Effects of particulate reinforcements on the hardness,impact and tensile strengths of AA 6061-T6 friction stir weldments

Abstract

Due to loss of structural strengthening at temperatures beyond 250°C, heat-treated aluminium alloys (e.g. AA 6061-T6) weldments are usually characterized with poor mechanical properties including hardness, tensile and impact strengths. In this work, friction stir weldments of AA 6061-T6 reinforced with the additions of SiC, B₄C and Al₂O₃ particles at the joints were produced and investigated for improved hardness, tensile strength and impact strength over the unreinforced weldment. The results showed that the entire reinforced welded joint exhibited improved hardness because of the enhanced metal matrix grain refinement and inherent high hardness of the reinforcement particles. B₄C particle addition produced hardest joint of about 81% of the base metal hardness (∼114 HV_0.3). The impact energies of the SiC (16.9 J), B₄C (16.5) and Al₂O₃ (12.2 J) reinforced weldments are closer to that of the base metal (18.6 J) compared with the unreinforced weldment (9.6 J). The reinforced weldments showed no significant improvement over the tensile strength of the unreinforced weldment. B₄C and SiC reinforcements produced the highest improvements in the hardness (at the joint) and impact strength of the AA 6061-T6 friction stir weldments, respectively.

Keywords

Friction stir welding aluminium alloy 6061-T6 reinforcement impact strength tensile strength micro-hardness

Get full access to this article

View all access options for this article.

References

Abioye

Zuhailawati

Aizad

, et al. Geometrical, microstructural and mechanical characterization of pulse laser welded thin sheet 5052-H32 aluminium alloy for aerospace applications. Trans Nonferrous Metals Soc China 2019; 29: 667−679.

Marini

Ismail

AB.

Torsional deformation and fatigue behaviour of 6061 aluminium alloy. IIUM Eng J 2011; 12: 21–32.

Moreira

PMGP

Santos

Tavares

SMO

, et al. Mechanical and metallurgical characterization of friction stir welding joints of AA6061-T6 with AA6082-T6. Mater Des 2009; 30: 180–187.

Raturi

Garg

Bhaltacharya

Joint strength and failure studies of dissimilar AA6061-AA7075 friction stir welds: effects of tool pin, process parameters and preheating.

J Eng Fail Anal 2019; 96: 570–588.

Goyal

Rohilla

Kaushik

AK.

Effect of process parameters on the mechanical properties of friction stir welded dissimilar AA6061-T6 and AA5086-H32 aluminum alloy joints. Int J Theoret Appl Mech 2017; 12: 21–32.

Elatharasan

Senthil-Kumar

VS.

An experimental analysis and optimization of process parameter on friction stir welding of AA 6061-T6 aluminium alloy using RSM. Proc Eng 2013; 64: 1227–1234.

Banik

Roy

Barma

, et al. An experimental investigation of torque and force generation for varying tool tilt angles and their effects on microstructure and mechanical properties: friction stir welding of AA 6061-T6. J Manuf Process 2018; 31: 395–404.

Mirjavadi

Alipour

Emamiam

, et al. Inﬂuence of TiO₂ nanoparticles incorporation to friction stir welded 5083 aluminum alloy on the microstructure, mechanical properties and wear resistance. Alloys Compounds 2017; 712: 795–803.

Paidar

Ojo

Ezatpour

, et al. Influence of multi-pass FSP on the microstructure, mechanical properties and tribological characterization of Al/B₄C composite fabricated by accumulative roll bonding (ARB). Surf Coat Technol 2019; 361: 159–169.

10.

Asadi

Besharati Givi

Abrinia

, et al. Effects of SiC particle size and process parameters on the microstructure and hardness of AZ91/SiC composite layer fabricated by FSP. J Mater Eng Perform 2011; 20: 1554–1562.

11.

Vysotskiy

Malopheyev

Mironov

, et al. Effect of pre-strain path on suppression of abnormal grain growth in friction stir welded 6061 aluminium alloy. Mater Sci Eng A 2019; 760: 206–213.

12.

Jamalian

Ramezani

Ghobadi

, et al. Processing-structure-property correlation in nano-SiC-reinforced friction stir welded aluminium joints. J Manuf Process 2016; 21: 180–189.

13.

Periyasamy

Mohan

Balasubramanian

Effect of heat input on mechanical and metallurgical properties of friction stir welded AA6061-10% SiCp MMCs. J Mater Eng Perform 2012; 21: 2417–2428.

14.

Abioye

Zuhailawati

Anasyida

, et al. Investigation of the microstructure, mechanical and wear properties of AA6061-T6 friction stir weldments with different particulate reinforcements addition. J Mater Res Technol 2019; 8: 3917–3928.

15.

Maurya

Kumar

Ariharan

, et al. Effect of carbonaceous reinforcements on the mechanical and tribological properties of friction stir processed Al6061 alloy. Mater Des 2016; 9: 155–166.

16.

Abioye

Folkes

Clare

, et al. Concurrent Inconel 625 wire and WC powder laser cladding: process stability and microstructural characterisation. Surf Eng 2013; 29: 647–653.

17.

Baridula

Ibrahim

Faizal

CKM

, et al. Influence of groove size and reinforcements addition on mechanical properties and microstructure of friction stir welded joints. IOP Conf Series: Mater Sci Eng 2018; 319: 1–8.

18.

Moradi

Aval

Jamaati

Effect of pre and post welding heat treatment in SiC-fortified dissimilar AA6061-AA2024 FSW butt joint. J Manuf Process 2017; 30: 97–105.

19.

Singh

Tiwari

Shukla

DK.

Friction stir welding of AA6061-T6: the effect of Al2O3 nanoparticles addition. Results Mater 2019; 1: 1–12.

20.

Jafari

Mansouri

Honarpisheh

Investigation of residual stress distribution of dissimilar Al-7075-T6 and Al-6061-T6 in the friction stir welding process strengthened with SiO2 nanoparticles. J Manuf Process 2019; 43: 145–153.

21.

Ogedengbe

Abioye

Ekpemogu

AI.

Investigation of mechanical properties and parametric optimization of the dissimilar GTAW of AISI 304 stainless steel and low carbon steel. World J Eng 2018; 15: 584−591.