Optimization of the fibre laser cutting parameters for attainment of high cut edge quality in 10 mm stainless steel plate was demonstrated in this study. The tested process parameters included cutting speed, focal position, and focal length. Optimization of these process parameters enhances the melt removal from the cut kerf so as to prevent the undesired dross adherence on the lower cut edge or even incomplete penetration of the workpiece when the incident intensity is not sufficient to penetrate the workpiece. Dross-free cut edges with lower surface roughness and lower deviation of cut edge squareness could be achieved by reducing the cutting speed from the maximum achievable value, using the longer focal length lens for focusing the laser beam, and with focal position located on the bottom workpiece surface. These conditions enhance a high melt removal rate resulting in a high cut edge quality.
ReadyJ. FFarsonD. F. (Eds) Chapter 12: Laser cutting. LIA handbook of laser materials processing, 2001, pp. 425–470 (Laser Institute of America).
2.
HügelH. New solid-state lasers and their application potentials. Optics and Lasers Engng, 2000, 34, 213–229.
3.
O'NeillWSparkesMVarnhamMHorleyRBirchMWoodsSHarkerA.High power high brightness industrial fiber laser technology. In Proceedings of the 23rd International Congress on Applications of lasers and electro optics (ICALEO), San Francisco, USA, 4–7 October 2004, paper 301, pp. 1–7 (Laser Institute of America).
4.
CanningJ. Fibre lasers and related technologies. Optics and Lasers Engng, 2006, 44, 647–676.
5.
WanderaC. Laser cutting of austenitic stainless steel with a high quality laser beam, Masters Thesis, Lappeenranta University of Technology, Finland, May 2006.
6.
SparkesMGrossMCelottoSZhangTO'NeillW. Practical and theoretical investigations into inert gas cutting of 304 stainless steel using a high brightness fiber laser. J. Laser Applic., 2008, 20, 59–67.
7.
SparkesMGrossMCelottoSZhangTO'NeillW. Inert cutting of medium section stainless steel using a 2.2KW high brightness fibre laser. In Proceeding of the 25th International Congress on Applications of lasers and electro optics (ICALEO), Scottsdale, Arizona, USA, 30 October–2 November 2006, paper 402, pp. 197–205 (Laser Institute of America).
8.
GrossM. SCelottoSO'NeillW. Melt flow in narrow thick-section kerfs. In Proceeding of the 25th International Congress on Applications of lasers and electro optics (ICALEO), Scottsdale, Arizona, USA, 30 October–2 November 2006, paper 403, pp. 206–210 (Laser Institute of America).
9.
HimmerTPinderTMorgenthalLBeyerE.High brightness lasers in cutting applications. In Proceedings of 26th International Congress on Applications of lasers and electro optics (ICALEO), Orlando, Florida, USA, 29 October–1 November 2007, paper 206, pp. 87–91 (Laser Institute of America).
10.
WanderaCKujanpääVSalminenA.Laser power requirement for cutting of thick-section steel and effects of processing parameters on mild steel cut quality. J. Engng Mf, 2010, accepted for publication.
11.
MahrleABartelsFBeyerE. Theoretical aspects of the process efficiency in laser beam cutting with fiber lasers. In Proceedings of 27th International Congress on Applications of lasers and electro optics (ICALEO), Temecula, California, USA, 22–23 October 2008, paper 2006, pp. 703–712 (Laser Institute of America).
12.
MahrleABeyerE.Theoretical aspects of fibre laser cutting. J. Phys. D: Appl. Phys, 2009, 42, 1–9.
13.
MahrleALütkeMBeyerE. Fibre laser cutting: beam absorption characteristics and gas-free remote cutting. Proc. IMechE, Part C: J. Mechanical Engineering Science, 2010, 224, DOI: 10.1243/09544062JMES1747, 1007–1018.
14.
WanderaCSalminenAKujanpääVeli. Inert gas cutting of thick-section stainless steel and medium-section aluminum using a high power fiber laser. J. Laser Applic., 2009, 21, 154–161.
15.
LuganAHiltonP. ATaylorD. W.The effects of steel composition on the laser cut edge quality of carbon and C-Mn steels. In Proceedings of 21st International Congress on Applications of lasers and electro optics (ICALEO), Scottsdale, Arizona, USA, 14 October–17 2002 (Laser Institute of America).
Anon.. http://www.outokumpu.com/33392.epibrw (access date 3 June 2010).
18.
WanderaCKujanpääV. Characterization of the melt removal rate in laser cutting of thick-section stainless steel. J. Laser Applic., 2010, accepted for publication.
19.
Anon.. Thermal cutting – classification of thermal cuts. Geometrical product specification and quality tolerances, SFS EN ISO 9013: 2002, 19 August 2002 (European Committee for Standardization).
20.
SteenW. M. Chapter 2: basic laser optics. Laser material processing, third edition, 2003, pp. 70–71, and 87 (Springer, New York).
