Laser cutting is often used in the fabrication of Polydimethylsiloxane (PDMS) substrates for novel microdevices such as wearable sensors and microfluidic devices. PDMS is a thermosetting polymer whose material properties are affected by the thermal conditions during the curing process. Since laser cutting exposes the cutting material to high temperatures, this might affect the heat-sensitive material properties. In this work, we examine how laser cutting affects the stiffness of PDMS by measuring the Young’s modulus of PDMS and comparing that to the Young’s modulus of laser-cut PDMS. We find an increase in the Young’s modulus from 0.34 to 0.37 MPa (9%) for PDMS mixed at a ratio of 20:1 base to curing agent. For 10:1 ratio PDMS, we find the increase in Young’s modulus is 31%, from 1.02 to 1.34 MPa.
ChungM, FortunatoG, and RadacsiN.Wearable flexible sweat sensors for healthcare monitoring: a review. J R Soc Interface2019; 16: 20190217.
2.
AfsarimaneshA, NagA, SarkarS, . A review on fabrication, characterization and implementation of wearable strain sensors. Sens Actuators A Phys2020; 315: 112355.
3.
YinF, LuH, PanH, . Highly sensitive and transparent strain sensors with an ordered array structure of AgNWs for wearable motion and health monitoring. Sci Rep2019; 9: 2403.
4.
ChouN, KimY, and KimS.A method to pattern silver nanowires directly on wafer-scale PDMS substrate and its applications. ACS Appl Mater Interfaces2016; 8: 6269–6276.
5.
ShuaiX, ZhuP, ZengW, . Highly sensitive flexible pressure sensor based on silver nanowires-embedded polydimethylsiloxane electrode with microarray structure. Appl Mater Interfaces2017; 9: 26314–26324.
6.
MyersAC, HuangH, and ZhuY.Wearable silver nanowire dry electrodes for electrophysiological sensing. RSC Adv2015; 5(15): 11627–11632.
7.
CampigottoA and LaiY. A novel non-invasive wearable sensor for intraocular pressure measurement. Med Devices Sensors2020; 3: e10086.
8.
AnH, ChenL, LiuX, . A method of manufacturing microfluidic contact lenses by using irreversible bonding and thermoforming. J Micromech Microeng2018; 28: 105008.
9.
FathyJ and LaiY. Using a coil to realize 3D electrodes for dielectrophoresis-based particle concentration. J Micromech Microeng2020; 30: 035009.
10.
ZhangH, ChangH, and NeuzilP. DEP-in-a-chip: Dielectrophoresis applied to microfluidic platforms. Micromachines2019; 10(6): 423.
11.
AzizipourN, AvzpourR, RosenzweigDH, . Evolution of biochip technology: A review from lab-on-a-chip to organ-on-a-chip. Micromachines2020; 11(599).
12.
E-HKo, H-JKim, S-MLee, . Stretchable Ag electrodes with mechanically tunable optical transmittance on wavy-patterned PDMS substrates. Sci Rep, 2017; 7.
JohnstonID, McCluskeyDK, TanC, . Mechanical characterization of bulk Sylgard 184 for microfluidics and microengineering. J Micromech Microeng2014; 24: 035017.
15.
KronerE, MaboudianR, and ArztE.Adhesion characteristics of PDMS surfaces during repeated pull-off force measurements. Adv Eng Mater2010; 12(5): 398–404.
16.
WangZ, VolinskyAA, and GallantND.Crosslinking effect of polydimethylsiloxane elastic modulus measured by custom-built compression instrument. J Appl Polym Sci2014; 131(22): DOI:10.1002/app.41050.
LiuH-B and GongH-Q. Templateless prototyping of polydimethylsiloxane microfluidic structures using a pulsed CO2 laser. J Micromech Microeng2009; 19: 037002.
21.
LiM, LiS, WuJ, . A simple and cost-effective method for fabrication of integrated electronic-microfluidic devices using a laser-patterned PDMS layer. Microfluid Nanofluid2012; 12: 751–760.
22.
SunL, DingA, ChenY, . Fabrication of PDMS chips by laser engraving for protein enrichmentsJ Elect Eng2022; 73: 43–49.
23.
MushtaqRT, WangY, RehmanM, . State-of-the-art and trends in CO2 laser cutting of polymeric materials–A review. Materials2020; 13(8): 3839.
24.
ArifAFM and YilbasBS.Thermal stress developed during the laser cutting process: consideration of different materials. Int J Adv Manuf Tech2008; 37: 698–704.
25.
MiraouiI, BoujelbeneM, and ZaiedM.High-power laser cutting of steel plates: Heat affected zone analysis. Adv Mater Sci Eng2016; 2016: 1242565.
26.
WuC, XuJ, ZhangT, . Precision cutting of PDMS film with UV-nanosecond laser based on heat generation-diffusion regulation. Opt Laser Technol2021; 145(2022), 107462.
27.
KhoshaimAB, ElsheikAH, MoustafaEB, . Experimental investigation on laser cutting of PMMA sheets: Effect of process factors on kerf characteristics. J Mater Res Technol2021; 11: 235–246.
28.
TresanskyAC, JoyceP, RadiceP, . Numerical modeling of high-energy laser effects in polymer and composite materials. J Directed Energy2014; 5: 137–158.
29.
KonariPR, Y-DClayton, VaughanMB, . Experimental analysis of laser micromachining of microchannels in common microfluidic substrates. Micromachines2021; 12: 138.
30.
BentonM, HossanMR, KonariPR, . Effect of process parameters and material properties on laser micromachining of microchannels. Micromachines2019; 10: 123.
31.
HolleAW, S-HChao, HollMR, . Characterization of program controlled CO2 laser-cut PDMS channels for lab-on-a-chip applications. In IEEE Conference on Automation Science and Engineering, Scottsdale, 2007.
32.
SchneiderF, FellnerT, WildeJ, . Mechanical properties of silicones for MEMS. J Micromech Microeng2008; 18: 065008.
33.
JoshiA, KansaraN, DasS, . A study of temperature distribution for laser assisted machining of Ti-6Al-4 V alloy. Procedia Eng2014; 97: 1466–1473.
34.
ChajaM, KramerT, and NeuenschwanderB.Influence of laser spot size and shape on ablation efficiency using pulse laser system. Procedia CIRP2018; 74: 300–304.
35.
FukutaS, NomuraM, IkedaT, . Wavelength dependence of machining performance in UV-, VIS- and NIR-laser cutting of wood. J Wood Sci2016; 62: 316–323.
36.
LuL, ShiY, XuC, . The influence of pulse width and energy on temperature field in metal. Phys Procedia2012; 32: 39–47.
37.
CaminoG, LomakinSM, and LazzariM.Polydimethylsiloxane thermal degradation Part 1: Kinetic aspects. Polymer2001; 42: 2395–2402.
