An experimental investigation and optimization of friction stir welding process for AA6082 T6 (cryogenic treated and untreated) using an integrated approach of Taguchi,grey relational analysis and entropy method

Abstract

Friction stir welding is a solid state welding in which two metal parts are joined without melting with the help of frictional heat generated between the work material and non-consumable tool. Because of the poor microstructure, cracks, porosity and residual stresses in fusion welding of aircraft aluminium alloys, friction stir welding is highly attractive for joints in aircraft structures. In the present work, using Taguchi’s design of experiment method, combined effect of process parameters namely tool rotation speed, welding speed (or traverse speed of tool), tool pin profile and tool shoulder diameter have been investigated for the ultimate tensile strength and percentage elongation of friction stir welded joints of AA6082 alloy. Two similar sets of experiments were performed to prepare the friction stir welded joints; first samples of AA 6082-T6 (solution heat treated and artificially aged) were friction stir welded and second cryogenic treated AA6082 alloy were friction stir welded . A comparison in the optimal conditions of two sets of experiments has also been presented. In tempered aluminium alloy, three process parameters namely tool rotation, weld speed and tool shoulder diameter are significantly affecting ultimate tensile strength, while all four parameters are significant for percentage elongation. The influence of cryogenic treatment has also been noticed on two response characteristics. An integrated approach of Taguchi method, grey relational analysis and entropy measurement method have been utilized to obtain an optimal single setting of process parameters for two response characteristics. For the friction stir welded joint of AA6082-T6 (without cryogenic treatment), a single optimal setting of process parameters was obtained corresponding to tool rotation: 1200 r/min, weld speed: 35 mm/min, tool pin profile, threaded cylindrical and tool shoulder diameter: 16 mm. Similarly, the single optimal setting for cryogenic treated aluminium alloy (AA6082) was obtained corresponding to tool rotation: 1200 r/.min, weld speed: 35 mm/min, tool pin profile, cylindrical and tool shoulder diameter: 14 mm.

Keywords

Friction stir welding AA6082 T6 Taguchi method grey relational analysis entropy method

Get full access to this article

View all access options for this article.

References

Mishra

. Friction stir welding and processing. Mater SciEng R 2005; 50: 1–78.

Fukuda

. Friction stir welding process. Weld Int 2001; 15: 611–615.

Gemme

Verreman

Dubourg

LLM

. Numerical analysis of the dwell phase in friction stir welding and comparison with experimental data. Mater Sci Eng A 2009; 527: 4152–4160.

Rajakumar

Muralidharan

Balasubramanian

. Influence of friction stir welding process and tool parameters on strength properties of AA7075-T6 aluminium alloy joints. MaterDes 2011; 32: 535–549.

Pashazadeh

Masoumi

Teimournezhad

. A study on material flow pattern in friction stir welding using finite element method. Proc. of the IMechE, Part B: J Engineering Manufacture 2013; 227: 1453–1466.

Gheisari

Pashazadeh

Teimournezhad

. Weld defect formation in FSWed coppers. J Mater EngPerform 2014; 23: 2000–2006.

Shen

Luo

. Fabrication and anti-oxidation properties of Al/Ti-6Al-4V bimetallic clad-sheet by multi-pass friction stir welding. Proc. of the IMechE, Part B: JEngineering Manufacture 2014. (DOI: 10.1177/0954405414535583).

Deng

. Control problems of grey system. SystControl Lett 1982; 5: 288–294.

Caydas

Hascalik

. Use of the grey relational analysis to determine optimum laser cutting parameters with multi performance characteristics. Opt Laser Technol 2008; 40: 987–994.

10.

Chang

Hwang

. Grey relational analysis coupled with principal component analysis for optimization design of the cutting parameters in high-speed end milling. J. Mater Proc Technol 2009; 209: 3808–3817.

11.

Chiang

Hsieh

. The use of the Taguchi method with grey relational analysis to optimize the thin film sputtering process with multiple quality characteristics in color filter manufacturing. Comput Ind Eng 2009; 56: 648–661.

12.

Sharma

Yadava

. Optimization of cut quality characteristics during Nd: YAG laser straight cutting of Ni-Based super alloy thin sheet using grey relational analysis with entropy measurement. MaterManuf Process 2011; 26: 1522–1529.

13.

Jangra

Grover

Aggarwal

. Simultaneous optimization of material removal rate and surface roughness for WEDM of WC-Co composite using grey relational analysis along with Taguchi method. Int J Ind Eng Comput 2011; 2: 479–490.

14.

Yong

AYL

Seah

KHW

Rahman

. Performance evaluation of cryogenically treated tungsten carbide tools in turning. Int JMach ToolManuf 2006; 46: 2051–2056.

15.

ASTM Handbook. Aluminium and Magnesium Alloys. West Conshohocken: ASTM International, 2013.

16.

Roy

. A primer on Taguchi method, New York: Van Nostrand Reinhold, 1990.

17.

Roy

. Design of experiments using the Taguchi approach: 16 steps to product and process improvement, New York: Wiley- Interscience, 2001, pp. 179–179.

18.

Deng

. Introduction to grey system. J Grey Syst 1989; 1: 1–24.

19.

Singh

Yadava Vand Kumar

. Diamond face grinding of WC-Co composite with spark assistance: experimental study and parameter optimization. Int J Precis Eng Manuf 2010; 11: 509–518.

20.

Rao

Yadava

. Multi-objective optimization of Nd:YAG laser cutting of thin super alloy sheet using grey relational analysis with entropy measurement. Opt Laser Technol 2009; 41: 922–930.

21.

HuUzun

Donne

Argagnotto

. Friction stir welding of dissimilar Al 6013-T4 To X5CrNi18-10 stainless steel. MaterDes 2005; 26: 41–46.

22.

Zhang

Lin

. Defects formation procedure and mathematic model for defect free friction stir welding of magnesium alloy. MaterDes 2006; 27: 805–809.

23.

Zhang

. Material behaviors and mechanical features in friction stir welding process. Int J Adv Manuf Technol 2007; 35: 86–100.

24.

Zhang

Chen

. 3D modeling of material flow in friction stir welding under different process parameters. J Mater Process Technol 2007; 183: 62–70.

25.

Kulekci

Şik

Kaluç

. Effects of tool rotation and pin diameter on fatigue properties of friction stir welded lap joints. Int J Adv Manuf Technol 2008; 36: 877–882.

26.

Kumbhar

Bhanumurthy

. Friction stir welding of Al 6061 alloy. Asian J. Exp. Sci 2008; 22: 63–74.

27.

Elangovan

Balasubramanian

Valliappan

. Influences of tool pin profile and axial force on the formation of friction stir processing zone in AA6061 aluminium alloy. Int J Adv Manuf Technol 2008; 38: 285–295.

28.

Zhang

Liu

Chen

. Effect of shoulder size on the temperature rise and the material deformation in friction stir welding. Int J Adv Manuf Technol 2009; 45: 889–895.

29.

Sakthivel

Sengar

Mukhopadhyay

. Effect of welding speed on microstructure and mechanical properties of friction-stir-welded aluminium. Int J Adv Manuf Technol 2009; 43: 468–473.

30.

Sarsýlmaz

Çaydas

. Statistical analysis on mechanical properties of friction-stir-welded AA 1050/AA 5083 couples. Int J Adv Manuf Technol 2009; 43: 248–255.

31.

Sahin

. Joining of stainless-steel and aluminium materials by friction welding. Int J Adv Manuf Technol 2009; 41: 487–497.

32.

Fratini

Buffa

Shivpuri

. In- process heat treatments to improve FS-welded butt joints. Int J Adv Manuf Technol 2009; 43: 664–670.

33.

Lakshminarayanan

Balasubramanian

Elangovan

. Effect of welding processes on tensile properties of AA6061 aluminium alloy joints. Int J Adv Manuf Technol 2009; 40: 286–296.

34.

Karthikeyan

Balasubramanian

. Predictions of the optimized friction stir spot welding process parameters for joining AA2024 aluminium alloy using RSM. Int J Adv Manuf Technol 2010; 51: 173–183.

35.

Arora

Pandey

Schape

Kumar

. Effect of process parameters on friction stir welding of aluminium alloy 2219-T87. Int J Adv Manuf Technol 2010; 50: 941–952.

36.

Padmanaban

Balasubramanian

. An experimental investigation on friction stir welding of AZ31B magnesium alloy. Int J Adv Manuf Technol 2010; 49: 111–121.

37.

Wen

Chang

. The grey entropy and its application in weighting analysis. Proc IEEE Int Conf Syst: Man Cybernet 1998; 2: 1842–1844.