Laser welding with beam wobbling was employed to weld X70 pipeline steel. The influence of beam wobbling on weld surface morphology, fusion zone microstructure, and microhardness was investigated. The formation of spatter was suppressed by beam wobbling using a beam with higher energy density. At a welding speed of 1.0 m min−1, the weld metal produced with a circular laser wobble pattern contained more martensite but less ferrite, compared to that of static spot welded joint. The presence of more martensite led to the increase in fusion zone hardness. A softened region was found in the inter-critical heat-affected zone. The hardness of the softened region could be improved by increasing the welding speed (from 1.0 to 1.5 m min−1).
NishiokaK, IchikawaK.Progress in thermomechanical control of steel plates and their commercialization. Sci Technol Adv Mater. 2012; 13:1–20.
2.
ReichertJM.Structure and properties of complex transformation products in Nb/Mo-microalloyed steels [dissertation]. Vancouver (BC): The University of British Columbia; 2016.
3.
YangH, SunY, TanC, Influence of Al–Si coating on microstructure and mechanical properties of fiber laser welded and then press-hardened 22MnB5 steel. Mater Sci Eng A. 2020; 794:139918.
4.
ZhaoX, TanC, XiaoL, Effect of the Ni coating thickness on laser welding-brazing of Mg/steel. J Alloys Compd. 2018; 769:1042–1058.
5.
DawesCT.Laser welding: a practical guide. Cambridge: Abington; 1992.
6.
KatayamaS.Handbook of laser welding technologies: introduction: fundamentals of laser welding. Cambridge: Woodhead Publishing Limited; 2013; p. 3–16.
7.
HaoK, LiG, GaoM, Weld formation mechanism of fiber laser oscillating welding of austenitic stainless steel. J Mater Process Technol. 2015; 225:77–83.
8.
MatsunawaA, MizutaniM, KatayamaS, Porosity formation mechanism and its prevention in laser welding. Weld Int. 2003; 17:431–437.
9.
LiJ, SunQ, LiuY, Melt flow and microstructural characteristics in beam oscillation superimposed laser welding of 304 stainless steel. J Manuf Process. 2020; 50:629–637.
10.
RubbenK, MohrbacherH, LeirmanE.Advantages of using an oscillating laser beam for the production of tailed blanks. Proc. SPIE 3097, Lasers Mater Process. 1997; 3097: 228–241.
JiangM, TaoW, ChenY.Laser welding under vacuum: a review. Appl Sci. 2017; 7:1–17.
13.
ShenJ, LiB, HuS, Comparison of single-beam and dual-beam laser welding of Ti–22Al–25Nb/TA15 dissimilar titanium alloys. Opt Laser Technol. 2017; 93:118–126.
14.
KuryntsevVS, GilmutdinovAK.Heat treatment of welded joints of steel 0.3C-1Cr-1Si produced by high-power fiber lasers. Opt Laser Technol. 2015; 74:125–131.
15.
ZhangC, YuY, ChenC, Suppressing porosity of a laser keyhole welded Al-6Mg alloy via beam oscillation. J Mater Process Technol. 2020; 278:116382.
16.
LiuT, MuZ, HuR, Sinusoidal oscillating laser welding of 7075 aluminum alloy: hydrodynamics, porosity formation and optimization. Int J Heat Mass Transf. 2019; 140:346–358.
17.
KuryntsevVS, GilmutdinovAK.The effect of laser beam wobbling mode in welding process for structural steels. Int J Adv Manuf Technol. 2015; 81:1683–1691.
18.
GrünenwaldS, UntA, SalminenA.Investigation of the influence of welding parameters on the weld geometry when welding structural steel with oscillated high-power laser beam. Procedia CIRP. 2018; 74:461–465.
19.
WangL, GaoM, ZhangC, Effect of beam oscillating pattern on weld characterization of laser welding of AA6061-T6 aluminum alloy. Mater Des. 2016; 108:707–717.
20.
JiangZ, ChenX, LiH, Grain refinement and laser energy distribution during laser oscillating welding of Invar alloy. Mater Des. 2020; 186:108195.
21.
LiS, ChenG, ZhouC.Effects of welding parameters on weld geometry during high-power laser welding of thick plate. Int J Adv Manuf Technol. 2015; 79:177–182.
22.
LiS, ChenG, KatayamaS, Relationship between spatter formation and dynamic molten pool during high-power deep-penetration laser welding. Appl Surf Sci. 2014; 303:481–488.
23.
ZouJ, ZhuB, ZhangG, Power density effect on the laser beam-induced eruption of spatters in fiber laser keyhole welding. Opt Laser Technol. 2022; 147:107651.
24.
KouS.Welding metallurgy. New York: Wiley; 1987.
25.
LeiZ, TanC, ChenY, Microstructure and mechanical properties of fiber laser-metal active gas hybrid weld of X80 pipeline steel. J Press Vessel Technol Trans ASME. 2013; 135:1–7.
26.
MohammadijooM, VallotonJ, CollinsL, Characterization of martensite-austenite constituents and micro-hardness in intercritical reheated and coarse-grained heat affected zones of API X70 HSLA steel. Mater Charact. 2018; 142:321–331.
27.
DerevyaginaLS, GordienkoAI, Orishich AM, Microstructure of intercritical heat affected zone and toughness of microalloyed steel laser welds. Mater Sci Eng A. 2020; 770:138522.
28.
LeeSG, KimB, KimWG, Effects of Mo addition on crack tip opening displacement (CTOD) in heat affected zones (HAZs) of high-strength low-alloy (HSLA) steels. Sci Rep. 2019; 9:1–12.
29.
FarichildD, BangaruN, KooJ, A study concerning intercritical HAZ microstructure and toughness in HSLA steels. Weld J. 1991; 70:321.
30.
HudaN.Effect of martensite-austenite (MA) on mechanical properties of X80 Linepipe Steel [dissertation]. Waterloo (ON): University of Waterloo; 2018.
31.
MoeinifarS, KokabiAH, Madaah HosseiniHR.Influence of peak temperature during simulation and real thermal cycles on microstructure and fracture properties of the reheated zones. Mater Des. 2010; 31:2948–2955.
32.
WangSC, YangJR.Effects of chemical composition, rolling and cooling conditions on the amount of martensite/austenite (M/A) constituent formation in low carbon bainitic steels. Mater Sci Eng A. 1992; 154:43–49.
33.
HudaN, MidawiARH, GianettoJ, Influence of martensite-austenite (MA) on impact toughness of X80 line pipe steels. Mater Sci Eng A. 2016; 662:481–491.
34.
HaoK, WangH, GaoM, Laser welding of AZ31B magnesium alloy with beam oscillation. J Mater Res Technol. 2019; 8:3044–3053.
35.
LiS, MiG, WangC.A study on laser beam oscillating welding characteristics for the 5083 aluminum alloy: morphology, microstructure and mechanical properties. J Manuf Process. 2020; 53:12–20.
36.
StJohnDH, PrasadA, EastonMA, The contribution of constitutional supercooling to nucleation and grain formation. Metall Mater Trans A Phys Metall Mater Sci. 2015; 46:4868–4885.
37.
LiL, GongJ, XiaH, Influence of scan paths on flow dynamics and weld formations during oscillating laser welding of 5A06 aluminum alloy. J Mater Res Technol. 2021; 11:19–32.
