An ultrasonic sensor for monitoring wheel flange/rail gauge corner contact

Abstract

Wheel/rail contact is critical to the successful operation of a railway network. Contact occurs at the wheel tread/rail head and wheel flange/rail gauge corner. Contact conditions are more severe in the latter, which occurs mainly at curves. The contact is small and supports large loads; therefore, high contact stresses are generated. These, combined with the slip in the contact, are primarily responsible for driving the processes that lead to wheel and rail damage, whether by deformation, wear or a fatigue process. Multi-body dynamics software is useful for predicting the wheel/rail contact characteristics; however, there is a shortage of experimental tools available. In this study, the feasibility of an approach based on an ultrasonic sensor mounted on the wheel is investigated. The sensor emits an ultrasonic pulse which is designed to impinge on the wheel flange. If there is no contact the pulse is fully reflected back at the flange and picked up by the same sensor. If flange contact takes place, a proportion of the pulse amplitude will be transmitted into the rail. The signal reflected back to the sensor is therefore reduced. The amount by which this signal reduces indicates how much flange contact has occurred. This work had two aspects. First, a standard ultrasonic ray-tracing software package was used to establish what it is possible to measure with sensors mounted in the wheel and to determine the best location and orientation. The second aspect was an experimental study to determine whether such measurements are feasible. Test specimens were cut from sections of wheel and rail, and a 2 MHz ultrasonic contact transducer was bonded onto the wheel in a position best suited to detect the flange contact. The specimens were pressed together in a bi-axial loading frame to generate differing degrees of rail head and flange contact. The reflected signal was monitored as the normal and lateral loads were varied. It proved possible not only to detect the onset of flanging, but also to record a signal that varied monotonically with both normal and lateral applied load. A map of reflected ultrasound against the applied loading is presented. The technology, while not currently suitable for full field implementation could be very useful in laboratory studies on, for example, a full-scale wheel/rail rig.

Keywords

Wheel/rail contact ultrasonic measurement ultrasonic reflection flange contact

Get full access to this article

View all access options for this article.

References

Cannon

Pradier

. Rail rolling contact fatigue - research by the European Rail Research Institute. Wear 1996; 191: l–13.

Kalker

. Fast algorithm for the simplified theory of rolling contact. Veh Syst Dyn 1982; 11: 1–13.

Kalker

. Three-dimensional elastic bodies in rolling contact , Dordrecht, The Netherlands: Kluwer, 1990.

Telliskivi

Olofsson

. Contact mechanics analysis of measured wheel-rail profiles using the finite element method. Proc IMechE, Part F: J Rail Rapid Transit 2001; 215: 65–72.

Pau

Aymerich

Ginesu

. Measurements of nominal contact area in metallic surfaces: a comparison between an ultrasonic method and a pressure sensitive film. Wear 2001; 249: 533–535.

Poole W. The measurement of contact area between opaque objects under static and dynamic rolling conditions. In: The conference on contact mechanics and wear of the wheel/rail system, University of Rhode Island, Kingston, RI, 1987, pp.59–72. Waterloo, Ontario: Waterlooville Press.

Marshall

Lewis

Dwyer-Joyce

. Experimental characterisation of wheel-rail contact patch evolution. Trans ASME, J Tribol 2006; 128(3): 493–504.

Marshall

Lewis

Drinkwater

Dwyer-Joyce

. An approach for contact stress mapping in joints and concentrated contacts. J Strain Anal Engng Des 2004; 39(4): 339–350.

Pau

Aymerich

Ginesu

. Ultrasonic measurement of nominal contact area and contact pressure in a wheel/rail system. Proc IMechE, Part F: J Rail Rapid Transit 2000; 214: 231–243.

10.

Pau

Aymerich

Ginesu

. Distribution of contact pressure in wheel–rail contact area. Wear 2002; 253: 265–274.

11.

Drinkwater

Castaings

Hosten

. The measurement of A and S Lamb wave attenuation to determine the normal and shear stiffnesses of a compressively loaded interface. J Acoust Soc Am 2003; 113: 3161–3170.

12.

Dwyer-Joyce

Yao

Zhang

. Feasibility study for real time measurement of wheel/rail contact using an ultrasonic array. Trans ASME, J Tribol 2009; 131(4): ). DOI: 10.1115/1.3176992.

13.

Marshall

Lewis

Dwyer-Joyce

. Ultrasonic measurement of railway wheel hub/axle press-fit contact pressures. Proc IMechE, Part F: J Rail Rapid Transit 2011; 225(3): 1067–1078.

14.

Stock

Eadie

Elvidge

Oldknow

. Influencing rolling contact fatigue through top of rail friction modifier application – a full scale wheel-rail test rig study. Wear 2011; 271: 134–142.