In this study, the effect of different tempering time in heat treatment of thick mold steel blocks was investigated. The tempering of bainitic microstructure evolution during short (30 min) and long (14 h) tempering at 620 °C, after austenitization at 900 °C was investigated. High-resolution dilatometry and microscopy revealed that the 10% retained austenite, present before tempering, decomposes directly during tempering and indirectly into fresh martensite during cooling after short tempering. In contrast, prolonged tempering results in the complete decomposition of the retained austenite. Short tempering maintains hardness, due to the formation of fresh martensite. In prolonged tempering, hardness is significantly reduced because of the martensite–austenite constituents tempering, and recovery of low-angle grain boundaries, as confirmed by nanoindentation and electron backscatter diffraction analyses.
TalebiSHGhasemi-NanesaHJahaziM, et al.In situ study of phase transformations during non-isothermal tempering of bainitic and martensitic microstructures. Metals (Basel)2017; 7: 346.
2.
BouissaYZorganiMShahriariD, et al.Microstructure-based FEM modeling of phase transformation during quenching of large-size steel forgings. Metall Mater Trans A2021; 52: 1883–1900.
3.
BhadeshiaHKDH. Bainite in steels: transformations, microstructure and properties. 2nd ed. London: The institute of Materials, University of Cambridge, 2001.
4.
PerelomaEEdmondsDV. Phase transformations in steels. Cambridge, UK: Woodhead Publishing, 2012.
5.
ZhaoJLvBZhangF, et al.Effects of austempering temperature on bainitic microstructure and mechanical properties of a high-C high-Si steel. Mater Sci Eng A2019; 742: 179–189.
6.
BhadeshiaHWaughA. Bainite: an atom-probe study of the incomplete reaction phenomenon. Acta Metall1982; 30: 775–784.
7.
ToloueiEHurelVLoucifA, et al.Influence of the as quenched state and tempering temperature on the final microstructure and hardness of a high strength medium carbon steel. Mater Chem Phys2024; 325: 1–13.
8.
PodderAS. Tempering of a mixture of bainite and retained austenite. PhD Thesis, Department of Materials Science and Metallurgy, University of Cambridge, 2011.
9.
WuRLiJSuY, et al.Improved uniformity of hardness by continuous low temperature bainitic transformation in prehardened mold steel with large section. Mater Sci Eng A2017; 706: 15–21.
10.
Ruiz-JimenezVKuntzMSourmailT, et al.Retained austenite destabilization during tempering of low-temperature bainite. Appl Sci2020; 10: 1–20.
11.
MirzaeiSBohlooli ArkhazlooNBazdidi-TehraniF, et al.Influence of spacers and skid sizes on heat treatment of large forgings within an industrial electric furnace. Energies2023; 16: 2936.
12.
ToloueiEHurelVLoucifA, et al.Influence of the as-quenched state and tempering heating rate on microstructural characteristics of a high-strength steel. Metall Mater Trans A2025; 56: 2189–2201.
13.
WangXLiuCQinY, et al.Effect of tempering temperature on microstructure and mechanical properties of nanostructured bainitic steel. Mater Sci Eng A2022; 832: 142357.
14.
StåhlkrantzAHedströmPSariusN, et al.Effect of tempering on the bainitic microstructure evolution correlated with the hardness in a low-alloy medium-carbon steel. Metall Mater Trans A2020; 51: 6470–6481.
15.
Garcia-MateoCPeetMCaballeroFG, et al.Tempering of hard mixture of bainitic ferrite and austenite. Mater Sci Technol2004; 20: 814–818.
16.
DixitSChaudhariVKulkarniDM. Effect of tempering time on mechanical and fracture behavior of SA 387 Gr.11 pressure vessel steel. J Mater Process Technol2020; 276: 116419.
17.
BhadeshiaHKDHEdmondsDV. The bainite transformation in a silicon steel. Metall Trans A1979; 10: 895–907.
18.
LongXYZhangFCKangJ, et al.Study on carbide-bearing and carbide-free bainitic steels and their wear resistance. Mater Sci Technol2017; 33: 615–622.
19.
BrancoRBertoFZhangF, et al.Comparative study of the uniaxial cyclic behaviour of carbide-bearing and carbide-free bainitic steels. Metals (Basel)2018; 8: 422.
20.
LongXZhangFYangZ, et al.Study on microstructures and properties of carbide-free and carbide-bearing bainitic steels. Mater Sci Eng A2018; 715: 10–16.
21.
GulbayOAckermannMGramlichA, et al.Influence of transformation temperature on the high-cycle fatigue performance of carbide-bearing and carbide-free bainite. Steel Res Int2023; 94: 2300238.
22.
ANSYS Fluent Theory Guide. (2023 R2). ANSYS, Inc., Southpointe, 2600 Ansys Drive, Canonsburg, PA 15317, USA, http://www.ansys.com.
MirzaeiSArkhazlooNBMorinJ-B, et al.Influence of heating elements layout on temperature uniformity in a large size heat treatment furnace. Case Stud Therm Eng2024; 61: 105062.
BeausirBFundenbergerJ-J. In analysis tools for electron and X-ray diffraction. ATEX-software, 2017.
27.
OliverWCPharrGM. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res1992; 7: 1564–1583.
28.
YoungRA. Introduction to the Rietveld method. In: The Rietveld method. Oxford, UK: Oxford University Press, 1993, pp.1–38.
29.
AnderssonJOHelanderTHöglundL, et al.Thermodynamic databases. In Thermo-Calc and DICTRA, computational tools for materials science, ed, https://thermocalc.com/products/databases/ (2002).
30.
MoravecJDikovitsMNovakovaI, et al.Comparison of dilatometry results obtained by two different devices when generating CCT and in situ diagrams. Key Eng Mater2015; 669: 477–484.
31.
BhadeshiaHKDH. Bainite in steels: theory and practice. 3rd ed. London, UK: CRC Press, 2019.
32.
ZhengYFWuRMLiXC, et al.Continuous cooling transformation behaviour and bainite formation kinetics of new bainitic steel. Mater Sci Technol2017; 33: 454–463.
33.
ZhangZWuXCLiN, et al.Alloy optimisation of bainitic steel for large plastic mould. Mater Sci Technol2015; 31: 1706–1714.
34.
BhadeshiaH. Bainite in steels: transformation, microstructure and properties. London: The Institute of Materials, University of Cambridge, 2001, pp.98–99.
35.
CaballeroFGGarcia-MateoCde AndresCG. Dilatometric study of reaustenitisation of high silicon bainitic steels: decomposition of retained austenite. Mater Trans2005; 46: 581–586.
36.
TalebiSHJahaziMMelkonyanH. Retained austenite decomposition and carbide precipitation during isothermal tempering of a medium-carbon low-alloy bainitic steel. Materials (Basel)2018; 11: 1441.
37.
YanGHanLLiC, et al.Characteristic of retained austenite decomposition during tempering and its effect on impact toughness in SA508 Gr.3 steel. J Nucl Mater2017; 483: 167–175.
38.
FranceschiMMorales-RivasLCordova-TapiaE, et al.Study of bainite and martensite tempering in a medium C high Si steel. Microstructural disparities and equilibrium convergence. J Mater Res Technol2024; 32: 2931–2944.
39.
LerchbacherCZinnerSLeitnerH. Direct or indirect: influence of type of retained austenite decomposition during tempering on the toughness of a hot-work tool steel. Mater Sci Eng A2013; 564: 163–168.
40.
SourmailTOtterLCollinS, et al.Direct and indirect decomposition of retained austenite in continuously cooled bainitic steels: influence of vanadium. Mater Charact2021; 173: 1–10.
41.
Saha PodderABhadeshiaHKDH. Thermal stability of austenite retained in bainitic steels. Mater Sci Eng A2010; 527: 2121–2128.
42.
TamuraI. Steel material study on the strength, Vol. 40. Tokyo: Nikkan Kogyo Shinbun Ltd, 1970.
43.
HurelV. Optimazation of the heat treatment of a steel with high mechanical resistance, Mechanic, Ecole de technology superior. 2022.
44.
JiangZLiYYangZ, et al.The tempering behavior of martensite/austenite islands on the mechanical properties of a low alloy Mn-Ni-Mo steel with granular bainite. Mater Today Commun2021; 26: 102166.
45.
WangBZhangH-LXuB, et al.Sensitivity of the impact toughness and microstructure of 15CrNi3MoV steel under different quenching rates. Acta Metall Sin (Engl Lett)2023; 36: 1735–1748.
46.
LiCWHanLZLuoXM, et al.Effect of tempering temperature on the microstructure and mechanical properties of a reactor pressure vessel steel. J Nucl Mater2016; 477: 246–256.
47.
BushMEKellyPM. Strengthening mechanisms in bainitic steels. Acta Metall1971; 19: 1363–1371.
48.
KnijfDPetrovRFöjerC, et al.Effect of fresh martensite on the stability of retained austenite in quenching and partitioning steel. Mater Sci Eng A2014; 615: 107–115.
49.
BaekM-SKimK-SParkT-W, et al.Quantitative phase analysis of martensite-bainite steel using EBSD and its microstructure, tensile and high-cycle fatigue behaviors. Mater Sci Eng A2020; 785: 139375.
50.
SchneiderCARasbandWSEliceiriKW. NIH Image to ImageJ: 25 years of image analysis. Nat Methods2012; 9: 671–675.
51.
HumphreysFJHatherlyM. Chapter 4 - the structure and energy of grain boundaries. In: HumphreysFJHatherlyM (eds) Recrystallization and related annealing phenomena. 2nd ed.Oxford: Elsevier, 2004, pp.91–119.
52.
NiPShiWLuH, et al.Effect of tempering temperature on low-temperature impact toughness of 35MnB steel. J Mater Res Technol2025; 34: 2463–2476.
53.
TaneikeMSawadaKAbeF. Effect of carbon concentration on precipitation behavior of M23C6 carbides and MX carbonitrides in martensitic 9Cr steel during heat treatment. Metall Mater Trans A2004; 35: 1255–1262.
54.
DépinoySToffolon-MascletCUrvoyS, et al.Carbide precipitation in 2.25 Cr-1 Mo bainitic steel: effect of heating and isothermal tempering conditions. Metall Mater Trans A2017; 48: 2164–2178.
55.
ZhengYWangFLiC, et al.Effect of martensite structure and carbide precipitates on mechanical properties of Cr-Mo alloy steel with different cooling rate. High Temp Mater Process2019; 38: 113–124.
56.
ZhouTBabuRPHouZ, et al.Precipitation of multiple carbides in martensitic CrMoV steels - experimental analysis and exploration of alloying strategy through thermodynamic calculations. Materialia2020; 9: 100630.
57.
GorunovAI. Investigation of M7C3, M23C6 and M3C carbides synthesized on austenitic stainless steel and carbon fibers using laser metal deposition. Surf Coat Technol2020; 401: 126294.
58.
TaylorMDChoiKSSunX, et al.Correlations between nanoindentation hardness and macroscopic mechanical properties in DP980 steels. Mater Sci Eng A2014; 597: 431–439.
