Owing to external disturbances, parameter uncertainty, and measurement noise, it has been a challenging task to develop an appropriate controller for the automated clutch system. This paper proposes a new method for electromechanical clutch position control systems. First, a non-linear dynamic model for the screw-nut actuator associated with a clutch is derived, and then a dynamic sliding-mode controller with fuzzy adaptive tuning is developed. The fuzzy adaptive tuning arithmetic is used to improve the robustness and stability of the controller. At the same time, the chattering phenomenon is alleviated by adopting the proposed controller. Based on dSPACE and MATLAB—Simulink, the rapid control prototyping of the automated clutch is used as a method to demonstrate the efficiency and robustness of the proposed algorithm.
ShenS. W.WuC. Q.‘An expert fuzzy control of automatic mechanical transmission clutch.’ SAE paper 1999–01-2814, 1999.
2.
HibinoR.OsawaM.YamadaM.‘H∞ control design for torque-converter-clutch slip system.’In Proceedings of the 35th Conference on Decision and control, Kobe, Japan, 1996, pp. 1797–1802 (IEEE, New York).
3.
GlielmoL.IannelliL.VaccaV.VascaF.‘Gearshift control for automated manual transmissions.’IEEE/ASME Trans. Mechatronics11 (1) (2006): 17–26
4.
HornJ.BambergerJ.MichauP.‘Flatness-based clutch control for automated manual transmissions.’Control Engng Practice11 (2003): 1353–1359
5.
SlickerJ. M.LohR. N. K.‘Design of robust vehicle launch control system.’IEEE Trans. Control Systems Technol.4 (4) (1996): 326–335
6.
ZanasiR.ViscontiA.‘Dynamic modeling and control of a car transmission system.’In Proceedings of the 2001 IEEE/ASME International Conference on Advanced intelligent mechatronics, Como, Italy, Italy, 2001, pp. 416–421 (IEEE/ASME, New York).
7.
SanadaK.KitagawaA.‘A study of two-degree-of-freedom control of rotating speed in an automatic transmission, considering modeling errors of a hydraulic system.’Control Engng Practice6 (1998): 1125–1132
8.
DavidJ.NatarajanN.‘Design of an optimal clutch controller for commercial trucks.’ In Proceedings of the 2005 American Control Conference, Portland, Oregon, USA, 2005, pp. 1599–1606 (IEEE, New York).
9.
HahnJ. O.LeeK. I.‘Nonlinear robust control of torque converter clutch slip system for passenger vehicles using advanced torque estimation algorithms.’Veh. System Dynamics37 (3) (2002): 175–192
10.
ChengD. S.ZhangJ. W.YeX. F.HuangX.-F.‘Sliding mode control approach for electrically controllable clutch of AMT based on the feedback linearization.’J. Dong Hua Univ., Engl. Edn20 (3) (2003): 88–93
11.
ZhangJ.ChenL.XiG.‘System dynamic modeling and adaptive optimal control for automatic clutch engagement of vehicles.’Proc. IMechE, Part D: J. Automobile Engineering216 (12) (2002): 983–991 DOI: 10.1243/095440702762508236.
12.
LeeW.ParkS.SunwooM.‘Towards a seamless development process for automotive engine-control system.’Control Engng Practice12 (2004): 977–986
13.
NoomwongsN.YoshidaH.NagaiM.KobayashiK.YokoiT.‘Study on handling and stability using tire hardware-in-the-loop simulator.’JSAE Rev.24 (2003): 457–464
14.
ThomasB.FeritK.‘Virtual real-time environment for automatic-transmission control units in the form of hardware-in-the-loop.’Int. J. Veh. Autonomous Systems1 (2) (2003): 177–195
15.
LiuG. P.DaleyS.‘Optimal-tuning nonlinear PID control of hydraulic systems.’Control Engng Practice8 (2000): 1045–1053
16.
ErM. J.LowC. B.NahK. H.LimM. H.NgS. Y.‘Real-time implementation of a dynamic fuzzy neural networks controller for a SCARA.’Microprocessor Microsystems26 (2002): 449–461
17.
MontanariM.RonchiF.‘Control and performance evaluation of a clutch servo system with hydraulic actuation.’Control Engng Practice12 (2004): 1369–1379
18.
LyshevskiS. A.NazarovA.‘Control and analysis of synchronous reluctance motors.’ In Proceedings of the American Control Conference, San Diego, California, USA, 1999, pp. 1682–1686 (IEEE, New York).
19.
YuF. M.ChungH. Y.ChenS. Y.‘Fuzzy sliding mode controller design for uncertain time-delayed systems with nonlinear input.’Fuzzy Sets Systems140 (2003): 359–374
20.
LeeJ.-H.YounM.-J.‘A new improved continuous variable structure controller for accurately prescribed tracking control of BLDD servo motors.’Automatica40 (2004): 2069–2074
21.
PieperJ.‘First order dynamic sliding mode control.’. In Proceedings of the 37th IEEE Conference on Decision and control, Tampa, Florida, USA, 1998, pp. 2415–2420 (IEEE, New York).
22.
AbdelhameedM. M.‘Enhancement of sliding mode controller by fuzzy logic with application to robotic manipulators.’Mechatronics15 (2005): 439–458
23.
FungR. F.ShawC. C.‘Region-wise linear fuzzy sliding mode control of the motor-mechanism systems.’J. Sound Vibr.234 (3) (2000): 471–489
24.
KiamH. A.GergoryC.YunL.‘PID control system analysis, design and technology.’IEEE Trans. Control Systems Technol.13 (4) (2005): 559–576
