This study reports an optimization of finish turning of hardened AISI D6 (60 HRC) cold work tool steel with ceramic and cubic boron nitride cutting tools using grey relational analysis. Optimization of the process parameters was performed using quality characteristics, i.e. tool wear, surface roughness, machining force and specific cutting force. Analysis of variance was used for observing the most influencing machining parameters on the quality characteristics. Evaluation of tool wear type and wear mechanism was done by tool makers’ microscope and scanning electron microscope analysis. The optimal process parameters were calculated using grey relation grade and confirmation test was performed. Based on analysis of variance results, the feed rate is the most significant controllable machining factor for the finish hard turning of AISI D6 according to the quality characteristics. Flank and crater wears were the prominent wear types on the ceramic and cubic boron nitride inserts. Grey relational analysis was successfully applied on optimization of high-speed finish hard turning of hardened AISI D6 using multi-performance characteristics.
TosunNPihtilliH. Grey relational analysis of performance characteristics in MQL milling of 7075 Al alloy. Int J Adv Manuf Technol2010; 46: 509–515.
2.
TzengCJLinYHYangYK. Optimization of turning operations with multiple performance characteristics using the Taguchi method and grey relational analysis. J Mater Process Technol2009; 209: 2753–2759.
3.
PaulachonGMoisanAJawahirIS. Tool-wear mechanisms in hard turning with polycrystalline cubic boron nitride tools. Wear2001; 250: 576–586.
4.
GopalsamyBMMondalBGhoshS. Optimization of machining parameters for hard machining: grey relational theory approach and ANOVA. Int J Adv Manuf Technol2009; 45: 1068–1086.
5.
AslanECamuscuNBirgorenB. Design optimization of cutting parameters when turning hardened AISI 4140 steel (63 HRC) with Al2O3+TiCN mixed ceramic tool. Mater Des2007; 28: 1618–1622.
6.
GologluCSakaryaN. The effects of cutter path strategies on surface roughness of pocket milling of 1.2738 steel based on Taguchi method. J Mater Process Technol2008; 206: 7–15.
7.
ThakurDRamamoorthyBVijayaraghavanL. Optimization of high speed turning parameters of superalloy Inconel 718 material using Taguchi technique. Indian J Eng Mater Sci2009; 16: 44–50.
8.
GünayMTurgutYKaçalA. Optimization of machining parameters in milling of Ti-6Al-4V alloy using Taguchi method. J New World Sci Acad Eng Sci2011; 6(1): 428–440.
9.
KacalAGulesinM. Determination of optimal cutting conditions in finish turning of austempered ductile iron using Taguchi design method. J Sci Ind Res2011; 70: 278–283.
10.
HuangJTLinJL. Optimization of machining parameters setting of die-sinking EDM process based on the grey relational analysis with L18 orthogonal array. J Technol2002; 17: 659–664.
11.
LuHSChangCKHwangNC. Grey relational analysis coupled with principal component analysis for optimization design of the cutting parameters in high-speed end milling. J Mater Process Technol2009; 209: 3808–3817.
12.
ChiangKTChangFP. Optimization of the WEDM process of particle-reinforced material with multiple performance characteristics using grey relational analysis. J Mater Process Technol2006; 108: 96–101.
13.
TosunN. Determination of optimum parameters for multi performance characteristics in drilling by using grey relational analysis. Int J Adv Manuf Technol2006; 28: 450–455.
14.
ChouYKSongH. Tool node radius effects on finish hard turning. J Mater Process Technol2004; 148: 259–268.
15.
PaulachonGBandyopadhyayBPJawahirIS. Wear behaviour of CBN tools while turning various hardened steels. Wear2004; 256: 302–310.
16.
MoreASJiangWBrownWD. Tool wear and machining performance of cBN-TiN coated carbide inserts and PCBN compact inserts in turning AISI 4340 hardened steel. J Mater Process Technol2006; 180: 253–262.
17.
GrzesikW. Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tolls. Wear2008; 265: 327–335.
18.
Derakhshan ED and Akbari AA. Experimental investigation on the effect of workpiece hardness and cutting speed on surface roughness in hard turning with CBN tools. In: Proceedings of the world congress on engineering, Vol. 2, London, UK, 1–3 July 2009.
19.
TamizharasanTSelvarajTNoorul HaqA. Analysis of tool wear and surface finish in hard turning. Int J Adv Manuf Technol2006; 28: 671–679.
20.
HorngJTLiuNMChiangKT. Investigating the machinability evaluation of Hadfield steel in the hard turning with Al2O3/TiC mixed ceramic tool based an the response surface methodology. J Mater Process Technol2008; 208: 532–541.
21.
MahfoudiFListGMolinariA. High speed turning for hard material with PCBN inserts: tool wear analysis. Int J Mach Mach Mater2008; 3(1–2): 62–79.
22.
ThakurDGRamamoorthyBVijayaraghavanL. Machinability investigation of Inconel 718 in high speed turning. Int J Adv Manuf Technol2009; 45: 421–429.
23.
UmerUButtSIAskariSJ. Comparative analyses for different modeling methods in high speed turning operations for hardened steel. J Mech Eng2008; 54(12): 850–854.
24.
SaiWB. An investigation of tool wear in high speed turning of AISI 4340 steel. Int J Adv Manuf Technol2005; 26: 330–334.
25.
PawadeRSJoshiSSBrahmankarPK. Effect of machining parameters and cutting edge geometry on surface integrity of high sped turned Inconel 718. Int J Mach Tools Manuf2008; 48: 15–28.
26.
FangWWuQ. A comparative study of the cutting forces in high speed machining of Ti-6Al-4V and Inconel 718 with a round cutting edge tool. J Mater Process Technol2009; 209: 4385–4389.
27.
ChouYKEvansCJBarashMM. Experimental investigation on CBN turning of hardened AISI 52100 steel. J Mater Process Technol2002; 124: 274–283.
28.
DinizAEOliveiraAJ. Hard turning of interrupted surfaces using CBN tools. J Mater Process Technol2008; 195: 275–281.
29.
ÖzelTKarpatYFigueiraL. Modelling of surface finish and tool flank wear in turning of AISI D2 steel with ceramic wiper inserts. J Mater Process Technol2007; 189: 192–198.
30.
GaitondeVNKarnıkSRFigueiraL. Analysis of machinability during hard turning of cold work tool steel (Type: AISI D2). Mater Manuf Processes2009; 24: 1373–1382.
31.
LimaJGAvilaRFAbraoAM. Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel. J Mater Process Technol2005; 169: 388–395.
32.
DavimJPFigueiraL. Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques. Mater Des2007; 28: 1186–1191.
33.
DavimJPMaranhaoCFariaP. Precision radial turning of AISI D2 steel. Int J Adv Manuf Technol2009; 42: 842–849.
34.
ÇakırMCEnsarioğluCDemirayakI. Mathematical modeling of surface roughness for evaluating the effects of cutting parameters and coating and coating material. J Mater Process Technol2009; 209: 102–109.
35.
IşıkY. Investigating the machinability of tool steels in turning operations. Mater Des2007; 28: 1417–1424.
36.
HuangYLiangSY. Force modeling in shallow cuts with large negative rake angle and large node radius tools-application to hard turning. Int J Adv Manuf Technol2003; 22: 626–632.
37.
ZhouJMWalterHAnderssonM. Effect of chamfer angle on wear of PCBN cutting tool. Int J Mach Tools Manuf2003; 43: 301–305.
38.
KundrakJKarpuschewskiBGyaniK. Accuracy of hard turning. J Mater Process Technol2008; 202: 328–338.
39.
Singh D and Rao PV. Improvement in surface quality with solid lubrication in hard turning. In: Proceedings of the world congress on engineering, Vol. 3, London, UK, 2–4 July 2008.
40.
QianLHossanMR. Effect on cutting force in turning hardened tool steels with cubic boron nitride inserts. J Mater Process Technol2007; 191: 274–278.
