Equal channel angular rolling process is defined as a severe plastic deformation method that imposes very large plastic strain on a material in order to enhance its mechanical properties and grain structure refinement. In this study, residual stress profiles through the thickness of St12 strips that were subjected to different passes of equal channel angular rolling were investigated by slitting method. Also, the effects of different routes of equal channel angular rolling (A and C) were studied on the mechanical properties and residual stress. Furthermore, the effect of post annealing on the mechanical properties and residual stress of 4-pass equal channel angular rolled strip was examined. The results showed significant increase in the yield strength, ultimate tensile strength, and micro hardness of the samples in both routes. But the elongation decreased. Considerable magnitude of residual stress was created through the thickness of equal channel angular rolled samples such that the maximum tensile residual stress of some samples raised to about half of the corresponding yield strength. The maximum magnitude of residual stress in route C was smaller than that in route A.
SadeghiISerajzadehS. Mechanical behavior during aging of plastically deformed AA6061-SiCp composite in different temperatures. Proc IMechE, Part L: J Materials: Design and Applications2012; 226: 322–329.
2.
RosochowskiAOlejnikL. Finite element simulation of severe plastic deformation processes. Proc IMechE, Part L: J Materials: Design and Applications2007; 221: 187–196.
3.
SurendarnathSSankaranarayanasamyKRavisankarB. A comparative study of commercially pure aluminum processed by ECAP using conventional and new die. Mater Manuf Process2014; 29: 1172–1178.
4.
LarijaniNKammerhoferCEkhM. Simulation of high pressure torsion tests of pearlitic steel. J Mater Process Tech2015; 223: 337–343.
5.
SabbaghianradSLangdonTG. Developing superplasticity in an aluminum matrix composite processed by high-pressure torsion. Mat Sci Eng A-Struct2016; 655: 36–43.
6.
IsikMNiinomiMChoKet al.Microstructural evolution and mechanical properties of biomedical Co–Cr–Mo alloy subjected to high-pressure torsion. J Mech Behav Biomed2016; 59: 226–235.
7.
YuHLLuCTieuAKet al.Fabrication of nanostructured aluminum sheets using four-layer accumulative roll bonding. Mater Manuf Process2014; 29(4): 448–453.
8.
RezaeiMRToroghinejadMRAshrafizadehF. Effects of ARB and ageing processes on mechanical properties and microstructure of 6061 aluminum alloy. J Mater Process Tech2011; 211: 1184–1190.
9.
AmirkhanlouSJamaatiRNiroumandBet al.Using ARB process as a solution for dilemma of Si and SiC p distribution in cast Al–Si/SiC p composites. J Mater Process Tech2011; 211: 1159–1165.
10.
RosochowskiARodietRLipinskiPFinite element simulation of cyclic extrusion-compression. In: PietrzykMKusiakJMajtaJ (eds). Proceedings of the 8th International Conference on Metal Forming, Krakow, Poland 3–7 September 2000, pp. 253–259. Rotterdam, Brookfield: A. A. Balkema.
11.
FarshidiMHKazeminezhadM. The effects of die geometry in tube channel pressing: Severe plastic deformation. Proc IMechE, Part L: J Materials: Design and Applications2016. 230: 263–272.
12.
JafarzadehHAbriniaK. Computation on continuous grain refinement in AA1050 aluminum during repetitive tube expansion and shrinking technique. Proc IMechE, Part L: J Materials: Design and Applications2015. DOI: 10.1177/1464420715625086.
13.
YadollahpourMHosseini-ToudeshkyHKarimzadehF. The use of response surface methodology in cryrolling of ultrafine grained Al6061 to improve the mechanical properties. Proc IMechE, Part L: J Materials: Design and Applications2016; 230: 400–417.
14.
SunilBR. Repetitive corrugation and straightening of sheet metals. Mater Manuf Process2015; 30: 1262–1271.
15.
KhodabakhshiFKazeminezhadM. Differential scanning calorimetry study of constrained groove pressed low carbon steel: recovery, recrystallisation and ferrite to austenite phase transformation. Mater Sci Tech Lond2014; 30: 765–773.
16.
KhodabakhshiFAbbaszadehMMohebpourSRet al.3D finite element analysis and experimental validation of constrained groove pressing-cross route as an SPD process for sheet form metals. Int J Adv Manuf Tech2014; 73: 1291–1305.
17.
LeeJCSeokHKHanJHet al.Controlling the textures of the metal strips via the continuous confined strip shearing (C2S2) process. Mater Res Bull2001; 36: 997–1004.
18.
LeeJCSeokHKSuhJY. Microstructural evolutions of the Al strip prepared by cold rolling and continuous equal channel angular pressing. Acta Mater2002; 50: 4005–4019.
19.
HabibiAKetabchiMEskandarzadehM. Nano-grained pure copper with high-strength and high-conductivity produced by equal channel angular rolling process. J Mater Process Tech2011; 211: 1085–1090.
20.
NamCYHanJHChungYHet al.Effect of precipitates on microstructural evolution of 7050 Al alloy sheet during equal channel angular rolling. Mat Sci Eng A-Struct2003; 347: 253–257.
21.
ChengYQChenZHXiaWJ. Drawability of AZ31 magnesium alloy sheet produced by equal channel angular rolling at room temperature. Mater Charact2007; 58: 617–622.
22.
ChengYQChenZHXiaWJet al.Effect of channel clearance on crystal orientation development in AZ31 magnesium alloy sheet produced by equal channel angular rolling. J Mater Process Tech2007; 184: 97–101.
23.
HassaniFZKetabchiM. Nano grained AZ31 alloy achieved by equal channel angular rolling process. Mat Sci Eng A-Struct2011; 528: 6426–6431.
24.
AzimiATutunchilarSFarajiGet al.Mechanical properties and microstructural evolution during multi-pass ECAR of Al 1100–O alloy. Mater Des2012; 42: 388–394.
25.
HabibiAKetabchiM. Enhanced properties of nano-grained pure copper by equal channel angular rolling and post-annealing. Mater Des2012; 34: 483–487.
26.
KvačkajTKováčováAKvačkajMet al.TEM studies of structure in OFHC copper processed by equal channel angular Rolling. Micron2012; 43: 720–724.
27.
MahmoodiMSedighiMTannerDA. Investigation of through thickness residual stress distribution in equal channel angular rolled Al 5083 alloy by layer removal technique and X-ray diffraction. Mater Des2012; 40: 516–520.
28.
PrimeMB. Residual stress measurement by successive extension of a slot: the crack compliance method. Appl Mech Rev1999; 52: 75–96.
29.
PrimeMBHillMR. Residual stress, stress relief, and inhomogeneity in aluminum plate. Scripta Mater2002; 46: 77–82.
30.
RankinJEHillMRHackelLA. The effects of process variations on residual stress in laser peened 7049 T73 aluminum alloy. Mater Sci Eng A-Struct2003; 349: 279–291.
31.
Milan MT, Tarpani JR and Bose Filho WW. Slot machining effects on residual stress measurements using the crack compliance method. In: 18th International congress of mechanical engineering, Ouro Preto, MG, 6–11 November 2005.
32.
PrimeMBHillMR. Uncertainty, model error, and order selection for series-expanded, residual-stress inverse solutions. J Eng Mater Technol ASME2006; 128: 175–185.
33.
Prime MB and Pagliaro P. Uncertainty, model error, and improving the accuracy of residual stress inverse solutions. In: Proceeding of the 2006 SEM annual conference and exposition on experimental and applied mechanics, USA, 4–7 June 2006.
34.
LeeMJHillMR. Effect of strain gage length when determining residual stress by slitting. J Eng Mater Technol ASME2007; 129: 143–150.
35.
PrimeMBCraneDLSlitting method measurement of residual stress profiles, including stress discontinuities, in layered specimens. In: RossiMet al. (eds). Residual stress, thermomechanics & infrared imaging, hybrid techniques and inverse problems2014; vol. 8, , Springer international publishing, pp. 93–102.
36.
DeWaldATHillMRRepeatability of incremental hole drilling and slitting method residual stress measurements. In: RossiMet al. (eds). Residual stress, thermomechanics & infrared imaging, hybrid techniques and inverse problems2014; vol. 8, , Springer international publishing, pp. 113–118.
37.
DeplusKSimarAVan HaverWet al.Residual stresses in aluminium alloy friction stir welds. Int J Adv Manuf Tech2011; 56: 493–504.
38.
SedighiMJoudakiJKotobiM. Uncertainty of residual stresses analysis in slitting method: A case study of roll bending process. J Strain Anal Eng2015; 50: 335–343.
39.
ASTM E8/E8M-09: 2009. Standard test methods for tension testing of metallic materials. West Conshohocken, PA: ASTM International.
