The interfacial microstructure produced through tool transit of a friction stir welded lap joint between an aluminium alloy and stainless steel was studied by transmission electron microscopy in order to clarify its early stages of formation. Transmission electron microscopy studies of the bottom surface of the exit hole revealed the presence of several mixed layers of an ultrafine intermetallic compound (IMC) and stainless steel. The joining between dissimilar materials was achieved through a continuous flow of the stirred aluminium alloy into the mixed layers and the resultant growth of the ultrafine IMCs due to the heat induced by the friction between the tool and the specimen. The continuous thin reaction layer finally produced at the interface was found to be stronger than the base aluminium alloy.
MeiSW, GaoM, YanJ, ZhangC, LiG and ZengXY: ‘Interface properties and thermodynamic analysis of laser-arc hybrid welded Al/steel joint’, Sci. Technol. Weld. Join., 2013, 18, 293–300.
2.
HeH, YangC, LinS, FanC and ChenZ: ‘Flux modification for AC-TIG braze welding of aluminium to stainless steel’, Sci. Technol. Weld. Join., 2014, 19, 527–533.
3.
AgudoL, EyidiD, SchmaranzerCH, ArenholzE, JankN, BrucknerJ and PyzallaAR: ‘Intermetallic FexAly-phases in a steel/Al-alloy fusion weld’, J. Mater. Sci., 2007, 42, 4205–4214.
4.
QiuRF, IwamotoC and SatonakaS: ‘Interfacial reaction layer in resistance spot welded joint between aluminium alloy and austenitic stainless steel’, Mater. Sci. Technol., 2010, 26, 243–246.
5.
HiroseA and KobayashiK: ‘Welding and joining processes for automobiles’, J. Jpn Inst. Light Met., 2006, 56, 184–188.
6.
ThomasWM, ThreadgillPL and NicholasED: ‘Feasibility of friction stir welding steel’, Sci. Technol. Weld. Join., 1999, 4, 365–372.
7.
LeeWB, SchmueckerM, MercadoUA, BiallasG and JungSB: ‘Interfacial reaction in steel–aluminum joints made by friction stir welding’, Scr. Mater., 2006, 55, 355–358.
8.
HuseyinU, ClaudioDD, AlbertoA, TommasoG and CarlaG: ‘Friction stir welding of dissimilar Al 6013–T4 to X5CrNi18–10 stainless steel’, Mater. Des., 2005, 26, 41–46.
9.
SpringerH, KostkaA, dos SantosJF and RaabeD: ‘Influence of intermetallic phases and Kirkendall-porosity on the mechanical properties of joints between steel and aluminium alloys’, Mater. Sci. Eng. A, 2011, A528, 4630–4642.
10.
WatanabeT, YanagisawaA and TakayamaH: ‘Solid state welding aluminum alloy to steel using a rotating pin’, Q. J. Jpn Weld. Soc., 2004, 22, 141–148.
11.
MiyagawaK, TsubakiM, YasuiT and FukumotoM: ‘Spot welding between aluminum alloy and Zn coated steel by friction stirring’, Q. J. Jpn Weld. Soc., 2008, 26, 131–136.
12.
CoelhoRS, KostkaA, SheikhiS, SantosJF and PyzallaA: ‘Microstructure and mechanical properties of an AA6181-T4 aluminium alloy to HC340LA high strength steel friction stir overlap weld’, Adv. Eng. Mater., 2008, 10, 961–972.
13.
TanakaK, KumagaiM and YoshidaH: ‘Dissimilar joining of aluminum alloy and steel sheets by friction stir spot welding’, J. Jpn Inst. Light Met., 2006, 56, 317–322.
14.
KimapongK and WatanabeT: ‘Effect of welding process parameters on mechanical property of FSW lap joint between aluminum alloy and steel’, Mater. Trans., 2005, 46, 2211–2217.
15.
LeeCY, ChoiDH, YeonYM and JungSB: ‘Dissimilar friction stir spot welding of low carbon steel and Al–Mg alloy by formation of IMCs’, Sci. Technol. Weld. Join., 2009, 14, 216–220.
16.
KumaiS, SatoH, SuzukiK and OokawaT, LeeK, WatanabeM: ‘Effects of probe tip position on microstructure and bonding strength of friction stir welded aluminum alloy/steel lap joint’, J. Jpn Inst. Light Met., 2007, 57, 529–535.
17.
WatanabeM, OkawaT and KumaiS: ‘Formation of laminate structure at the friction stir weld interface of aluminum alloy/steel lap joint’, J. Jpn Inst. Light Met., 2007, 57, 536–541.
18.
OguraT, SaitoY, NishidaT, NishidaH, YoshidaT, OmichiN, FujimotoM and HiroseA: ‘Partitioning evaluation of mechanical properties and the interfacial microstructure in a friction stir welded aluminum alloy/stainless steel lap joint’, Scr. Mater., 2012, 66, 531–534.
19.
OguraT, NishidaT, TanakaY, NishidaH, YoshikawaS, FujimotoM and HiroseA: ‘Microscale evaluation of mechanical properties of a friction stir welded A6061 aluminium alloy/304 stainless steel dissimilar lap joint’, Sci. Technol. Weld. Join., 2013, 18, 108–113.
20.
ChenYC, GholiniaA and PrangnellPB: ‘Interface structure and bonding in abrasion circle friction stir spot welding: a novel approach for rapid welding aluminium alloy to steel automotive sheet’, Mater. Chem. Phys., 2012, 134, 459–463.
21.
DasH, JanaSS, PalTK and DeA: ‘Numerical and experimental investigation on friction stir lap welding of aluminium to steel’, Sci. Technol. Weld. Join., 2014, 19, 69–75.
22.
XiongJT, LiLJ, QianWJ, ZhangSF and HuangDW: ‘High strength lap joint of aluminium and stainless steels fabricated by friction stir welding with cutting pin’, Sci. Technol. Weld. Join., 2012, 17, 196–201.
23.
SchmidtHNB, DickersonTL and HattelJH: ‘Material flow in butt friction stir welds in AA2024-T3’, Acta Mater., 2006, 54, 1199–1209.
24.
PrangnellPB and HeasonCP: ‘Grain structure formation during friction stir welding observed by the “stop action technique”’, Acta Mater., 2005, 53, 3179–3192.
25.
LealRM, LeitaoC, LoureiroA, RodriguesDM and VilacaP: ‘Material flow in heterogeneous friction stir welding of thin aluminium sheets Effect of shoulder geometry’, Mater. Sci. Eng. A, 2008, A498, 384–391.
26.
TanakaT, MorishigeT and HirataT: ‘Comprehensive analysis of joint strength for dissimilar friction stir welds of mild steel to aluminum alloys’, Scr. Mater., 2009. 61, 756–759.
27.
YuH, XuZ, FanZ, ZhaoZ and LiC: ‘Mechanical property and microstructure of aluminum alloy-steel tubes joint by magnetic pulse welding’, Mater. Sci. Eng. A, 2013, A561, 259–265.
28.
KurodaS, SaidaK and NishimotoK: ‘Microstructure and properties of directly bonded joint of A6061 aluminum alloy to SUS316 stainless steel’, Q. J. Jpn Weld. Soc., 1999, 17, 484–489.
29.
GerlishA, SuP, YamamotoM and NorthTH: ‘Effect of welding parameters on the strain rate and microstructure of friction stir spot welded 2024 aluminum alloy’, J. Mater. Sci., 2007, 42, 5589–5601.
30.
SvenssonLE, KarlssonL, LarssonH, KarlssonB, FazziniM and KarlssonJ: ‘Microstructure and mechanical properties of friction stir welded aluminium alloys with special reference to AA 5083 and AA 6082’, Sci. Technol. Weld. Join., 2000, 5, 285–296.
31.
ZhangZ, ChenJT, ZhangZW and ZhangHW: ‘Coupled thermo-mechanical model based comparison of friction stir welding processes of AA2024-T3 in different thicknesses’, J. Mater. Sci., 2011, 46, 5815–5821.
32.
AvalJH, SerajzadehS and KokabiAH: ‘Evolution of microstructures and mechanical properties in similar and dissimilar friction stir welding of AA5086 and AA6061’, Mater. Sci. Eng. A, 2011, A528, 8071–8083.
