Influence of Consolidation Process on the Drilling Performance and Machinability of PIXA-M and PEEK Thermoplastic Composites

Abstract

In this paper, the drilling performance of two composite systems, namely graphite-PIXA-M (PIXA-M) and graphite-PEEK (PEEK) induction heat-pressed thermoplastic composites, are compared with their counterpart from autoclave processing. Machinability is evaluated in terms of drilling forces and hole quality. Hole quality characteristics are evaluated in terms of geometric accuracy and surface finish. The experimental observations discuss unique chip characteristics during drilling both autoclaved and induction heat-pressed thermoplastic composites. The mechanism of material removal in drilling of thermoplastic composites is investigated through the further calculation of the specific cutting energy. The induction-processed composite material produced equivalent or better holes than the autoclave-processed composites although it required larger cutting force magnitudes and protruded fibers on the bottom ply are produced. The induction heat press may be a viable alternative for the processing of thermoplastic composites in terms of drilling performance.

Keywords

drilling thermoplastic composites composite consolidation process induction heat press hole quality specific cutting energy chip formations delamination surface textures

References

Cogswell, F.N. (1992). Thermoplastic Aromatic Polymer Composites, Butterworth-Heinemann Ltd, Boston .

Mcdevitt, N. (1999). Effects of Processing Methods on the Flexural Properties of High Temperature Composite, MS Thesis, University of Washington, Seattle, WA.

Fink, Bruce K. (November 1991). Heating of Continuous-Carbon-Fiber-Reinforced Thermoplastics by Magnetic Induction, Center of Composite Materials, University of Delaware , Report No. 91-53.

Datar, Indresh P. (2000). Effect of Processing Methods on the Tensile Properties of High Temperature Composites, MS Thesis, University of Washington, Seattle, WA.

Miller, J.L. , Progar, G.J. , Johnson, W.S. and Clair, T.L.S. (April 1994). Preliminary Evaluation of Hybrid Titanium Composite Laminates, Technical Memorandum, NASA Langley Research Center .

Ramulu, M. , Stickler, P.B. , McDevitt, N.S. , Datar, I.P. , Kim, D. and Jenkins, M.G. (2004). Influence of Processing Methods on the Tensile and Flexure Properties of High Temperature Composites , Journal of Composite Science and Technology, (in press).

Di Ilio, A. , Tagliaferri, V. and Veniali, F. (1991). Damage Induced in Unidirectional Graphite Fibre Reinforced Thermoplastics during Drilling , In: Processing and Manufacturing of Composite Materials, PED-Vol. 49/MD-27, ASME.

Hocheng, H. and Puw, H.Y. (1993). Machinability of Fiber-Reinforced Thermoplastics in Drilling , Journal of Engineering Materials and Technology, 115(1): 146-149 .

Hocheng, H. and Puw, H.Y. (1992). On Drilling Characteristics of Fiber-Reinforced Thermoset and Thermoplastics , International Journal of Machine Tools Manufacturer, 32(4): 583-592 .

10.

Ramulu, M. , Branson, T. and Kim, D. (2001). A Study on the Drilling of Graphite/Bismaleimide Composite and Titanium Stacks , Composite Structures, 54(1): 67-77 .

11.

Kobayashi, Akira (1967). Machining of Plastics, McGraw-Hill, Inc., New York .

12.

Shaw, M.C. (1984). Metal Cutting Principles, Oxford University Press, New York .

13.

Veniali, F. , Di Ilio, A. and Tagliaferri (1995). An Experimental Study of the Drilling of Aramid Composites , Journal of Energy Resources Technology, 117(4): 271-278 .

14.

Wang, D.H. , Ramulu, M. and Arola, D. (1995). Orthogonal Cutting Mechanisms of Graphite/Epoxy Composite. Part I: Unidirectional Laminate , International Journal of Machine Tools and Manufacturing, 35(12): 1628-1638 .

15.

Wang, D.H. , Ramulu, M. and Arola, D. (1995). Orthogonal Cutting Mechanisms of Graphite/Epoxy Composite. Part II: Multi-directional Laminate , International Journal of Machine Tools and Manufacturing, 35(12): 1639-1648 .

16.

Colligan, K. and Ramulu, M. (1992). The Effect of Edge Trimming on Composite Surface Plies , Manufacturing Review, 5(4): 274-283 .

17.

Ho-Cheng, H. and Dharan, C.K.H. (1990). Delamination during Drilling in Composite Laminates , ASME Journal of Engineering for Industry, 112: 236-239 .

18.

Jain, S. and Yang, D.C.H. (1993). Effects of Feedrate and Chisel Edge on Delamination in Composites Drilling , Journal of Engineering for Industry, 115: 398-405 .