Sage Journals: Discover world-class research

Abstract

Risk assessment studies for hazardous material packages require fire response prediction tools that are both accurate and rapid. This article describes the theoretically based, semiempirical reaction chemistry and radiation heat transfer models for large, optically dense pool fires incorporated in the ISIS-3D CFD software. The chemistry model employs four separate reactions (two produce radiating soot). The heat transfer model divides the computational domain into the diffusely radiative fire and its nonparticipating environment. ISIS-3D simulations are performed on a 6-m square JP8 pool fire experiment in which the soot temperature and volume fraction are measured. The reaction rate and soot formation parameters of the chemistry model are determined based on a comparison of the simulation with the measured data. Simulations are then performed on an experiment that measures the temperature of a pipe calorimeter suspended over the leeside of a 19-m-diameter JP8 fuel pool fire with a 9.5 m/s crosswind. The soot volume fraction that the heat transfer model uses to define the edge of the diffusely radiating fire is determined based on a comparison with the measured average temperature of the calorimeter. That simulation accurately predicts the calorimeter spatial temperature variation without further adjustment. ISIS-3D is not fully predictive, should not be used far outside the range of conditions in which its parameters are determined (JP8 pool fires larger than 2 m), and is not intended to replace the fundamental fire physics software. However, it demonstrates highly accurate results with rapid turnaround times for a range of conditions that are relevant to large hazardous material transport packages in severe fire conditions.

Keywords

risk assessment radiation heat transfer combustion chemistry pool fire fire simulation

Get full access to this article

View all access options for this article.

References

Fischer, L.E. , Chou, C.K. , Gerhard, M.A. , Kimura, C.Y. , Martin, R.W. , Mensing, R.W. , Mount, M.E. and Witte, M.C. , “Shipping Container Response to Severe Highway and Railway Accident Conditions,” NUREG/CR4829, 1987.

U.S. Nuclear Regulatory Commission , “Packaging and Transportation of Radioactive Material,” Rules and Regulations, Title 10, Part 71, Code of Federal Regulations, 2000.

Lopez, A.R. , Gritzo, L.A. and Sherman, M.P. , “Risk Assessment Compatible Fire Models (RACFMs),” Sandia Report SAND97-1562, July 1998.

Murphy, J.J. and Shaddix, C.R. , “Soot Properties and Species Measurements in a Two-Meter Diameter JP-8 Pool Fire: 2003 Test Series,” Sandia Report Sand2004-8085, March 2004.

Lopez, C. , Koski, J.A. and Suo-Anttila, A. , “Development and Use of the CAFE-3D Code for Analysis of Radioactive Material Packages in Fire Environment,” In: Presented at the 44th International Nuclear Material Management (INMM) Conference, 2003.

Suo-Anttila, A.J. , Koski, J.A. and Gritzo, L.A. , “CAFE: A Computer Tool for Accurate Simulation of the Regulatory Pool Fire Environment for Type B Packages,” SAND99-0625C, March 1999.

Are, N. , Greiner, M. and Suo-Anttila, A. , “Benchmark of a Fast Running Computational Tool for Analysis of Massive Radioactive Material Packages in Fire Environments,” to appear in ASME J. of Pressure Vessel Technology, 2005.

Greiner, M. and Suo-Anttila, A. , “Validation of the ISIS Computer Code for Simulating Large Pool Fires Under a Variety of Wind Conditions,” ASME J. Pressure Vessel Technology, Vol. 126, 2004, pp. 360–368 .

Suo-Anttila, A. , F2D Users Manual: A Two-Dimensional Compressible Gas Flow Code, Sandia National Laboratories Report, SAND92-7343, June 1993.

10.

Issa, R.I. , “Solution of the Implicitly Discretised Fluid Flow Equations by Operator Splitting,” J. Comput. Phys., Vol. 62, 1985, pp. 40–65 .

11.

Smagorinsky, J. , “General Circulation Experiments with the Primitive Equations,” Monthly Weather Review, Vol. 91, 1963, pp. 99–165 .

12.

Ferzinger, J.H. , “Subgrid-Scale Modeling,” In: Galperin, B. and Orszag, S.A. eds., Large Eddy Simulations of Complex Engineering and Geophysical Flows, Cambridge University Press, Cambridge , 1993, pp. 37–54.

13.

Hirt, C.W. and Sicilian, J.M. , “A Porosity Technique for the Definition of Obstacles in Rectangular Cell Meshes,” In: 4th International Conference on Ship Hydrodynamics Washington, DC, September 1985.

14.

Modest, M.F. , Radiative Heat Transfer, 2nd ed., Academic Press, New York , 2003.

15.

Siegel, R. and Howell, J.R. , Thermal Radiation Heat Transfer, Hemisphere Publishing Corporation, New York , 1981.

16.

Said, R. , Garo, A. and Borghi, R. , “Soot Formation Modeling for Turbulent Flames,” Combustion and Flame, Vol. 108, 1997, pp. 71–86 .

17.

Gritzo, L.A. , Sivathaunu, Y.R. and Gill, W. , “Transient Measurements of Radiative Properties, Soot Volume Fraction, and Soot Temperature in a Large Pool Fire,” Combustion Science and Technology, Vol. 139, 1998, pp. 113–136 .

18.

Suo-Anttila, J.M. and Gritzo, L.A. , “Thermal Measurements from a Series of Tests with a Large Cylindrical Calorimeter on the Leeward Edge of a JP-8 Pool Fire in Crossflow,” Sandia National Laboratories Report, SAND2001-1986, June 2001.

19.

Gritzo, L.A. , Moya, J.A. and Murray, D. , “Fire Characterization and Object Thermal Response for a Large Flat Plate Adjacent to a Large JP4 Fuel Fire,” Sandia National Laboratories Report SAND97-0047, 1997, p. 22-22.

20.

Greiner, M. , Shin, S. , Faulkner, R.J. and Wirtz, R.A. , “Transport Cask Response to Regulatory Format Thermal Events, Part 1: Rail Package,” International J. of Radioactive Material Transport, Vol. 9, No. 3, 1998, pp. 187–192 .

21.

Greiner, M. , Faulkner, R.J. and Jin, Y.Y. , “Transport Cask Response to Regulatory Format Thermal Events, Part 2: Truck Cask,” International J. of Radioactive Material Transport, Vol. 9, No. 3, 1998, pp. 193–198 .

Radiation Heat Transfer and Reaction Chemistry Models for Risk Assessment Compatible Fire Simulations

Abstract

Keywords

Get full access to this article

References