Laser power requirement for cutting thick-section steel and effects of processing parameters on mild steel cut quality

Abstract

The high-power fibre laser presents a possibility for the application of solid-state lasers in thick-section metal cutting, a field which has been dominated by high-power CO₂ lasers. The current paper presents the lumped-parameter formulation of the laser power requirement as a function of cutting speed for oxygen-assisted laser cutting of mild steel and nitrogen-assisted laser cutting of stainless steel. The calculated laser power requirement is compared with the incident laser power used in the cutting of 15 mm mild steel with oxygen assist gas and 10 mm stainless steel with nitrogen assist gas using a multi-mode 5 kW fibre laser and a 4 kW CO₂ laser. The incident laser power required for cutting at a given cutting speed is found to be lower for fibre laser cutting than for the CO₂ laser cutting, indicating a higher absorption of the fibre laser beam. The effects of process parameters on the cut kerf quality in mild steel laser cutting with oxygen assist gas using the high-power fibre laser are presented. The critical process parameters affecting the quality of the cutting process and the resulting cut kerf are the cutting speed, oxygen pressure, and nozzle diameter.

Keywords

laser cutting thick section mild steel stainless steel fibre laser

References

Wandera

Salminen

Olsen

F. O

Kujanpää

. Cutting of stainless steel with a fiber and disk laser. In Proceedings of the 25th International Conference on Lasers and electro optics (ICALEO). 30 October–2 November 2006, Scottsdale, Arizona, USA(Laser Institute of America, Orlando, Florida, USA, 211–220.

Sparkes

Gross

Celotto

Zhang

O'Neill

. Inert cutting of medium section stainless steel using a 2.2 kW high power fibre laser. In Proceedings of the 25th International Conference on Lasers and electro optics (ICALEO). 30 October–2 November 2006, Scottsdale, Arizona, USA(Laser Institute of America, Orlando, Florida, USA, 197–205.

Xie

Kar

Rothenflue

J. A

Latham

W. P

. Temperature-dependent absorptivity and cutting capability of CO₂, Nd:YAG and chemical oxygen–iodine lasers. J. Laser Applic., 1997, 9, 77–85.

Mahrle

Bartels

Beyer

. Theoretical aspects of the process efficiency in laser beam cutting with fiber lasers. In Proceedings of the 27th International Conference on Applications of lasers and electro optics (ICALEO). 22–23 October 2008, Temecula, California, USA(Laser Institute of America, Orlando, Florida, USA, 703–712.

Golnabi

Bahar

. Investigation of optimum condition in oxygen gas-assisted laser cutting. Optic. Laser Technol., 2009, 41, 454–460.

Yilbas

B. S

. Experimental investigation into CO₂ laser cutting parameters. J. Mater. Process. Technol., 1996, 58, 323–330.

Powell

Petring

Kumar

R. V

Al-Mashikhi

S. O

Kaplan

A. F. H

Voisey

K. T

. Laser–oxygen cutting of mild steel: the thermodynamics of the oxidation reaction. J. Phys. D: Appl. Phys., 2009, 42, 1–11.

Yilbas

B. S

. Laser cutting of thick sheet metals: effects of cutting parameters on kerf size variations. J. Mater. Process. Technol., 2008, 201, 285–290.

Tani

Tomesani

Campana

. Prediction of melt geometry in laser cutting. Appl. Surf. Sci., 2003, 208–209, 142–147.

10.

Ivarson

. On the physics and chemical thermodynamics of laser cutting, 1993, Doctoral Thesis (1993:114, papers I and II), Department of Applied Physics and Mechanical Engineering, Luleå University of Technology.

11.

Welty

J. R.

Engineering heat transfer SI version, 1978 (John Wiley & Sons, Chichester, UK, 20–25.

12.

Carslaw

H. S

Jaeger

J. C

. Conduction of heat in solids, edition 2, 1959 (Clarendon Press, Oxford, UK, 6–9.

13.

Schulz

Becker

Franke

Kemmerling

Herziger

. Heat conduction losses in laser cutting of metals. J. Phys. D: Appl. Phys., 1993, 26, 1357–1363.

14.

Birks

Meier

G. H

. Introduction to high temperature oxidation of metals, 1983 (Edward Arnold Ltd, London, 2, 31–43.

15.

LIA handbook of laser materials processing, Ready

J. F

Farson

D. F

. 2001 (Laser Institute of America, Orlando, Florida, USA, 428–430.

16.

Callister

W. D

. Materials science and engineering: An introduction, edition 6, 2003 (John Wiley & Sons, Chichester, UK, 95–99, 758.

17.

Kay

J. M

Nedderman

R. M

. An introduction to fluid mechanics and heat transfer, edition 3, 1974 (Cambridge University Press, Cambridge, UK, 11–11.

18.

Kubaschewski

Hopkins

B. E

. Oxidation of metals and alloys, 1953 (Butterworth Scientific Publications Ltd, London, 1–4, 20–26, 46–54.

19.

Bäuerle

. Laser processing and chemistry, edition 3, 2000 (Springer-Verlag, Berlin/Heidelberg, Germany, 695, 705–695, 705.

20.

CRC handbook of chemistry and physics, Lide

D. R

. edition 89, 2008–2009, section 4; available from http://www.hbcpnetbase.com/ (access date 5 October 2009), 68, 79–68, 79.

21.

Anon. Hot Rolled Plates, Sheets and Coils; available from http://www.ruukki.com/www/materials.nsf/mate rials/320D13CB0912BDD7C225723600408B24/$File/La ser_04.2006_EN.pdf?openElement (access date 1 October 2009).

22.

Anon. EN 1.4301, AISI 304; EN 1.4307, AISI 304L, Outo Kumpu product information, 2009; available from http://www.outokumpu.com/43395.epibrw (access date 1 October 2009).

23.

Arata

Maruo

Miyamoto

Takeuchi

. Dynamic behavior in laser gas cutting of mild steel. Trans. JWRI, 1979, 8, 15–26.

24.

Miyamoto

Maruo

. The mechanism of laser cutting. Welding in the World (UK), 1991, 29, 283–294.