Residual stresses can meaningfully influence on the operation of a part. They are almost created by all fabrication processes. In this study, slitting method was used to obtain the residual stress profile through the thickness of equal-channel angular rolled aluminum strips. Furthermore, uncertainty analysis of the measured residual stresses was performed. The measurement and model uncertainties were considered in the uncertainty analysis, and the effect of each one on the total uncertainty was investigated. Besides, to study the through-depth residual stress distribution numerically, finite element simulation of equal-channel angular rolling process in route C was done. In route C, the strip should be rotated around the longitudinal axis by 180° after each successive pass. The results showed the important role of both measurement and model uncertainties in the calculation of total uncertainty. The maximum tensile residual stresses of the control, 1-pass and 2-pass samples were 7.59, 64.4 and 85.11 MPa, respectively, and the root mean square total uncertainty of them were 1.47, 2.43 and 5.12 MPa, respectively. There was a good agreement between experimental and numerical results.
PrimeMB. Residual stress measurement by successive extension of a slot: the crack compliance method. Appl Mech Rev1999; 52(2): 75–96.
5.
MilanMTBose FilhoWWTarpaniJR. Residual stress evaluation of AA2024-T3 friction stir welded joints. J Mater Eng Perform2007; 16: 86–92.
6.
VaidyanathanSFinnieI. Determination of residual stresses from stress intensity factor measurements. J Basic Eng1971; 93: 242–246.
7.
MahmoudiAHSheikhpourMRHeydarianS. A novel cutting strategy for measuring two components of residual stresses using slitting method. Exp Mech2014; 54(7): 1237–1246.
8.
ShokriehMMAkbariS. Isolation of residual shear stress effects in slitting measurement of residual normal stress in laminated composites. J Compos Mater2014; 48(7): 791–798.
9.
DongYBShaoWZJiangJT. Minimization of residual stress in an Al-Cu alloy forged plate by different heat treatments. J Mater Eng Perform2015; 24(6): 2256–2265.
10.
Urriolagoitia-SosaGDurodolaJFFellowsNA. Effect of strain hardening on residual stress distribution in beams determined using the crack compliance method. J Strain Anal Eng2007; 42(2): 115–121.
11.
SedighiMJoudakiJKotobiM. Uncertainty of residual stresses analysis in slitting method: a case study of roll bending process. J Strain Anal Eng2015; 50(5): 335–343.
12.
DeWaldATHillMR. Repeatability of incremental hole drilling and slitting method residual stress measurements. In: MRossiMSassoNConnesson. (eds) Residual stress, thermomechanics & infrared imaging, hybrid techniques and inverse problems, vol. 8 (conference proceedings of the society for experimental mechanics series). Cham: Springer International Publishing, 2014, pp.113–118.
13.
PrimeMBCraneDL. Slitting method measurement of residual stress profiles, including stress discontinuities, in layered specimens. In: MRossiMSassoNConnesson. (eds) Residual stress, thermomechanics & infrared imaging, hybrid techniques and inverse problems, vol. 8 (conference proceedings of the society for experimental mechanics series). Cham: Springer International Publishing, 2014, pp.93–102.
14.
AzushimaAKoppRKorhonenA. Severe plastic deformation (SPD) processes for metals. CIRP Ann: Manuf Techn2008; 57: 716–735.
15.
KumarSSRaghuT. Strain path effects on microstructural evolution and mechanical behaviour of constrained groove pressed aluminium sheets. Mater Design2015; 88: 799–809.
16.
ShaeriMHDjavanroodiFSedighiM. Effect of copper tube casing on strain distribution and mechanical properties of Al-7075 alloy processed by equal channel angular pressing. J Strain Anal Eng2013; 48(8): 512–521.
17.
EbrahimiMRajabifarBDjavanroodiF. New approaches to optimize strain behavior of Al6082 during equal channel angular pressing. J Strain Anal Eng2013; 48(6): 395–404.
18.
FarshidiMHKazeminezhadM. The effects of die geometry in tube channel pressing: severe plastic deformation. Proc IMechE, Part L: J Materials: Design and Applications2016; 230(1): 263–272.
19.
JafarzadehHAbriniaK. Computation on continuous grain refinement in AA1050 aluminum during repetitive tube expansion and shrinking technique. Proc IMechE, Part L: J Materials: Design and Applications. Epub ahead of print 31December2015. DOI: 10.1177/1464420715625086.
20.
LeeJCSeokHKHanJH. Controlling the textures of the metal strips via the continuous confined strip shearing (C2S2) process. Mater Res Bull2001; 36(5): 997–1004.
21.
HabibiAKetabchiMEskandarzadehM. Nano-grained pure copper with high-strength and high-conductivity produced by equal channel angular rolling process. J Mater Process Tech2011; 211: 1085–1090.
22.
ChengYQChenZHXiaWJ. Drawability of AZ31 magnesium alloy sheet produced by equal channel angular rolling at room temperature. Mater Charact2007; 58: 617–622.
23.
HassaniFZKetabchiM. Nano grained AZ31 alloy achieved by equal channel angular rolling process. Mater Sci Eng A: Struct2011; 528: 6426–6431.
24.
AzimiATutunchilarSFarajiG. Mechanical properties and microstructural evolution during multi-pass ECAR of Al 1100–O alloy. Mater Design2012; 42: 388–394.
25.
MahmoodiMSedighiMTannerDA. Investigation of through thickness residual stress distribution in equal channel angular rolled Al 5083 alloy by layer removal technique and X-ray diffraction. Mater Design2012; 40: 516–520.
26.
HonarpishehMHaghighatEKotobiM. Investigation of residual stress and mechanical properties of equal channel angular rolled St12 strips. Proc IMechE, Part L: J Materials: Design and Applications. Epub ahead of print 1June2016. DOI: 10.1177/1464420716652436.
27.
DeWaldATRankinJEHillMR. An improved cutting plan for removing laser amplifier slabs from Yb:S-FAP single crystals using residual stress measurement and finite element modeling. J Cryst Growth2004; 265: 627–641.
28.
LeeMJHillMR. Effect of strain gage length when determining residual stress by slitting. J Eng Mater2007; 129: 143–150.
29.
PrimeMBHillMR. Uncertainty analysis, model error, and order selection for series-expanded, residual stress inverse solutions. J Eng Mater2006; 128(2): 175–185.
30.
PrimeMBPagliaroP. Uncertainty, model error, and improving the accuracy of residual stress inverse solutions. In: Proceedings of the 2006 SEM annual conference and exposition on experimental and applied mechanics, USA, 4–7 June 2006.
31.
ASTM E8/E8M-09 standard test methods for tension testing of metallic materials. West Conshohocken, PA: ASTM International, 2009.
