Non periodic motion has been investigated using power spectrum analysis of Fast Fourier Transform (FFT), Lyapunov exponent parameter using Wolf algorithm, and Phase-plane mapping. A multi degrees of freedom (spring-damper system) are added at the end of the follower stem to reduce the nonlinear dynamic behavior of the follower. In the experiment setup, data acquisition technique with signal processing approach is used through an infrared camera device to capture the nonlinear dynamic movement of the follower. A numerical simulation is done using SolidWorks software. An OPTOTRAK/3020 with an infrared camera device is used to track the follower position experimentally. The peak of nonlinear response of the roller follower is reduced by (20.89%, 47.76%, 58.2%, and 67.16%) after using multi degrees of freedom systems.
Tas,canS.Effect of eccentricity on the speed fluctuation of cam mechanisms with translating followers. J Mech Trans Autom1988; 110: 11–15.
2.
Hwa KuangJDer LinAYow HoT.Dynamic responses of a globoidal cam system. J Mech Des2004; 126: 909–905.
3.
Hwa KuangJMing HsuCChe HuC.Dynamic behavior of globoidal cam systems with torque compensation mechanisms. J Mech Mach Theory2010; 45: 1201–1214.
4.
TsayDMHoHCWangKC.Design of torque balancing cams for globoidal cam indexing mechanisms. J Mech Des2002; 124: 441–447.
5.
RaoSSGavaneSS.Analysis and synthesis of mechanical error in cam-follower systems. J Mech Des1982; 104: 52–62.
6.
ChiuHOzakiHSatoE, et al. An analysis using offset curves for profiles, manufacturing and errors of plane cams. Int J Ser C Dyn Control Robot Des Manuf1993; 36: 110–118.
7.
AngelesJSahaSKLóPez-CajúNCS.The design of cam mechanisms with translating flat-face followers under curvature constraints. J Mech Des1994; 116: 306–310.
8.
AngelesJSahaSKLóPez-CajúNCS, et al. The design optimization of cam mechanisms with oscillating flat-face followers under curvature constraints. J Mech Des1994; 116: 311–314.
9.
GeRWangJZhangC. Model and simulation of globoidal cam mechanisms with oscillating and dual stopping followers. In: EDP conference on mechanical, aeronautical and automotive engineering, Malacca, Malaysia, 25–27 February 2017, pp.04005, 108, paper no. ICMAA 2017. France: EDP Sciences Publisher.
10.
AlzateRDi BernardoMMontanaroU, et al. Experimental and numerical verification of bifurcations and chaos in cam-follower impacting systems. Nonlinear Dyn2007; 50: 409–429.
11.
DasGuptaAGhoshA.On the determination of basic dimensions of a cam with a translating roller-follower. J Mech Des2004; 126: 143–147.
12.
LuNRenXMJiangTD, et al. Impulsive control of a cam-follower oblique-impact system. J Mech2018; 34: 475–482.
13.
YousufLS.Experimental and simulation investigation of nonlinear dynamic behavior of a polydyne cam and roller follower mechanism. J Mech Syst Signal Process2019; 116: 293–309.
14.
YousufLSDriraA. Nonlinear dynamic analysis of a polydyne cam with translated roller follower mechanism with clearance. In: ASME conference on dynamic systems and control, Atlanta, Georgia, 30 September–3 October 2018, pp.V002T24A001, paper no. DSCC2018-8901. New York: ASME Publisher.
15.
FelszeghySF.Steady-state residual vibrations in high-speed, dwell-type, rotating disk cam-follower systems. J Vib Acoust2005; 127: 12–17.
16.
YousufLSMarghituDB.Nonlinear dynamics behavior of cam-follower system using concave curvatures profile. J Adv Mech Eng2020; 12(9): 1–13.
17.
YousufLSMarghituDB.Analytic and numerical results of a disc cam bending with a roller follower. SN Appl Sci2020; 2: 1–15.
18.
ShakoorMM.Fatigue life investigation for cams with translating roller-follower and translating flat-face follower systems. Ph.D. Dissertation, Iowa State University, USA, 2006.
19.
HamzaFAbderazekHLakhdarS, et al. Optimum design of cam-roller follower mechanism using a new evolutionary algorithm. Int J Adv Manuf Technol2018; 99: 1267–1282.
20.
YousufLSMarghituDB. Non-linear dynamic analysis of a cam with flat-faced follower linkage mechanism. In: ASME 2017 international mechanical engineering congress and exposition, Tampa, FL, 3–9 November 2017, pp.V04AT051, paper no. IMECE2017-71399. New York: ASME Publisher.
SlocumAH.Precision machine design. Illustrated ed. USA: Society of Manufacturing Engineers, 1992, p.24.
23.
GheadniaHCermikOMarghituDB.Experimental and theoretical analysis of the elasto-plastic oblique impact of a rod with a flat. Int J Impact Eng2015; 86: 307–317.
24.
PlanchardDC.SolidWorks 2016 reference guide. New ed.USA: SDC Publisher, 2015.
25.
RothbartH.Cam design handbook. Vol. 394, 1st ed. New York, USA: McGraw-Hill, 2004.
26.
Abu-MahfouzI. Experimental investigation of non-linear behavior of a cam-follower mechanism. In: SEM annual conference and exposition on experimental and applied mechanics, School of Science, Engineering and Technology. Harrisburg, Penn State, USA. Vol. 3, Springfield, MA, USA, 3–6 June 2007, pp.1930–1936.
27.
ParlitzU.Estimating Lyapunov exponents from time series. Vol. 915, 1st ed. Berlin, Heidelberg: Springer, 2016.
28.
YousufLS.Investigation of chaos in a polydyne cam with flat-faced follower mechanism. J King Saud Univ Eng Sci2020; pp.1–10.
29.
StoicaPRandolphM.Spectral analysis of signals. Vol. 452, 1st ed. New Jersey, USA: Prentice Hall, 2005.
30.
GhayeshMHAmabiliM.Steady-state transverse response of an axially moving beam with time-dependent axial speed. Int J Nonlinear Mech2013; 49: 40–49.
31.
KazemiradSGhayeshMHAmabiliM.Thermo-mechanical nonlinear dynamics of a buckled axially moving beam. Arch Appl Mech2013; 83: 25–42.
32.
GhayeshMHAmabiliM.Nonlinear dynamics of an axially moving Timoshenko beam with an internal resonance. Nonlinear Dyn2013; 73: 39–52.
33.
GhayeshMHPaïdoussisMPModarres SadeghiY.Three-dimensional dynamics of a fluid-conveying cantilevered pipe fitted with an additional spring-support and an end-mass. J Sound Vib2011; 330: 2869–2899.
