Thin-walled aluminum tubes are widely used for different structural purposes, and therefore, the development of new methods for strengthening these elements is critical. This matter is especially true for aluminum alloys 6xxx since their maximum strengths projected through peak-aging are considerably lower than the similar strength of other wrought aluminum alloys like 2xxx and 7xxx. Although different works have proposed the imposition of severe plastic deformation for strengthening of 6xxx alloys, the application of this method for thin-walled tubes has been less studied due to the complexities of the severe plastic deformation processing of thin-walled tubes. In this study, the manufacturing of high-strength thin-walled aluminum 6063 tubes through the imposition of a new severe plastic deformation process and a subsequent post-aging treatment at two different temperatures is studied. For this purpose, the tension test is applied to measure the strength variation. Also, the electron backscattering diffraction equipped with scanning electron microscopy and the X-ray diffraction experiments are applied to investigate the microstructural evolution. Results show that the proposed approach can be successfully applied to the manufacturing of high-strength thin-walled aluminum 6063 tubes. Also, the strengthening effect of this procedure is attributed to an increase in the dislocation density and refinement of grains during the imposition of severe plastic deformation and an appearance of finer precipitates during the peak-aging treatment.
SakaiTBelyakovAKaibyshevR, et al. Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions. Prog Mater Sci2014; 60: 130–207.
2.
EstrinYVinogradovA.Extreme grain refinement by severe plastic deformation: A wealth of challenging science. Acta Mater2013; 61: 782–817.
3.
Nemati ChariRMollaei DarianiBFallahi ArezodarA. Numerical and experimental studies on deformation behavior of 5083 aluminum alloy strips in equal channel angular rolling. Proc IMechE, Part B: J Engineering Manufacture2018; 232: 1031–1043.
4.
Nazari TijiSAsgariAGholipourH, et al. Modeling of equal channel forward extrusion force using response surface approach. Proc IMechE, Part B: J Engineering Manufacture2018; 232: 713–719.
5.
VinogradovAEstrinY.Analytical and numerical approaches to modelling severe plastic deformation. Prog Mater Sci2018; 95: 172–242.
6.
TothLSChenCPougisA, et al. High pressure tube twisting for producing ultra fine grained materials: A Review. Mater Trans2019; 60: 1177–1191.
7.
MohebbiMSAkbarzadehA.Accumulative spin-bonding (ASB) as a novel SPD process for fabrication of nanostructured tubes. Mater Sci Eng A2010; 528: 180–188.
8.
FarshidiMKazeminezhadM.The effects of die geometry in tube channel pressing: Severe plastic deformation. Proc IMechE, Part L: J Materials Design and Applications2016; 230: 263–272.
9.
FarshidiMH.Optimization of die geometry for tube channel pressing. Iran J Mater Form2018; 5: 26–35.
10.
FarajiGAbriniaKMashhadiMM, et al. An upper-bound analysis for frictionless TCAP process. Arch Appl Mech2013; 83: 483–493.
11.
AbdolvandHSohrabiHFarajiG, et al. A novel combined severe plastic deformation method for producing thin-walled ultrafine grained cylindrical tubes. Mater Lett2015; 143: 167–171.
12.
TorabzadehHFarajiGZalnezhadE.Cyclic flaring and sinking (CFS) as a new severe plastic deformation method for thin-walled cylindrical tubes. Trans Indian Ins Metals2016; 69: 1217–1222.
13.
ShapourganOFarajiG.Rubber pad tube straining as a new severe plastic deformation method for thin-walled cylindrical tubes. Proc IMechE, Part B: J Engineering Manufacture2016; 230(10): 1845–1854.
14.
PogatscherSAntrekowitschHLeitnerH, et al. Mechanisms controlling the artificial aging of Al–Mg–Si Alloys. Acta Mater2011; 59: 3352–3363.
15.
TanEKibarAAGürCH.Mechanical and microstructural characterization of 6061 aluminum alloy strips severely deformed by dissimilar channel angular pressing. Mater Charact2011; 62: 391–397.
16.
DavisJR. Selection and application of aluminum alloys. In: DavisJR (ed.) ASM Specialty Handbook: aluminum and aluminum Alloys. Materials Park: ASM International, 1993, pp.59–180, 1st ed.
17.
HilditchTAtwellDEastonM, et al. Performance of wrought aluminium and magnesium alloy tubes in three-point bending. Mater Des2009; 30: 2316–2322.
18.
AydınHBayramAUğuzA, et al. Tensile properties of friction stir welded joints of 2024 aluminum alloys in different heat-treated-state. Mater Des2009; 30: 2211–2221.
19.
AhmadiFFarzinM.Investigation of a new route for equal channel angular pressing process using three-dimensional finite element method. Proc IMechE, Part B: J Engineering Manufacture2014; 228: 765–774.
20.
BhattacharyaABatishA.Effect of process variables on microhardness, grain size and strain during machining of various die steels with powder-mixed electric-discharge machining using dummy treated experimental design. Proc IMechE, Part B: J Engineering Manufacture2012; 226(7): 1192–1204.
21.
KoizumiTKurodaM.Grain size effects in aluminum processed by severe plastic deformation. Mater Sci Eng A2018; 710: 300–308.
22.
FarshidiMHRifaiMMiyamotoH.Microstructure evolution of a recycled Al–Fe–Si–Cu alloy processed by tube channel pressing. Int J Miner Metall Mater2018; 25: 1166–1172.
23.
SabirovIMurashkinMYValievRZ.Nanostructured aluminium alloys produced by severe plastic deformation: New horizons in development. Mater Sci Eng A2013; 560: 1–24.
24.
HuJZhangWFuD, et al. Improvement of the mechanical properties of Al–Mg–Si alloys with nano-scale precipitates after repetitive continuous extrusion forming and T8 tempering. J Mater Res Technol2019; 8: 5950–5960.
25.
BabuVShanmugavelBPPadmanabhanKA.Effects of processing temperature and number of passes on the microstructure and mechanical properties of AA 6063 processed by cyclic expansion extrusion. Arch Civil Mech Eng2021; 21. Article No. 38.
26.
VendraSSLGoelSKumarN, et al. A study on fracture toughness and strain rate sensitivity of severely deformed Al 6063 alloys processed by multiaxial forging and rolling at cryogenic temperature. Mater Sci Eng A2017; 686: 82–92.
27.
KhelfaTRekikMAMuñoz-BolañosJA, et al. Microstructure and strengthening mechanisms in an Al-Mg-Si alloy processed by equal channel angular pressing (ECAP). Int J Adv Manuf Technol2018; 95: 1165–1177.
28.
FlittaISheppardT.Nature of friction in extrusion process and its effect on material flow. Mater Sci Technol2003; 19: 837–846.
29.
WiderøeFWeloT.Conditions for sticking friction between aluminium alloy AA6060 and tool steel in hot forming. Key Eng Mater2011; 491: 121–128.
30.
Al-HamdanyNSalihMZPalkowskiH, et al. Tube drawing with tilted die: texture, dislocation density and mechanical properties. Metals2021; 11: 638.
31.
ChoJHParkSJChoiSH, et al. Deformation texture of cold drawn Al6063 tube. Mater Sci Forum2002; 408-412: 565–570.
32.
WangSWChenYSongHW, et al. Investigation of texture transformation paths in copper tube during floating plug drawing process. Int J Mater Forming2021; 14: 563–575.
33.
FarshidiMHMiyamotoH.Texture evolution of a dilute aluminum alloy subjected to tube channel pressing. Mater Res Express2019; 6: 026564
34.
RovenHJLiuMWerenskioldJC.Dynamic precipitation during severe plastic deformation of an Al–Mg–Si aluminium alloy. Mater Sci Eng A2008; 483–484: 54–58.
35.
PanigrahiSKJayaganthanRPancholiV, et al. A DSC study on the precipitation kinetics of cryorolled Al 6063 alloy. Mater Chem Phys2010; 122: 188–193.
36.
GubiczaJSchillerIChinhNQ, et al. The effect of severe plastic deformation on precipitation in supersaturated Al–Zn–Mg alloys. Mater Sci Eng A2007; 460–461: 77–85.
37.
HuangWLiuZLinM, et al. Reprecipitation behavior in Al–Cu binary alloy after severe plastic deformation-induced dissolution of θ′ particles. Mater Sci Eng A2012; 546: 26–33.
38.
FujdaMMatvijaMKvakajT, et al. Structure and properties of the AlMgSi alloys after ECAP and post-ECAP ageing. Mater Tech2012; 46: 465–469.
39.
SalcedoDLuisCJLeónJ, et al. Simulation and analysis of isothermal forging of AA6063 obtained from material processed by equal channel angular pressing severe plastic deformation. Proc IMechE, Part B: J Engineering Manufacture2015; 229: 727–743.
40.
PanigrahiSKJayaganthanR.Development of ultrafine grained Al–Mg–Si alloy with enhanced strength and ductility. J Alloys Comp2009; 470: 285–288.
41.
EstrinY.Dislocation density related constitutive modeling. In: KrauszASKrauszK (ed.) Unified constitutive laws of plastic deformation. Academic Press, San Diego, 1996, pp.69–106.
42.
BuiQHPhamXTFafardM.Modelling of microstructure effects on the mechanical behavior of aluminium tubes drawn with different reduction areas. Int J Plast2013; 50: 127–145.
ChinhNQGubiczaJCzeppeT, et al. Developing a strategy for the processing of age-hardenable alloys by ECAP at room temperature. Mater Sci Eng A2009; 516: 248–252.
