Indentation creep was used to analyze the heterogeneity of the mechanical properties in base metal, heat affected zone and fusion zone of titanium alloy weldments obtained using TIG welding process which is generally employed in aerospace industries. For all the weld zones, creep deformation was analyzed using nanoindenter, AFM and microhardness testing. Nanoindentation creep depth was plotted with respect to time using data from the hold stage and CSRs were calculated using empirical relations. The analysis of creep stress exponents (CSE) was indicative of an active creep mechanism for all the weld zones however, a notable variation between the stress exponents and creep mechanism was observed among base metal, heat affected zone and fusion zone. Moreover, Vickers microindentation was used to measure creep of Ti-5Al-2.5Sn alloy weldment using Sargent-Ashby model. However, it did not give the realistic values creep behavior when compared to literature and nanoindentation measurements. It was observed that the phase change, grain size and the loading strain rate (LSR) significantly affected the creep behavior of the Ti-5Al-2.5Sn weldment.
JunaidMKhanFNRahmanK, et al.Effect of laser welding process on the microstructure, mechanical properties and residual stresses in Ti-5Al-2.5Sn alloy. Opt Laser Technol2017; 97: 405–419.
2.
JunaidMKhanFNBakshN, et al.Study of microstructure, mechanical properties and residual stresses in full penetration electron beam welded Ti-5Al-2.5Sn alloy sheet. Mater Des2018; 139: 198–211.
3.
GaoXZhangLLiuJ, et al.Comparison of Tensile damage evolution in Ti6A14 V joints between Laser beam welding and Gas tungsten Arc welding. J Mater Eng Perform2014; 23: 4316–4327.
4.
LiJShenJHuS, et al.Microstructure and mechanical properties of Ti-22Al-25Nb / TA15 dissimilar joint fabricated by dual-beam laser welding. Opt Laser Technol2019; 109: 123–130.
5.
IltafAJunaidMKhanFN, et al.Influence of electron beam oscillation patterns on the microstructure, texture, residual stress and mechanical properties of Ti-5Al-2.5Sn alloy weldments. Proc Inst Mech Eng Part B J Eng Manuf 2020; (special issue 2020): 1–15.
6.
JunaidMNawazFTauheedK, et al.Influence of filler on the microstructure, mechanical properties and residual stresses in TIG weldments of dissimilar Titanium alloys. Acta Metall Sin (English Lett.) 2021; 34: 1395–1406.
7.
ChuCYHsiehCTTsayLW. Microstructure and notched tensile fracture of Ti-6Al-4 V to Ti-4.5Al-3V-2Fe-2Mo dissimilar welds. Mater Des2014; 63: 14–19.
8.
ZhouWChewKG. Effect of welding on impact toughness of butt-joints in a titanium alloy. Mater Sci Eng A2003; 347: 180–185.
9.
NiuPLiWYangC, et al.Low cycle fatigue properties of friction stir welded dissimilar 2024-to-7075 aluminum alloy joints. Mater Sci Eng A2021: 832: 142423.
10.
HydeTHSunWWilliamsJA. Creep analysis of pressurized circumferential pipe weldments - A review. J Strain Anal Eng Des2003; 38: 1–30.
11.
CraineRENewmanMG. Modelling creep failure in welded plates under uniaxial loading. J Strain Anal Eng Des1996; 31: 117–124.
12.
BrowneRJCaneBJParkerJD, et al. Creep failure analysis of butt welded tubes. In: Creep and fracture of engineering materials and structures. Tsukuba: Pineridge Press, 1981, pp. 645–649.
13.
CoussementCDe WitteMDe BackerT, et al.Internal pressure creep testing on welded components of modified 9% Cr and 12% Cr steel.
14.
HepworthJK. The effect of residual stress on the creep deformation of welded pipe. Int J Press Vessel Pip1984; 15: 271–290.
15.
WuYEWangYT. Effect of filler metal and postwelding heat treatment on mechanical properties of Al-Zn-Mg alloy weldments. J Mater Eng Perform2010; 19: 1362–1369.
TańskiTSrokaMZielińskiA. Introductory chapter: why creep is continuously interesting for science. In: Creep. IntechOpen, 2018, pp. 1–6.
18.
HartEW. Theory of the tensile testActa Metall1967; 15: 351–355.
19.
AsyrafMRMIshakMRSapuanSM, et al.Conceptual design of multi-operation outdoor flexural creep test rig using hybrid concurrent engineering approach. J Mater Res Technol2020; 9: 2357–2368.
20.
DebschützKDCaspersBSchneiderGA, et al.Critical evaluation of the compression creep testJ Am Ceram Soc1993; 76: 2468–2474.
21.
ChiangDLiJCM. Impression creep of lead. J Mater Res1994; 9: 903–908.
22.
WeihsTPPethicaJB. Monitoring time-dependent deformation in small volumes. MRS Online Proc Libr1992; 239: 325–330.
LiWBWarrenR. A model for nano-indentation creep. Acta Metall Mater1993; 41: 3065–3069.
25.
LeeEHRadokJRM. The contact problem for viscoelastic bodies.
26.
FengGNganAHW. Effects of creep and thermal drift on modulus measurement using depth-sensing indentation. J Mater Res2002; 17: 660–668.
27.
HuangPFeiWKeweiX. A method for testing the creep performance of metal film at room temperature. ZL200510124587.8, 2006.
28.
SongYHuangXGaoZ, et al.Nanoindentation creep behavior of RPV's Weld joint at room temperature. Mech Time-Dependent Mater2020; 24: 253–263.
29.
MayoMJSiegelRWLiaoYX, et al.Nanoindentation of nanocrystalline ZnO. J Mater Res1992; 7: 973–979.
30.
LucasBNOliverWC. Indentation power-law creep of high-purity indium. Metall Mater Trans A1999; 30: 601–610.
31.
HassaanMJunaidMShahbazT, et al.Nanomechanical response of pulsed Tungsten Inert Gas welded Titanium Alloy by nanoindentation and atomic force microscopy. J Mater Eng Perform 2021; 30: 1490–1503.
32.
GoodallRClyneTW. A critical appraisal of the extraction of creep parameters from nanoindentation data obtained at room temperature. Acta Mater2006; 54: 5489–5499.
33.
SuCHerbertEGSohnS, et al.Measurement of power-law creep parameters by instrumented indentation methods. J Mech Phys Solids2013; 61: 517–536.
34.
ShenLCheongWCDFooYL, et al.Nanoindentation creep of tin and aluminium: a comparative study between constant load and constant strain rate methods. Mater Sci Eng A2012; 532: 505–510.
35.
KarpagarajASankaranarayanasamyK. Some studies on mechanical properties and microstructural characterization of automated TIG welding of thin commercially pure titanium sheets. Mater Sci Eng A2015; 640: 180–189.
YunlianQJuDQuanH, et al.Electron beam welding, laser beam welding and gas tungsten arc welding of titanium sheet. Mater Sci Eng A2000; 280: 177–181.
39.
LeeYSKimDWLeeDY, et al.Effect of grain size on creep properties of type 316LN stainless steel. Met Mater Int2001; 7: 107–114.
40.
ElmerJW. Phase transformation dynamics during welding of Ti-6Al-4 V. J Appl Phys 2004; 95: 8327–8339.
41.
JunaidMBaigMNShamirM, et al.A comparative study of pulsed laser and pulsed TIG welding of Ti-5Al-2. 5Sn titanium alloy sheet. J Mater Process Technol2017; 242: 24–38.
42.
NosenkoVMorfillGERosakisP. Direct experimental measurement of the speed-stress relation for dislocations in a plasma crystal. Phys Rev Lett2011; 106: 1–5.
43.
ZhuLNXuBSWangHD, et al.Pileup behavior in sharp nanoindentation of AISI 1045 steel. Phys Procedia2013; 50: 214–218.
44.
HuangPWangFXuM, et al.Dependence of strain rate sensitivity upon deformed microstructures in nanocrystalline Cu. Acta Mater2010; 58: 5196–5205.
45.
CallisterWDRethwisch DG. Materials science. NJ: John Wiley & Sons, Inc., 1988. Epub ahead of print 1988. DOI: 10.1126/science.239.4836.125.
46.
LiuXZhangQZhaoX, et al.Ambient-temperature nanoindentation creep in ultrafine-grained titanium processed by ECAP. Mater Sci Eng A2016; 676: 73–79.
47.
PengHFangWDongC, et al.Nano-mechanical properties and creep behavior of Ti6Al4V fabricated by powder bed fusion electron beam additive manufacturing. Materials 2021; 14(11): 3004.
48.
BadeaLSurandMRuauJ, et al. Creep behavior of Ti-6Al-4V from 450 °C to 600 °C. UPB Scientific Bulletin, Series B 2014; 76(1): 185–196.
49.
BarbozaMJRMoura NetoCSilvaCRM. Creep mechanisms and physical modeling for Ti-6Al-4 V. Mater Sci Eng A2004; 369: 201–209.
50.
BanerjeeDWilliamsJC. Perspectives on Titanium science and technology. Acta Mater2013; 61: 844–879.
51.
WangDTanJLiCJ, et al.Enhanced creep resistance of Ti30Al25Zr25Nb20 high-entropy alloy at room temperature. J Alloys Compd2021; 885: 161038.
52.
ZhangJ-S (ed). High temperature deformation of intermetallic compounds. In: High temperature deformation and fracture of materials. Sawaston: Woodhead Publishing, 2010, pp. 111–138.
53.
KorlaRChokshiAH. A constitutive equation for grain boundary sliding: an experimental approach. Metall Mater Trans A Phys Metall Mater Sci2014; 45: 698–708.
54.
NixWDIlschnerB. Mechanisms controlling creep of single phase metals and alloys. In: HaasenPGeroldVKostorzG (eds) Strength of metals and alloys. Oxford: Pergamon, 1979, pp.1503–1530.
55.
MahmudiRGeranmayehARMahmoodiSR, et al.Room-temperature indentation creep of lead-free Sn – Bi solder alloys. J Mater Sci Mater Electron2007; 18: 1071–1078.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
