Thermal-force coupling simulation of carbon fibre-reinforced poly-ether-ether-ketone thermoplastic composites during the laser-assisted automated tape placement process

Abstract

To reveal the thermal-force coupling characteristics of the laser in-situ consolidation (ISC) of carbon fibre-reinforced poly-ether-ether-ketone (CF/PEEK) composites, a two-dimensional transient thermal-force model of CF/PEEK composites was constructed using COMSOL Multiphysics finite element simulation software to calculate the temperature history and the thermal stress variation of CF/PEEK composites during the laser-assisted automated tape placement (LATP) process. The results show that the temperature field formed on the surface of each layer by the laser spot during LATP is stable, and the temperature gradient at the front of the spot movement direction is higher than that at the back edge. The maximum stresses in the laminate occur on both sides of the first CF/PEEK layer and the stresses are unevenly distributed along the length and thickness directions of the lay-up. The composite material on both sides of the laminate tends to ‘shrink’ compared to its original position.

Keywords

flat-top laser thermal-force simulation temperature history laser in-situ consolidation

Get full access to this article

View all access options for this article.

References

Kim

K-Y

. Interlaminar fracture toughness of CF/PEI composites at elevated temperatures: roles of matrix toughness and fibre/matrix adhesion. Compos A: Appl Sci Manuf 2004; 35: 477–487.

Schledjewski

. Thermoplastic tape placement process – in situ consolidation is reachable. Plast Rubber Compos 2009; 38: 379–386.

Stokes-Griffin

Compston

Matuszyk

, et al. Thermal modelling of the laser-assisted thermoplastic tape placement process. J Thermoplast Compos Mater 2015; 28: 1445–1462.

Donough

Shafaq, St John

, et al. Process modelling of in-situ consolidated thermoplastic composite by automated fibre placement – a review. Compos A: Appl Sci Manuf 2022; 163: 107179.

Baran

Cinar

Ersoy

, et al. A review on the mechanical modeling of composite manufacturing processes. Arch Comput Methods Eng 2017; 24: 365–395.

Aghababaei Tafreshi

Van Hoa

Shadmehri

, et al. Determination of convective heat transfer coefficient for automated fiber placement (AFP) for thermoplastic composites using hot gas torch. Adv Manuf: Polym Compos Sci 2020; 6: 86–100.

Sarrazin

Springer

. Thermochemical and mechanical aspects of composite tape laying. J Compos Mater 1995; 29: 1908–1943.

Sunderland

Månson

J-A

. A thermoviscoelastic analysis of process-induced internal stresses in thermoplastic matrix composites: thermoviscoelastic analysis. Polym Compos 2001; 22: 579–592.

Stokes-Griffin

Compston

. Investigation of sub-melt temperature bonding of carbon-fibre/PEEK in an automated laser tape placement process. Compos A: Appl Sci Manuf 2016; 84: 17–25.

10.

Fedulov

. Modeling of manufacturing of thermoplastic composites and residual stress prediction. Aerosp Syst 2018; 1: 81–86.

11.

Lynam

Milani

Trudel-Boucher

, et al. Predicting dimensional distortions in roll forming of comingled polypropylene/glass fiber thermoplastic composites: on the effect of matrix viscoelasticity. J Compos Mater 2014; 48: 3539–3552.

12.

Chapman

Gillespie

Pipes

, et al. Prediction of process-induced residual stresses in thermoplastic composites. J Compos Mater 1990; 24: 616–643.

13.

Manson

J-AE

Seferis

. Process simulated laminate (PSL): a methodology to internal stress characterization in advanced composite materials. J Compos Mater 1992; 26: 405–431.

14.

Barnes

Byerly

. The formation of residual stresses in laminated thermoplastic composites. Compos Sci Technol 1994; 51: 479–494.

15.

Yadav

Wachtarczyk

Gąsior

, et al. In-line residual strain monitoring for thermoplastic automated tape layup using fiber Bragg grating sensors. Polym Compos 2022; 43: 1590–1602.

16.

Stokes-Griffin

Kollmannsberger

Ehard

, et al. Manufacture of steel–CF/PA6 hybrids in a laser tape placement process: effect of first-ply placement rate on thermal history and lap shear strength. Compos A: Appl Sci Manuf 2018; 111: 42–53.

17.

Zhengqi

Jun

Dajun

, et al. Optimization of thermal model and prediction of crystallinity during the laser-assisted tape winding process. J Reinf Plast Compos 2021; 40: 606–618.

18.

Suemasu

Aoki

Hoshi

, et al. Thermal analysis for in-situ consolidation in the AFP process. Compos A: Appl Sci Manuf 2023; 172: 107577.