Pulsed Nd:YAG laser beam welding was performed at five different power levels (360 W, 380 W, 400 W, 420 W and 440 W), and the relationship between microstructure and nano creep behaviour was investigated for Ti5Al2.5Sn alloy. Microstructural analysis indicated a reduction in grain size in fusion zone, with an increase in the average laser power. In the fusion zone (FZ) of all the beads, acicular α and ά martensite were observed and confirmed by SEM analysis. Due to the formation of the α and ά phases during welding, the microhardness and nanohardness in the FZ increased by ∼71% and ∼58%, respectively, above that of the base alloy. Nano creep analysis suggested diffusional creep as the deformation mechanism in all the beads, except the one performed at an average power of 440 W since its stress exponent was less than 2.
LuoSDQianM. Microwave processing of titanium and titanium alloys for structural, biomedical and shape memory applications: current status and challenges. Mater Manuf Processes2018; 33: 35–49.
2.
KhorevAI. Development of titanium sheet alloys for welded structures working at high temperatures. Weld Int2016; 30: 389–394.
3.
RevathiAMageshSBallaVK, et al.Current advances in enhancement of wear and corrosion resistance of titanium alloys – a review. Mater Technol2016; 31: 696–704.
4.
Humberto Mota de SiqueiraRCapella de OliveiraARivaR, et al.Comparing mechanical behaviour of aluminium welds produced by laser beam welding (LBW), friction stir welding (FSW), and riveting for aeronautical structures. Weld Int2016; 30: 497–503.
5.
BoyerRRBriggsRD. The use of β titanium alloys in the aerospace industry. J Mater Eng Perform2005; 14: 681–685.
6.
BillinghurstEEJr. Tensile properties of cast titanium alloys: Titanium-6Al-4 V ELI and Titanium-5Al-2.5Sn ELI. 1992.
7.
SunQYSongSJZhuRH, et al.Toughening of titanium alloys by twinning and martensite transformation. J Mater Sci2002; 37: 2543–2547.
8.
TanMJChenGWThiruvarudchelvanS. High temperature deformation in ti-5Al-2.5Sn alloy. J Mater Process Technol2007; 192–193: 434–438.
9.
SunQYGuHC. Tensile and low-cycle fatigue behavior of commercially pure titanium and Ti-5Al-2.5Sn alloy at 293 and 77 K. Mater Sci Eng A2001; 316: 80–86.
10.
GangwarKRamuluM. Friction stir welding of titanium alloys: a review. Mater Des2018; 141: 230–255.
11.
YelamasettiBVardhanTVRamanaGV. Study of metallurgical changes and mechanical properties of dissimilar weldments developed by interpulse current TIG welding technique. Proc IMechE, Part C: J Mechanical Engineering Science2021; 235: 2985–2997.
12.
JunaidMKhanFNMirzaMR, et al.Microstructure, mechanical properties and residual stress distribution in pulsed tungsten inert gas welding of Ti–5Al–2.5Sn alloy. Proc IMechE, Part L: J Materials: Design and Applications2019; 233: 2030–2044.
13.
KhanFNJunaidMBaigMN, et al.Response surface approach to minimize the residual stresses in full penetration pulsed TIG weldments of Ti-5Al-2.5Sn alloy. Proc IMechE, Part C: J Mechanical Engineering Science2019; 233: 2778–2793. DOI: 10.1177/0954406218793440.
14.
KarpagarajASiva shanmugamNSankaranarayanasamyK. Some studies on mechanical properties and microstructural characterization of automated TIG welding of thin commercially pure titanium sheets. Mater Sci Eng A2015; 640: 180–189.
15.
GaoXLZhangLJLiuJ, et al.A comparative study of pulsed Nd: YAG laser welding and TIG welding of thin Ti6Al4V titanium alloy plate. Mater Sci Eng A2013; 559: 14–21.
16.
RiofríoPGCapelaCAFerreiraJAM, et al.Interactions of the process parameters and mechanical properties of laser butt welds in thin high strength low alloy steel plates. Proc IMechE, Part L: J Materials: Design and Applications2020; 234: 665–680.
17.
SalminenAPiiliHPurtonenT. The characteristics of high power fibre laser welding. Proc IMechE, Part C: J Mechanical Engineering Science2010; 224: 1019–1029.
18.
CostaAMirandaRQuintinoL, et al.Analysis of beam material interaction in welding of titanium with fiber lasers. Mater Manuf Process2007; 22: 798–803.
19.
ChenZLiJLiuJ, et al.Creep behavior of fusion zone and base metal of the electron beam weldments of a near-alpha titanium alloy. J Mater Sci Technol2010; 26: 564–571.
20.
SquillaceAPriscoUCilibertoS, et al.Effect of welding parameters on morphology and mechanical properties of Ti-6Al-4 V laser beam welded butt joints. J Mater Process Technol2012; 212: 427–436.
21.
KrasnoperovMYPietersRRGMRichardsonIM. Weld pool geometry during keyhole laser welding of thin steel sheets. Sci Technol Weld Join2004; 9: 501–506.
22.
CaoXJahaziM. Effect of welding speed on butt joint quality of Ti-6Al-4 V alloy welded using a high-power Nd:YAG laser. Opt Lasers Eng2009; 47: 1231–1241.
23.
AkmanEDemirACanelT, et al.Laser welding of Ti6Al4V titanium alloys. J Mater Process Technol2009; 209: 3705–3713.
24.
ZhongYXieJChenY, et al.Microstructure and mechanical properties of micro laser welding NiTiNb/Ti6Al4V dissimilar alloys lap joints with nickel interlayer. Mater Lett2022; 306: 130896. https://doi.org/10.1016/j.matlet.2021.130896
25.
PengHFangWDongC, et al.Nano-mechanical properties and creep behavior of ti6al4v fabricated by powder bed fusion electron beam additive manufacturing. Materials (Basel) 2021; 11: 3004. DOI: 10.3390/ma14113004. Epub ahead of print 2021.
26.
JunaidMRahmanKKhanFN, et al.Comparison of microstructure, mechanical properties, and residual stresses in tungsten inert gas, laser, and electron beam welding of Ti–5Al–2.5Sn titanium alloy. Proc IMechE, Part L: J Materials: Design and Applications2019; 233: 1336–1351.
27.
JunaidMKhanFNRahmanK, et al.Effect of laser welding process on the microstructure, mechanical properties and residual stresses in Ti-5Al-2.5Sn alloy. Opt Laser Technol2017; 97: 405–419.
28.
KhorramADavoodi JamaloeiAJafariA. Surface transformation hardening of Ti-5Al-2.5Sn alloy by pulsed Nd:YAG laser: an experimental study. Int J Adv Manuf Technol2019; 100: 3085–3099.
29.
LuoLZhaoXLiuX, et al.Creep behavior of UFG CP Ti at room temperature. In: IOP Conference series: materials science and engineering. IOP Publishing, p. 012062. DOI:10.1088/1757-899X/250/1/012062
30.
BaruahMBagS. Influence of pulsation in thermo-mechanical analysis on laser micro-welding of Ti6Al4V alloy. Opt Laser Technol2017; 90: 40–51.
31.
TzengYF. Parametric analysis of the pulsed nd:YAG laser seam-welding process. J Mater Process Technol2000; 102: 40–47.
32.
SuryanarayanaCIvanovEBoldyrev VV. The science and technology of mechanical alloying. Mater Sci Eng A2001; 304–306: 151–158.
33.
OliverWPharrGM. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res1992; 7: 1564–1583.
34.
OliverWCFabesBD. The relationship between indentation and uniaxial creep in amorphous selenium. J Mater Res1995; 10: 2024–2032.
35.
LiuXZhangQZhaoX, et al.Ambient-temperature nanoindentation creep in ultrafine-grained titanium processed by ECAP. Mater Sci Eng A2016; 676: 73–79.
36.
HuJSunGZhangX, et al.Effects of loading strain rate and stacking fault energy on nanoindentation creep behaviors of nanocrystalline Cu, Ni-20 wt.% Fe and Ni. J Alloys Compd2015; 647: 670–680.
37.
NguyenNVPhamTHKimSE. Microstructure and strain rate sensitivity behavior of SM490 structural steel weld zone investigated using indentation. Constr Build Mater2019; 206: 410–418.
38.
ZengliangGYuxuanSZhouxinP, et al.Nanoindentation investigation on the creep behavior of P92 steel weld joint after creep-fatigue loading. Int J Fatigue2020; 134: 105506.
39.
SongYHuangXGaoZ, et al.Nanoindentation creep behavior of RPV’s weld joint at room temperature. Mech Time-Dependent Mater2020; 24: 253–263.
40.
LucasBNOliverWC. Indentation power-law creep of high-purity indium. Metall Mater Trans A1999; 30: 601–610.
41.
SuCHerbertEGSohnS, et al.Measurement of power-law creep parameters by instrumented indentation methods. J Mech Phys Solids2013; 61: 517–536.
AhmedTRackHJ. Phase transformations during cooling in α + β titanium alloys. Mater Sci Eng A1998; 243: 206–211.
44.
LiuHNakataKYamamotoN, et al.Mechanical properties and strengthening mechanisms in laser beam welds of pure titanium. Sci Technol Weld Join2011; 16: 581–585.
45.
JunaidMKhanFNBakshN, et al.Study of microstructure, mechanical properties and residual stresses in full penetration electron beam welded Ti-5Al-2.5Sn alloy sheet. Mater Des2018; 139: 198–211.
46.
ZengLBielerTR. Effects of working, heat treatment, and aging on microstructural evolution and crystallographic texture of α, α′, α″ and β phases in Ti-6Al-4 V wire. Mater Sci Eng A2005; 392: 403–414.
47.
ZhaoXLuXWangK, et al.Investigation on the microstructure and mechanical properties of Ti6Al4V titanium alloy electron beam welding joint. Proc IMechE, Part C: J Mechanical Engineering Science2022; 236: 2957–2966.
48.
MehdiBBadjiRJiV, et al.Microstructure and residual stresses in Ti-6Al-4 V alloy pulsed and unpulsed TIG welds. J Mater Process Technol2016; 231: 441–448.
49.
WuBBWangZQWangXL, et al.Relationship between high angle grain boundaries and hardness after γ→α transformation. Mater Sci Technol2019; 35: 1803–1814.
50.
LiYBushbyAJDunstanDJ. The Hall-Petch effect as a manifestation of the general size effect. Proc R Soc A Math Phys Eng Sci 2016; 472: 441–448. DOI: 10.1098/rspa.2015.0890. Epub ahead of print 2016.
51.
MotykaMKubiakKSieniawskiJ, et al. Phase Transformations and Characterization of α + β Titanium Alloys. In Comprehensive Materials Processing. Amsterdam: Elsevier, 2014. DOI: 10.1016/B978-0-08-096532-1.00202-8.
52.
SuXTaoWChenY, et al.Microstructure and tensile property of the joint of Laser-MIG hybrid welded thick-section TC4 alloy. Metals (Basel)2018; 8: 1002. DOI: 10.3390/met8121002
53.
Hainsworth SVChandlerHWPageTF. Analysis of nanoindentation load-displacement loading curves. J Mater Res1996; 11: 1987–1995.
54.
PöhlF. Pop-in behavior and elastic-to-plastic transition of polycrystalline pure iron during sharp nanoindentation. Sci Rep 2019; 9: 15350. DOI: 10.1038/s41598-019-51644-5.
55.
AsifHImran KhanMShehbazT, et al.Effect of welding current on the microstructure, residual stresses, mechanical properties and nano-mechanical behaviour of P-TIG welded TiNi binary shape-memory alloy. Proc IMechE, Part L: J Materials: Design and Applications2022; 236: 1829–1841.
56.
VlcakPSepitkaJDrahokoupilJ, et al.Structural characterization and mechanical properties of a titanium nitride-based nanolayer prepared by nitrogen ion implantation on a titanium alloy. J Nanomater2016; 1–7. DOI: 10.1155/2016/9214204
57.
WangQSunDLNaY, et al.Effects of TIG welding parameters on morphology and mechanical properties of welded joint of Ni-base superalloy. Procedia Eng2011; 10: 37–41.
58.
MahmudiRPourmajidianMGeranmayehAR, et al.Indentation creep of lead-free Sn-3.5Ag solder alloy: effects of cooling rate and Zn/Sb addition. Mater Sci Eng A2013; 565: 236–242.
59.
NixWDSiegelRW. Nanoindentation of nanocrystalline ZnO. J Mater Res1992; 7(4): 973–979.
60.
Van SwygenhovenHDerletPM. Grain-boundary sliding in nanocrystalline fcc metals. Phys Rev B Condens Matter Mater Phys2001; 64: 224105.
61.
ShehbazTKhanFNJunaidM, et al.Investigating nanoindentation creep behavior of pulsed-TIG welded inconel 718 and commercially pure titanium using a vanadium interlayer. Metals (Basel)2021; 11: 1492.
