Abstract

Hexapod machine tool (HMT) is a device designed for micro milling; however, the deviations of the HMT’s kinematic parameters due to manufacture and assembly errors can definitely affect its running accuracy. To identify the real kinematic parameters so as to improve the running accuracy of the HMT, a novel calibration test was performed on a bridge-type coordinate measuring machine. In the present research, a mathematical model was derived to present the relationship between pose errors and the errors of kinematic parameters of the HMT, the measurement method based on coordinate measuring machine was designed and a calibration experiment was carried out subsequently. The experimental results reveal that after calibration, both the position errors and orientation errors of the HMT decreased significantly, the symmetrical errors were improved as well. In addition, it is found that the running accuracy of the HMT is running direction dependent, which depends on the HTM’s structures. The present research provides researchers with a new and effective calibration method to improve the running accuracy of HMTs.

Keywords

Hexapod machine tools Stewart platform calibration measurement error compensation

Get full access to this article

View all access options for this article.

References

Stewart

. A platform with six degrees of freedom. Proc Inst Mech Engrs 1965; 18(1): 371–386.

Huang

Wang

. Kinematical calibration of a hybrid machine tool with regularization method. Int J Mach Tools Manuf 2011; 51(3): 210–220.

Ting

Jar

. Measurement and calibration for Stewart micromanipulation system. Precis Eng 2007; 31(3): 226–233.

Everett

. Forward calibration of closed-loop jointed manipulators. Int J Robot Res 1989; 8(4): 85–91.

Bennett

Hollerbach

. Autonomous calibration of single loop closed kinematic chains formed by manipulators with passive end point constraints. IEEE Trans Robot Autom 1991; 7(5): 597–606.

Renders

Rossignol

Becquet

. Kinematic calibration and geometrical parameter identification for robots. IEEE Trans Robot Autom 1991; 7(6): 721–732.

Everett LJ and Lin CY. Kinematic calibration of manipulators with closed loop actuated joints. In: Proceedings of IEEE international conference on robotics and automation, Philadelphia, PA, 1986, pp.792–797.

Zhuang H and Liu L. Self-calibration of a class of parallel manipulators. In: Proceedings of IEEE international conference on robotics & automation, Minneapolis, MN, USA, 1996, pp.994–999.

Zhuang

. Self-calibration of parallel mechanisms with a case study on Stewart platforms. IEEE Trans Robot Autom 1997; 13(3): 387–397.

10.

Chiu

Perng

. Self-calibration of a general hexapod manipulator using cylinder constraints. Int J Mach Tools Manuf 2003; 43(10): 1051–1066.

11.

Chiu

Perng

. Self-calibration of a general hexapod manipulator with enhanced precision in 5-DOF motions. Mech Mach Theory 2004; 39(1): 1–23.

12.

Ren

Feng

. A new calibration method for parallel kinematics machine tools using orientation constraint. Int J Mach Tools Manuf 2009; 49(9): 708–721.

13.

Zhuang H, Masory O and Yan JH. Kinematic calibration of a Stewart platform using pose measurements obtained by a single theodolite. In: Proceedings of IEEE/RSJ international conference on intelligent robots and systems. Human Robot Interaction and Cooperative Robots. Pittsburgh, PA, USA, 1995, pp.329–334.

14.

Gao M, Li TM and Yin WS. Calibration method and experiment of Stewart platform using a laser tracker. In: Proceedings of IEEE international conference on systems, man and cybernetics, Washington, USA, 2003, pp.2797–2802.

15.

Dallej T, Hadi-Abdelkader H, Andreff N, et al. Kinematic calibration of a Gough-Stewart platform using an omnidirectional camera. In: Proceedings of IEEE/RSJ international conference on intelligent robots and systems, Beijing, 2006, pp.4666–4671.

16.

Nategh

Agheli

. A total solution to kinematic calibration of hexapod machine tools with a minimum number of measurement configurations and superior accuracies. Int J Mach Tools Manuf 2009; 49(15): 1155–1164.

17.

Gao

Tang

. Estimates of identification result disturbances in parallel mechanism calibration. Tsinghua Sci Technol 2006; 11(1): 80–87.

18.

Abtahi

Pendar

Alasty

. Experimental kinematic calibration of parallel manipulators using a relative position error measurement system. Robot Comput-Integr Manuf 2010; 26(6): 799–804.

19.

Meng

Zhuang

. Autonomous robot calibration using vision technology. Robot Comput-Integr Manuf 2007; 23(4): 436–446.

20.

Daney

Andreff

Chabert

. Interval method for calibration of parallel robots: Vision-based experiments. Mech Mach Theory 2006; 41: 929–944.

21.

Patel Amit

Ehmann Kornel

. Calibration of a hexapod machine tool using a redundant leg. Int J Mach Tools Manuf 2000; 40(4): 489–512.

22.

Axinte

Allen

Anderson

. Free-leg hexapod: A novel approach of using parallel kinematic platforms for developing miniature machine tools for special purpose operations. CIRP Ann Manuf Technol 2011; 60(1): 395–398.

23.

Harib

Sharif Ullah

AMM

Hammami

. A hexapod-based machine tool with hybrid structure: Kinematic analysis and trajectory planning. Int J Mach Tools Manuf 2007; 47(9): 1426–1432.

24.

Rahman

Heikkala

Lappalainen

. Modeling, measurement and error compensation of multi-axis machine tools. Part I: Theory. Int J Mach Tools Manuf 2000; 40(10): 1535–1546.

25.

Wang J and Masory O. On the accuracy of a Stewart platform. I. The effect of manufacturing tolerances. In: Proceedings of the IEEE international conference on robotics and automation, Atlanta, GA, USA, 1993, pp.114–120.