In this work, a three-dimensional model has been proposed to predict temperature distribution and weld-pool shape during dissimilar arc welding of low-carbon steel (CK4) and ferritic stainless steel (AISI 409). The model has been developed using the finite-element software ANSYS, while in the analysis, the effects of process parameters, as well as dilution, in the weld pool have been considered. To verify the predictions, welding experiments were conducted under different welding conditions, and the model results were then compared with the measured weld-pool geometry; a reasonable consistency was observed.
PhanikumarG.ChattopadhyayK.Modeling of transport phenomena in laser welding of dissimilar metals. Int. J. Numer. Meth. Heat Fluid Flow, 2001, 11, 156–171.
4.
KatsareasD. E.YostousA. G.Residual stress prediction in dissimilar metal weld pipe joints using the finite element method. Mater. Sci. For., 2005, 490–491, 53–61.
5.
SahinS.ToparliM.OzdemirI.SasakiS.Modeled and measured residual stresses in a bimaterial joint. J. Mater. Process. Technol., 2003, 132, 235–241.
6.
ChungF. F.WeiP. S.Mass, momentum, and energy transport in a molten pool during welding dissimilar metals. J. Heat Trans., 1999, 121, 451–461.
7.
LuF.TangX.YuH.YaoS.Numerical simulation on interaction between TIG welding arc and weld pool. Comput. Mater. Sci., 2006, 35, 458–465.
8.
AcherjeeB.KuarA. S.MitraS.MisraD.Finite element simulation of laser transmission welding of dissimilar materials between polyvinylidene fluoride and titanium. Int. J. Engng, Sci. Technol., 2010, 2(4), 176–186.
9.
LeeH. T.ChenC. T.WuJ. L.Numerical and experimental investigation into effect temperature field on sensitization of Alloy 690 butt welds fabricated by gas tungsten arc welding and laser beam welding. J. Mater. Process. Technol., 2010, 21, 1636–1645.
10.
LeeC. H.ChangK. H.LeeC. Y.Comparative study of welding residual stresses in carbon andstainless steel butt welds. Proc. IMechE, PartB:J. Engineering Manufacture, 2008, 222(12), 1685–1694. DOI: 10.1243/09544054JEM124410.1243/09544054JEM1244
11.
XuJ.LiW.A finite element analysis of welding-induced distortion control for large box beam structures. Proc. IMechE, Part B: J. Engineering Manufacture, 2007, 221(2), 289–301. DOI: 10.1243/09544054JEM124410.1243/09544054JEM1244
12.
MughalM. P.MuftiR. A.FawadH.The mechanical effects of deposition patterns in welding-based layered manufacturing. Proc. IMechE, Part B: J. Engineering Manufacture, 2007, 221(B10), 1499–1509 DOI: 10.1243/09544054JEM78310.1243/09544054JEM783
13.
LuM.KouS.Power and current distribution in gas tungsten arcs. Weld. J., 1988, 67(2), 29s–33s.
14.
TaljatB.RadhakrishnanB.ZachariaT.Numerical analysis of GTA welding process with emile/hasis on post-solidification phase transformation effects on residual stresses. Mater. Sci. Engng. A, 1998, 246, 45–54.
15.
DeA.DebRoyT.A smart model to estimate effective thermal conductivity and viscosity in the weld pool. J. Appl. Phys., 2004, 95, 5230–5239.
16.
ANSYS Inc., ANSYS help system: Analysis and theory reference, ver. 8, 2004.
17.
ASM, ASM handbook. Welding, brazing and soldering, edition 9, vol. 6, p. 704 (ASM, Metals Park, Ohio).
18.
EasterlingK.Introduction to the physical metallurgy of welding, edition 2, ch. 3, 1992 (Butterworth-Heinemann Ltd, Oxford).
