Pre-operative virtual three-dimensional planning for proximal humerus fractures: A proof-of-concept study

Abstract

Purpose

To (1) evaluate surgeon agreement on plating features (position and screw length) in virtual 3D planning software, (2) describe outcomes (fracture reduction, plate position, malpositioning of calcar screws and screw lengths) of plate fixations planned with routine pre-operative assessment (2D- and 3D CT imaging) and those planned with dedicated virtual 3D software of the same proximal humerus fracture.

Methods

Fourteen proximal humerus fractures were retrospectively reduced and fixed with virtual planning software by eight attending orthopaedic surgeons and compared to the true surgical fixation with post-operative computed tomography (CT) scans. Reduction differences were quantified using CT micromotion analysis.

Results

Intraclass correlation for screw lengths was 0.97 (95% CI: 0.96–0.98) and 0.90 (95% CI: 0.79–0.96) for plate position. Mean difference in total fracture rotation of the head between the virtual and conventional group was 22.0°. Plate position in the virtual planning group was 3.2 mm more proximal. There were no differences in inferomedial quadrant calcar screw positioning and, apart from the superior posterior converging screw, no significant differences in screw lengths.

Conclusion

Reproducibility on plate position and screw length with virtual planning software is adequate. Apart from fracture reduction, virtual planning yielded similar plate positions, screw malpositioning rates and lengths compared to routine pre-operative assessment.

Keywords

3D virtual planning CT micromotion analysis proximal humerus fractures surgical planning screw lengths reduction calcar screws plate position

Get full access to this article

View all access options for this article.

References

Gardner

Weil

Barker

, et al. The importance of medial support in locked plating of proximal humerus fractures. J Orthop Trauma 2007; 21: 185–191.

Helfen

Siebenbürger

Fleischhacker

, et al.

Open reduction and internal fixation of displaced proximal humeral fractures. Does the surgeon’s experience have an impact on outcomes?

PLoS One 2018; 13: e0207044.

Wang

Sheng

Rui

, et al. The neck-shaft angle is the key factor for the positioning of calcar screw when treating proximal humeral fractures with a locking plate. Bone Joint J 2020; 102-B: 1629–1635.

McMillan

Johnstone

. Primary screw perforation or subsequent screw cut-out following proximal humerus fracture fixation using locking plates: a review of causative factors and proposed solutions. Int Orthop 2018; 42: 1935–1942.

Omid

Trasolini

Stone

, et al. Principles of locking plate fixation of proximal humerus fractures. J Am Acad Orthop Surg 2021; 29: E523–E535.

Panagiotopoulou

Varga

Richards

, et al. Late screw-related complications in locking plating of proximal humerus fractures: a systematic review. Injury 2019; 50: 2176–2195.

Fletcher

JWA

Windolf

Grünwald

, et al. The influence of screw length on predicted cut-out failures for proximal humeral fracture fixations predicted by finite element simulations. Arch Orthop Trauma Surg 2019; 139: 1069–1074.

Südkamp

Bayer

Hepp

, et al. Open reduction and internal fixation of proximal humeral fractures with use of the locking proximal humerus plate. Results of a prospective, multicenter, observational study. J Bone Joint Surg Am 2009; 91: 1320–1328.

Prijs

Schoolmeesters

Eygendaal

, et al. 3D Virtual pre-operative planning may reduce the incidence of dorsal screw penetration in volar plating of intra-articular distal radius fractures. Eur J Trauma Emerg Surg 2022; 48: 3911–3921.

10.

Chen

Jia

Qiang

, et al. Computer-assisted virtual surgical technology versus three-dimensional printing technology in preoperative planning for displaced three and four-part fractures of the proximal end of the humerus. J Bone Joint Surg Am 2018; 100: 1960–1968.

11.

Jia

Chen

Qiang

, et al. Compared to X-ray, three-dimensional computed tomography measurement is a reproducible radiographic method for normal proximal humerus. J Orthop Surg Res 2016; 11: 82.

12.

Jia

Chen

Qiang

, et al.

Detection of intra-articular screw penetration of proximal humerus fractures: is postoperative computed tomography the necessary imaging modality?

Acad Radiol 2019; 26: 257–263.

13.

Totoki

Yoshii

Kusakabe

, et al. Screw length optimization of a volar locking plate using three dimensional preoperative planning in distal radius fractures. J Hand Surg (Asian Pac Vol) 2018; 23: 520–527.

14.

Angelomenos

Mohaddes

Itayem

, et al. Precision of low-dose CT-based micromotion analysis technique for the assessment of early acetabular cup migration compared with gold standard RSA: a prospective study of 30 patients up to 1 year. Acta Orthop 2022; 93: 459–465.

15.

Sandberg

Tholén

Carlsson

, et al. The anatomical SP-CL stem demonstrates a non-progressing migration pattern in the first year: a low dose CT-based migration study in 20 patients. Acta Orthop 2020; 91: 654–659.

16.

Valstar

Gill

Ryd

, et al. Guidelines for standardization of radiostereometry (RSA) of implants. Acta Orthop 2005; 76: 563–572.

17.

Brodén

Giles

Popat

, et al. Accuracy and precision of a CT method for assessing migration in shoulder arthroplasty: an experimental study. Acta Radiol 2020; 61: 776–782.

18.

Koo

. A guideline of selecting and reporting intraclass correlation coefficients for reliability research. J Chiropr Med 2016; 15: 155–163.

19.

Erdfelder

Faul

Buchner

, et al. Statistical power analyses using G*Power 3.1: tests for correlation and regression analyses. Behav Res Methods 2009; 41: 1149–1160.

20.

Faul

Erdfelder

Lang

, et al. G*Power 3: a flexible statistical power analysis program for the social, behavioral, and biomedical sciences. Behav Res Methods 2007; 39: 175–191.

21.

Gruson

. CORR Insights®: 3D-printed handheld models do not improve recognition of specific characteristics and patterns of three-part and four-part proximal humerus fractures. Clin Orthop Relat Res 2022; 480: 160–162.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

0.52 MB

0.23 MB

0.24 MB

0.25 MB

0.47 MB

0.30 MB

0.03 MB