Increasing the efficiency of perovskite solar cells using Cs 4 CuSb 2 Cl 12 quantum dots as an interface layer: A numerical study

Abstract

Recently, the advantages of perovskite solar cells (PSCs) and a significant increase in power conversion efficiency (PCE) have played an essential role in the preference for these materials. Although different methods are used to increase PCE and reduce losses at the interfaces in PSCs, placing a new layer between the absorber/hole transfer layer (HTL) or between the absorber/electron transfer layer (ETL) stands out as one of the most common methods. In this study, considering stability, sustainability, mobility, and non-toxicity, Cs₄CuSb₂Cl₁₂ (CCSC) perovskite quantum dots (PQDs) were preferred as the interface layer between absorber and HTL in CsPbI₃ and formamidinium lead iodide (FAPI)-based PSC devices. While SnO₂, Cu₂O, and nickel were used as ETL, HTL, and back contact, respectively, CsPbI₃ and FAPI perovskites were utilized as absorber materials separately. Simulations were conducted on Solar Cell Capacitance Simulator (SCAPS-1D) software and the current density (J) and voltage characteristics were compared. By choosing different interface layer thicknesses, different radiative recombination coefficients (RRCs), and different defect sites, the cell efficiency of the PQD interlayer solar cells were simulated. Simulations were also carried out using different series resistance (R_s) and different shunt resistance (R_sh) values to show the effect of parasitic losses on cell efficiency, and it was observed that device efficiency increased where R_s was low and R_sh was high. In addition, in FAPI-based structure, with the addition of a PQD layer between the absorber and HTL, it was observed that the short circuit current density increased from 17.6 mA/cm² to 25.67 mA/cm², while the cell efficiency increased by 30%. Furthermore, according to the results obtained using CsPbI₃ as an absorber, adding a PQD layer between CsPbI₃ and HTL increased the short circuit current density from 17.8 mA/cm² to 20.7 mA/cm² and cell efficiency by 16%. To sum up, these simulation results demonstrate that inserting a PQD layer between the absorber and HTL significantly enhances the efficiency and charge carrier capacity of solar cells.

Keywords

Solar cells perovskite quantum dots interfacial layer SCAPS-1D solar cell efficiency

Get full access to this article

View all access options for this article.

References

Jeong,

Choi

. Stable perovskite solar cells with efficiency exceeding 24.8% and 0.3-V voltage loss. Sci 2020; 369: 1615–1620.

Kojima

Teshima

Shirai

, et al. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells. J Am Chem Soc 2009; 131: 6050–6051.

Chen

Baek

Hou

, et al. Enhanced optical path and electron diffusion length enable high-efficiency perovskite tandems. Nat Commun 2020; 11: 1–9.

Green

Ho-Baillie

Snaith

. The emergence of perovskite solar cells. Nat Photonics 2014; 8: 506–514.

Kim

Lee

C-R

, et al. Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%. Sci Rep 2012; 2: 1–7.

Park

. Perovskite solar cells: an emerging photovoltaic technology. Mater Today 2015; 18: 65–72.

Alharbi

Alyamani

Kubicki

, et al. Atomic-level passivation mechanism of ammonium salts enabling highly efficient perovskite solar cells. Nat Commun 2019; 10: 1–9.

Cho

Soufiani

Yun

, et al. Mixed 3D–2D passivation treatment for mixed-cation lead mixed-halide perovskite solar cells for higher efficiency and better stability. Adv Energy Mater 2018; 8: 1703392.

Cho

, et al. Highly efficient perovskite solar cells with a compositionally engineered perovskite/hole transporting material interface. Energy Environ Sci 2017; 10: 621–627.

10.

Zhang

, et al. Bifunctional alkyl chain barriers for efficient perovskite solar cells. Chem Commun 2015; 51: 7047–7050.

11.

Chen

, et al. Hybrid interfacial layer leads to solid performance improvement of inverted perovskite solar cells. Energy Environ Sci 2015; 8: 629–640.

12.

Guo

, et al. Multifunctional MgO layer in perovskite solar cells. ChemPhysChem 2015; 16: 1727–1732.

13.

, et al. Recent advances in interfacial engineering of perovskite solar cells. J Phys D Appl Phys 2017; 50: 373002.

14.

, et al. A chemically inert bismuth interlayer enhances long-term stability of inverted perovskite solar cells. Nat Commun 2019; 10: 1–11.

15.

, et al. Efficient and low-temperature processed perovskite solar cells based on a cross-linkable hybrid interlayer. J Mater Chem A 2015; 3: 18483–18491.

16.

Liu

, et al. Fine-tuning optical and electronic properties of graphene oxide for highly efficient perovskite solar cells. Nanoscale 2015; 7: 10708–10718.

17.

Niu

, et al. Study on the stability of CH₃NH₃PbI₃ films and the effect of post-modification by aluminum oxide in all-solid-state hybrid solar cells. J Mater Chem A 2013; 2: 705–710.

18.

Wen

, et al. Interfacial engineering with amino-functionalized graphene for efficient perovskite solar cells. J Mater Chem A 2016; 4: 13482–13487.

19.

Cao

, et al. Thiols as interfacial modifiers to enhance the performance and stability of perovskite solar cells. Nanoscale 2015; 7: 9443–9447.

20.

Zhu

, et al. Efficiency enhancement of perovskite solar cells through fast electron extraction: the role of graphene quantum dots. J Am Chem Soc 2014; 136: 3760–3763.

21.

, et al. Carbon quantum dots/TiOx electron transport layer boosts efficiency of planar heterojunction perovskite solar cells to 19%. Nano Lett 2017; 17: 2328–2335.

22.

, et al. 9.13%-Efficiency And stable inorganic CsPbBr₃ solar cells. Lead-free CsSnBr₃-xIx quantum dots promote charge extraction. J Power Sources 2018; 399: 76–82.

23.

Liu

, et al. Efficiency and stability enhancement of perovskite solar cells by introducing CsPbI₃ quantum dots as an interface engineering layer. NPG Asia Mater 2018; 10: 552–561.

24.

Akin

, et al. Cesiumlead based inorganic perovskite quantum-dots as interfacial layer for highly stable perovskite solar cells with exceeding 21% efficiency. Nano Energy 2019; 60: 557–566.

25.

Wang

, et al. The top-down synthesis of single-layered Cs₄CuSb₂Cl₁₂ halide perovskite nanocrystals for photoelectrochemical application. Nanoscale 2019; 11: 5180–5187.

26.

Ashitha

Joshi

Verma

, et al. Layered Cs₄CuSb₂Cl₁₂ nanocrystals for sunlight-driven photocatalytic degradation of pollutants. ACS Appl Nano Mater 2021; 4: 1305–1313.

27.

Cai

, et al. Lead-Free Cs₄CuSb₂Cl₁₂ layered double perovskite nanocrystals. J Am Chem Soc 2020; 142: 11927–11936.

28.

Burgelman

Nollet

Degrave

. Modelling polycrystalline semiconductor solar cells. Thin Solid Films 2000; 361–362: 527–532.

29.

Jiang

, et al. Sno2: a wonderful electron transport layer for perovskite solar cells. Small 2018; 14: 1801154.

30.

, et al. Design and numerical investigation of a lead-free inorganic layered double perovskite Cs₄CuSb₂Cl₁₂ nanocrystal solar cell by SCAPS-1D. Nanomater 2021; 11: 2321.

31.

Chatterjee

Pal

. Introducing Cu₂O thin films as a hole-transport layer in efficient planar perovskite solar cell structures. J Phys Chem C 2016; 120: 1428–1437.

32.

Lin

, et al. Simulated development and optimized performance of CsPbI3 based all-inorganic perovskite solar cells. Sol Energy 2020; 198: 454–460.

33.

Karthick

Bouclé

Velumani

. ‘Effect of bismuth iodide (BiI₃) interfacial layer with different HTL’s in FAPI based perovskite solar cell–SCAPS–1D study’. Sol Energy 2021; 218: 157–168.

34.

Patel

. Device simulation of highly efficient eco-friendly CH₃NH₃SnI₃ perovskite solar cell. Sci Rep 2021; 11: 1–11.

35.

Schlangenotto

Maeder

Gerlach

. Temperature dependence of the radiative recombination coefficient in silicon. Phys status Solidi 1974; 21: 357–367.

36.

Tvingstedt

, et al. Removing leakage and surface recombination in planar perovskite solar cells. ACS Energy Lett 2017; 2: 424–430.

37.

Singh

Sandhu

Lee

. Elucidating the effect of shunt losses on the performance of mesoporous perovskite solar cells. Sol Energy 2019; 193: 956–961.