Compressive and energy absorption behavior of origami-inspired CF-PLA infill structures fabricated by material extrusion

Abstract

This study aims to investigate the compressive behavior and energy absorption performance of origami-inspired infill geometries fabricated using material extrusion additive manufacturing with short carbon fiber reinforced PLA (CF-PLA). The novelty of this work lies in combining art of folding paper based origami geometries (Hexagonal Kresling and Zig-Zag Origam) with CF-PLA material to achieve enhanced stiffness and specific energy absorption (SEA) compared to conventional infill patterns (line, octet, cross, and triangle). The origami and convention geimentries samples 3D printed and tested under compressive loading conditions. The Hexagonal Kresling pattern had the highest compressive strength (11.63 MPa), while the Zig-Zag Origami pattern had the best stiffness (3.48 kN/mm) and specific energy absorption (2.976 J/g). The experimental testing, a theoretical evaluation was performed using the Gibson–Ashby cellular solid model, Kelly–Tyson shear-lag theory and buckling mechanics to explain the observed stiffness enhancement and SEA behavior. Also, microstructural analysis confirmed that stress distributed evenly and that there was little layer delamination in origami-based (Zig-Zag) sample. The combination of origami-inspired design and CF-PLA enables lightweight, high-strength components with improved energy absorption and structural integrity for automotive and aerospace applications. This study provides a foundation for further geometrical optimization in additive manufacturing using origami-inspired reinforcement.

Keywords

origami structures Hexagonal kresling origami Zig-Zag origami infill pattern additive manufacturing

Get full access to this article

View all access options for this article.

References

Rouf

Malik

Singh

, et al. Additive manufacturing technologies: industrial and medical applications. Sustain Oper Comput 2022; 3: 258–274. https://doi.org/10.1016/j.susoc.2022.05.001

Lindemann

Koch

. Cost-efficient design and planning for additive manufacturing technologies. In: Proceedings of the 27th annual international solid freeform fabrication symposium – an additive manufacturing conference, 2016.

Sheoran

Kumar

. Fused deposition modeling process parameters optimization and effect on mechanical properties and part quality: review and reflection on present research. Mater Today Proc 2020; 21: 1659–1672. https://doi.org/10.1016/j.matpr.2019.11.296

Galati

Minetola

Marchiandi

, et al. A methodology for evaluating the aesthetic quality of 3D printed parts. Proced CIRP 2019; 79: 95–100. https://doi.org/10.1016/j.procir.2019.02.018

Parab

Zaveri

. Investigating the influence of infill pattern on the compressive strength of fused deposition modeled PLA parts. In: Proceedings of International Conference on Intelligent Manufacturing and Automation: ICIMA 2020. Springer, 2020, pp. 239–247. https://doi.org/10.1007/978-981-15-4485-9_25

Srinidhi

Soundararajan

Satishkumar

, et al. Enhancing the FDM infill pattern outcomes of mechanical behavior for as-built and annealed PETG and CFPETG composites parts. Mater Today Proc 2021; 45: 7208–7212. https://doi.org/10.1016/j.matpr.2021.02.417

Kovan

Tezel

Camurlu

, et al. Effect of printing parameters on mechanical properties of 3D printed PLA/carbon fibre composites. Materials Science. Non-Equilibrium Phase Transformations 2018; 4(4): 126–128.

Kamaal

Anas

Rastogi

, et al. Effect of FDM process parameters on mechanical properties of 3D-printed carbon fibre–PLA composite. Progr Addit Manuf 2021; 6: 63–69. https://doi.org/10.1007/s40964-020-00145-3

Rao

VDP

Rajiv

Navya Geethika

. Effect of fused deposition modelling (FDM) process parameters on tensile strength of carbon fibre PLA. Mater Today Proc 2019; 18: 2012–2018. https://doi.org/10.1016/j.matpr.2019.06.009

10.

Oteyaka

Aybar

Oteyaka

. Effect of infill ratio on the tensile and flexural properties of unreinforced and carbon fiber-reinforced polylactic acid manufactured by fused deposition modeling. J Mater Eng Perform 2021; 30: 5203–5215. https://doi.org/10.1007/s11665-021-05694-4

11.

Birosz

Ledenyak

Ando

. Effect of FDM infill patterns on mechanical properties. Polym Test 2022; 113: 107654. https://doi.org/10.1016/j.polymertesting.2022.107654

12.

Guduru

Gangi Setti

. 3D printed carbon fiber reinforced PLA composite using fused deposition modeling by Taguchi’s optimization: influence of printing parameters. Int J Interact Des Manuf 2024; 19: 1–11. https://doi.org/10.1007/s12008-024-02040-5

13.

Shen

Zhang

Okudan Kremer

, et al. Origami-inspired infill pattern for additive manufacturing. Manufacturing Letters 2022; 33: 516–520. https://doi.org/10.1016/j.mfglet.2022.07.066

14.

Shen

Jiang

Zhang

, et al. An origami-inspired infill pattern for additive manufacturing to reinforce the energy absorption performance. Int J Adv Manuf Technol 2022; 122(11): 4267–4274. https://doi.org/10.1007/s00170-022-09883-w

15.

Costanza

Solaiyappan

Tata

. Properties, applications and recent developments of cellular solid materials: a review. Materials 2023; 16(22): 7076. https://doi.org/10.3390/ma16227076

16.

Ashby

. The properties of foams and lattices. Philos Trans R Soc A Math Phys Eng Sci 2006; 364(1838): 15–30. https://doi.org/10.1098/rsta.2005.1678

17.

Kothandaraman

Kumar Balasubramanian

. Optimization of FDM printing parameters for square lattice structures: improving mechanical characteristics. Mater Today Proc. 2024. https://doi.org/10.1016/j.matpr.2024.04.033, In press.

18.

Bouteldja

Louar

Hemmouche

, et al. Experimental investigation of the quasi-static and dynamic compressive behavior of polymer-based 3D-printed lattice structures. Int J Impact Eng 2023; 180: 104640. https://doi.org/10.1016/j.ijimpeng.2023.104640

19.

Cooper

Kelly

. Tensile properties of fibre-reinforced metals: fracture mechanics. J Mech Phys Solid 1967; 15(4): 279–297. https://doi.org/10.1016/0022-5096(67)90017-8

20.

Piggott

. Short fibre polymer composites: a fracture-based theory of fibre reinforcement. J Compos Mater 1994; 28(7): 588–606. https://doi.org/10.1177/002199839402800701

21.

Thompson

JMT

. Basic principles in the general theory of elastic stability. J Mech Phys Solid 1963; 11(1): 13–20. https://doi.org/10.1016/0022-5096(63)90003-6

22.

Xiang

Guoxing

Zhong

. Energy absorption of origami inspired structures and materials. Thin-Walled Struct 2020; 157: 107130. https://doi.org/10.1016/j.tws.2020.107130

23.

Kelly

Tyson

. Tensile properties of fibre-reinforced metals: copper/tungsten and copper/molybdenum. J Mech Phys Solid 1965; 13(6): 329–350. https://doi.org/10.1016/0022-5096(65)90035-9

24.

Gibson

Ashby

. Cellular solids: structure and properties. Cambridge Univ, 1999. Published online.

25.

Chen

W-F

Mun Lui

. Structural stability: theory and implementation, 1987. (No Title).