This study was undertaken to fundamentally understand structure–property relationship of blown films of linear low density polyethylene/low density polyethylene blends over the entire composition range via decoupling orientation effects from their intrinsic properties. Three different low density polyethylene blends with an octene Ziegler–Natta linear low density polyethylene resin were studied. The machine direction tear strengths of blown film of linear low density polyethylene/low density polyethylene blends went through a minimum as the low density polyethylene concentration increased, almost a mirror image of the melt strength curve for these blends. The machine direction tear decreased significantly up to 40% low density polyethylene, much sharper decrease compared to decrease in intrinsic tear suggesting orientation effects dominating the machine direction tear behavior. The decrease in the dart impact and puncture energy was also due to both an increase in the machine direction orientation, and a decrease in the intrinsic toughness due to decrease in the tie chain concentration, as the low density polyethylene content increased.
TroisiEMvanDrongelenMCaelersHJM, et al.
Structure evolution during film blowing: An experimental study using in-situ small angle X-ray scattering.European Polymer Journal2016;
74: 190–208.
2.
MicicPBhattacharyaSNFieldG.Melt strength and elastic behavior of LLDPE/LDPE blends.International Polymer Processing1996;
11: 14–20. DOI: 10.3139/217.960014.
3.
MicicPBhattacharyaSNFieldG.Rheological behavior of LLDPE/LDPE blends under elongational deformation. The effect of molecular structure and melt morphology.International Polymer Processing1997;
12: 110–115. DOI: 10.3139/217.970110.
4.
McicPBhattacharyaSNFieldG.Transient elongational viscosity of LLDPE/LDPE blends and its relevance to bubble stability in the film blowing process.Polymer Engineering and Science1998;
38: 1685–1693.
5.
MicicPBhattacharyaSNFieldG.Rheological behavior of LLDPE/LDPE blends under elongational deformation. Effect of temperature.International Polymer Processing1998;
13: 50–57. DOI: 10.3139/217.980050.
6.
FieldGJMicicPBhattacharyaSN.Melt strength and film bubble instability of LLDPE/LDPE blends.Polymer International1999;
48: 461–466. DOI: 10.1002/(sici)1097-0126(199906)48:6.
7.
MicicPBhattacharyaSN.Rheology of LLDPE, LDPE and LLDPE/LDPE blends and its relevance to the film blowing process.Polymer International2000;
49: 1580–1589. DOI: 10.1002/1097-0126(200012)49:12.
8.
YamaguchiMAbeS.LLDPE/LDPE blends. I. Rheological, thermal, and mechanical properties.Journal of Applied Polymer Science1999;
74: 3153–3159. DOI: 10.1002/(sici)1097-4628(19991220)74:13.
9.
AjjiASammutPHuneaultMA.Elongational rheology of LLDPE/LDPE blends.Journal of Applied Polymer Science2003;
88: 3070–3077. DOI: 10.1002/app.11931.
10.
WagnerMHKheirandishSYamaguchiM.Quantitative analysis of melt elongational behavior of LLDPE/LDPE blends.Rheologica Acta2004;
44: 198–218. DOI: 10.1007/s00397-004-0400-9.
11.
FangYCarreauPJLafleurPG, et al.
Properties of mLLDPE/LDPE blends in film blowing.Polymer Engineering and Science2005;
45: 343–353. DOI: 10.1002/pen.20279.
12.
PerezRRojoEFernandezM, et al.
Basic and applied rheology of m-LLDPE/LDPE blends: miscibility and processing features.Polymer2005;
46: 8045–8053. DOI: 10.1016/j.polymer.2005.06.087.
13.
RobledoNVegaJFNietoJ, et al.
The role of the interface in melt linear viscoelastic properties of LLDPE/LDPE blends: Effect of the molecular architecture of the matrix.Journal of Applied Polymer Science2009;
114: 420–429. DOI: 10.1002/app.30422.
14.
MantiaFPLValenzaAAciernoD.Influence of the structure of linear density polyethylene on the rheological and mechanical properties of blends with low density polyethylene.European Polymer Journal1986;
22: 647–652.
15.
TasPNguyenLTehJ.Melt strength, maximum output, and physical properties of SURPASS1 sLLDPE-LDPE blends in blown film.Journal of Plastic Film & Sheeting2005;
21: 265–279. DOI: 10.1177/8756087905058790.
16.
BrancifortiMCPimentelRBernardiA, et al.
Correlations between processing parameters, morphology, and properties of blown films of linear low-density polyethylene/low-density polyethylene blends. I. Crystalline biaxial orientation by IR and mechanical properties.Journal of Applied Polymer Science2006;
101: 3161–3167. DOI: 10.1002/app.23358.
17.
BrancifortiMCGuerriniLMMachadoR, et al.
Correlations between processing parameters, morphology, and properties of blown films of LLDPE/LDPE blends, part 2: crystalline and amorphous biaxial orientation by WAXD pole figures.Journal of Applied Polymer Science2006;
102: 2760–2767. DOI: 10.1002/app.24403.
18.
CowellTJ. The effects of low levels of various LDPE's on LLDPE resin and blown film properties. TAPPI Polymers, Laminations & Coatings Conference Proceedings, Lake Buena Vista, Florida1992: 77.
19.
FallaDJ. Physical properties of blends of various melt index LDPEs and LLDPE. TAPPI Polymers, Laminations & Coatings Conference Proceedings, Boston, Massachusetts1996: 279.
20.
PlumleyTASehanobishKPatelRM, et al.
Intrinsic Tear Strengths and Their Correlation with Properties of Polymers Made Using INSITE Technology. J Plast Film Sheeting1995;
11: 269–278.
21.
HoKKaleLMontgomeryS.Melt strength of linear low-density polyethylene/low-density polyethylene blends.Journal of Applied Polymer Science2002;
85: 1408–1418. DOI: 10.1002/app.10677.
BerstedBHSleeJDRichterCA.Prediction of rheological behavior of branched polyethylene from molecular structure.Journal of Applied Polymer Science1981;
26: 1001–1014. DOI: 10.1002/app.1981.070260323.
24.
BerstedBH.On the effects of very low levels of long chain branching on rheological behavior in polyethylene.Journal of Applied Polymer Science1985;
30: 3751–3765. DOI: 10.1002/app.1985.070300916.
25.
PatelRMSehanobishKJainP, et al.
Theoretical prediction of tie-chain concentration and its characterization using postyield response.Journal of Applied Polymer Science1996;
60: 749–758. DOI: 10.1002/(sici)1097-4628(19960502)60:5.
26.
PatelRMButlerTIWaltonKL, et al.
Investigation of Processing-Structure-Properties Relationships in Polyethylene Blown Films.Polym Eng Sci1994;
34: 1506–1514.
27.
ElkounSHuneaultMAMcCormickK, et al.
LLDPE‐based mono‐ and multilayer blown films: Property enhancement through coextrusion.Polym Eng Sci2005: 1222–1230.
28.
GuichonOSeguelaRDavidL, et al.
Infulence of the Molecular Architecture of Low-Density Polyethylene on the Texture and Mechanical Properties of Blown Films.J Polym Sci: Part B: Polym Phys2003;
41: 327–340.
29.
HongKStroblG.Network Stretching during Tensile Drawing of Polyethylene: A Study Using X-ray Scattering and Microscopy.Macromolecules2006;
39: 268–273. DOI: 10.1021/ma051726o.
