The present work demonstrates a two-step method to deposit copper over ABS plastic using electric arc thermal spray means. The energy dispersive spectroscopy confirmed the deposition of copper metal. The adhesive strength demonstrates an increasing trend as the stand-off distance increases from 11 to 17 cm, and decreases as the stand-off distance further increases till 23 cm. For surface roughness, porosity and coating thickness, an increasing trend was noticeable as the stand-off distance increases from 11 to 15 cm, and then assumes a decreasing trend till 23 cm of stand-off distance. The surface residual stress demonstrates decreasing course as the stand-off distance increases from 11 to 23 cm. Different factors engaged during the deposition of molten metal droplet on the ABS substrate such as thermal softening, oxide content, particle velocity and cooling rate dictated the characteristic outcome such as adhesive strength, roughness, porosity coating thickness and surface residual stress.
MittalKL, SuskoJR.Metallized plastics 1: fundamental and applied aspects. New York
: Springer US; 1989.
2.
EqubalA, SoodAK.Metallization on FDM parts using the chemical deposition technique. Coatings. 2014;4:574–586. doi: 10.3390/coatings4030574
3.
MittalKL, SuskoJR.Metallized plastics 3: fundamental and applied aspects. New York
: Springer US; 1992.
4.
DomenechSC, LimaE, DragoV, Electroless plating of nickel-phosphorous on surface-modified poly(ethylene terephthalate) films. Appl Surf Sci. 2003;220(1–4):238–250. doi: 10.1016/S0169-4332(03)00815-8
5.
KulkarniMV, ElangovanK, ReddyKH, Tribological behaviours of ABS and PA6 polymermetal sliding combinations under dry friction, water absorbed and electroplated conditions. J Eng Sci Technol. 2016;11(1):68–84.
6.
OliveraS, MuralidharaHB, VenkateshK, Plating on acrylonitrile-butadiene-styrene (ABS) plastic: a review. J Mater Sci. 2016;51(8):3657–3674. doi: 10.1007/s10853-015-9668-7
7.
BazzaouiM, MartinsJI, BazzaouiEA, A simple method for acrylonitrile butadiene styrene metallization. Surf Coat Technol. 2013;224:71–76. doi: 10.1016/j.surfcoat.2013.02.050
8.
TangX, CaoM, BiC, Research on a new surface activation process for electroless plating on ABS plastic. Mater Lett. 2008;62(6–7):1089–1091. doi: 10.1016/j.matlet.2007.07.055
9.
OnoS, NaitohK, OsakaT.Initial propagation stage of direct copper plating on non-conducting substrates. Electrochim Acta. 1999;44(21–22):3697–3705. doi: 10.1016/S0013-4686(99)00073-0
10.
GonzalezR, AshrafizadehH, LoperaA, A Review of thermal spray metallization of polymer-based structures. J Therm Spray Technol. 2016;25(5):897–919. doi: 10.1007/s11666-016-0415-7
11.
TomaFL, AnnegretP, BergerLM, Demands, potentials, and economic aspects of thermal spraying with suspensions: a critical review. J Therm Spray Technol. 2015;24(7):1143–1152. doi: 10.1007/s11666-015-0274-7
12.
SalavatiS, CoyleTW, MostaghimiJ.Twin wire arc spray process modification for production of porous metallic coatings. Surf Coat Technol. 2016;286:16–24. doi: 10.1016/j.surfcoat.2015.12.004
NourouziS, AzizpourMJ, SalimijaziHR.Parametric study of residual stresses in HVOF thermally sprayed WC – 12Co coatings. Mater Manuf Process. 2014;29:1117–1125. doi: 10.1080/10426914.2014.921696
15.
MantryS, MishraBK, ChakrabortyM.Parametric appraisal of process parameters for adhesion of plasma sprayed nanostructured YSZ coatings using taguchi experimental design. Sci World J. 2013;2013:1–8. doi: 10.1155/2013/527491
16.
GoyalT, WaliaRS, SidhuTS.Surface roughness optimization of cold-sprayed coatings using taguchi method. Int J Adv Manuf Technol. 2011;60(5–8):611–623. doi: 10.1007/s00170-011-3642-6
JandinG, LiaoH, FengZQ, Correlations between operating conditions, microstructure and mechanical properties of twin wire arc sprayed steel coatings. Mater Sci Eng A. 2003;349(1–2):298–305. doi: 10.1016/S0921-5093(02)00767-0
19.
OksaM, TurunenE, SuhonenT, Optimization and characterization of high velocity Oxy-fuel sprayed coatings: techniques, materials, and applications. Coatings. 2011;1:17–52. doi: 10.3390/coatings1010017
20.
LiuG, RozniatowskiK, KurzydłowskiKJ.Quantitative characteristics of FeCrAl films deposited by arc and high-velocity arc spraying. Mater Charact. 2001;46(2–3):99–104. doi: 10.1016/S1044-5803(01)00108-5
21.
SoodAK, OhdarRK, MahapatraSS.Parametric appraisal of mechanical property of fused deposition modelling processed parts. Materials and Design. 2016;31(1):287–295. doi: 10.1016/j.matdes.2009.06.016
22.
HuonnicN, AbdelghaniM, MertinyP, Deposition and characterization of fl ame-sprayed aluminum on cured glass and basalt fi ber-reinforced epoxy tubes. Surf Coat Technol. 2010;205(3):867–873. doi: 10.1016/j.surfcoat.2010.08.029
23.
GonzalezR, McDonaldA, MertinyP.Effect of flame-sprayed Al-12Si coatings on the failure behaviour of pressurized fibre-reinforced composite tubes. Polym Test. 2013;32(8):1522–1528. doi: 10.1016/j.polymertesting.2013.10.002
24.
WangY, LiC, OhmoriA.Influence of substrate roughness on the bonding mechanisms of high velocity oxy-fuel sprayed coatings. Thin Solid Films. 2005;485(1):141–147. doi: 10.1016/j.tsf.2005.03.024
25.
FunkW, GoebeF.Metallic coating for carbon fiber reinforced metallic coating for carbon fiber reinforced polymer matrix composite substrate. Int J Chem, Mol, Nucl, Mater Metal Eng. 2016;10(1):64–69.
26.
SarikayaO.Effect of some parameters on microstructure and hardness of alumina coatings prepared by the air plasma spraying process. Surf Coat Technol. 2005;190(2–3):388–393. doi: 10.1016/j.surfcoat.2004.02.007
27.
GassotH, JunqueraT, JiV, Comparative study of mechanical properties and residual stress distributions of copper coatings obtained by different thermal spray processes. Surf Eng. 2017;17(4):317–322. doi: 10.1179/026708401101517944
28.
ASTM C633-13. Standard test method for adhesion or cohesion strength of thermal spray coatings. Conshohocken (PA
): ASTM International; 2017.
