Improving foamability of poly (lactic acid) (PLA) resin is a key issue for its critical foaming applications with high-performance and ultralow density. However, owing to the rheological nature of linear PLA chain structure with relatively low molecular weight, the overall foamability of PLA resin cannot meet the processing requirements of foaming purpose. Here, we describe a simple and versatile technique to prepare high foamability PLA resin by inducing chain extender through grafting octa(epoxycyclohexyl) polyhedral oligomeric silsesquioxanes (POSS) on carbon nanotubes (CNT). After the orderly assemble of the two nanoparticles, an obvious increase in melt elasticity of PLA is observed. The enhanced melt elasticity of PLA had a significant effect on controlling subsequent foaming behavior. Thus, a homogeneous and finer cellular morphology of PLA rigid foam was obtained with a proper content of CNT-POSS. Eventually, the expansion ratio of chain-extended PLA foam was 13 times higher than that of unmodified PLA foam. The proposed design methodology will potentially pave a way for designing and preparing high-performance PLA rigid foam products.
ArmentanoIBitinisNFortunatiE, et al.Multifunctional nanostructured PLA materials for packaging and tissue engineering. Prog Polym Sci2013; 38(10–11): 1720–1747.
2.
RaquezJMHabibiYMurariuM, et al.Polylactide (PLA)-based nanocomposites. Prog Polym Sci2013; 38(10-11): 1504–1542.
3.
NampoothiriKMNairNRJohnRP. An overview of the recent developments in polylactide research. Bioresour Technol2010; 101(22): 8493–8501.
4.
KotibaHMosabKMuhammadA, et al.Polylactic acid blends: the future of green, light and tough. Prog Polym Sci2018; 85(10): 83–127.
5.
GuzhovaAGalikhanovMTemnovD, et al.Improvement of polylactic acid electret properties by addition of fine barium titanate. J Electrostat2016; 79: 1–6.
6.
NofarMAmeliAParkC. A novel technology to manufacture biodegradable polylactide bead foam products. Mater Design2015; 83(15): 413–421.
7.
SaurabhCInderdeepSJungS. Recyclability analysis of PLA/sisal fiber biocomposites. Compos Part B Eng2019; 173(15): 106895.
8.
GuilongWDongmeiZGengpingW, et al.Glass fiber reinforced PLA composite with enhanced mechanical properties, thermal behavior, and foaming ability. Polymer2019; 181: 121803–121812.
9.
AoyagiYYamashitaKDoiY. Thermal degradation of poly[(r)-3-hydroxybutyrate], poly[ε-caprolactone], and poly[(s)-lactide]. Polym Degrad Stab2002; 76(1): 53–59.
10.
MikosAGThorsenAJCzerwonkaLA. Preparation and characterization of poly (L-lactic acid) foams. Polymer1994; 35: 1068–1077.
11.
ZhaiWTParkCBKontopoulouM. Nanosilica Addition dramatically improves the cell morphology and expansion ratio of polypropylene heterophasic copolymer foams blown in continuous extrusion. Ind Eng Chem Res2011; 50: 7282–7289.
12.
YanLZhenYZhenH, et al.High melt strength polypropylene by ionic modification: preparation, rheological properties and foaming behaviors. Polymer2015; 70: 207–214.
13.
CaillouxJSantanaOOFranco-UrquizaE, et al.Sheets of branched poly(lactic acid) obtained by one step reactive extrusion calendering process: melt rheology analysis. Exp Polym Lett2012; 7: 304–318.
14.
ZhouZFHuangGQXuWB, et al.Chain extension and branching of poly(L-lactic acid) produced by reaction with a DGEBA-based epoxy resin. Exp Polym Lett2007; 1: 734–739.
15.
MichalskiABrzezinskiMLapienisG, et al.Star-shaped and branched polylactides: synthesis, characterization, and properties. Prog Polym Sci2019; 89: 159–212.
16.
WangLJingXChengH, et al.Blends of linear and long-chain branched poly(l-lactide)s with high melt strength and fast crystallization rate. Ind Eng Chem Res2012; 51(30): 10088–10099.
17.
DiYWLannaceSMaiED. Reactively modified poly (lactic acid): properties and foam processing. Macromol Mater Eng2005; 290: 1083–1090.
18.
LehermeierHJDorganJR. Melt rheology of poly(lactic acid): consequences of blending chain architectures. Polym Eng Sci2001; 41: 2172–2184.
19.
WeiLMcDonaldAG. Peroxide induced cross-linking by reactive melt processing of two biopolyesters: poly(3-hydroxybutyrate) and poly(L-lactic acid) to improve their melting processability. J Appl Polym Sci2015; 132: 41724–41739.
20.
LiuJZhangSZhangL, et al.Preparation and rheological characterization of long chain branching polylactide. Polymer2014; 55: 2472–2480.
21.
LiuXYuLDeanK, et al.Improving melt strength of polylactic acid. Int Polym Process2013; 28: 64–71.
22.
WuDWuLZhangM, et al.Viscoelasticity and thermal stability of polylactide composites with various functionalized carbon nanotubes. Polym Degrad Stab2008; 93: 1577–1584.
23.
TanBHHussainHLinTT, et al.Stable dispersions of hybrid nanoparticles induced by stereocomplexation between enantiomeric poly(lactide) star polymers. Langmuir2011; 27: 10538–10547.
24.
ChenJHamonMAHuH, et al.Solution properties of single-walled carbon nanotubes. Science1998; 282: 95–98.
25.
HuHBhowmikPZhaoB, et al.Determination of the acidic sites of purified single-walled carbon nanotubes by acid–base titration. Chem Phys Lett2001; 345: 25–28.
26.
ChenYQiYTaiZ, et al.Preparation, mechanical properties and biocompatibility of graphene oxide/ultrahigh molecular weight polyethylene composites. Eur Polym J2012; 48(6): 1026–1033.
27.
AmeliAJahaniDNofarM, et al.Development of high void fraction polylactide composite foams using injection molding: mechanical and thermal insulation properties. Compos Sci Technol2014; 90(2): 88–95.
28.
YooTWYoonHGChoiSJ, et al.Effects of compatibilizers on the mechanical properties and interfacial tension of polypropylene and poly(lactic acid) blends. Macromol Res2010; 18(6): 583–588.
29.
NajafiNHeuzeyMCCarreauPJ, et al.Mechanical and morphological properties of injection molded linear and branched-polylactide (PLA) nanocomposite foams. Eur Polym J2015; 73: 455–465.
30.
BarmouzMBehraveshAH. Statistical and experimental investigation on low density microcellular foaming of PLA-TPU/cellulose nano-fiber bio-nanocomposites. Polym Test2017; 61: 300–313.
31.
NofarMTabatabaeiAAmeliA, et al.Comparison of melting and crystallization behaviors of polylactide under high-pressure CO2, N2, and He. Polymer, 2013; 54: 6471–6478.
32.
KokturkGPiskinESerhatkuluTF, et al.Evolution of phase behavior and orientation in uniaxially deformed polylactic acid films. Polym Eng Sci2002; 42: 1619–1628.
33.
LiuWHeSZhouH. Effect of octa (epoxycyclohexyl) POSS on thermal, rheology property, and foaming behavior of PLA composites. J Appl Polym Sci2018; 135: 46399–46409.
34.
OhrtCKoschineTRätzkeK, et al.Free volume in pep-silica nanocomposites with varying molecular weight. Polymer, 2014; 55: 143–149.
35.
KimESKimBCKimSH. Structural effect of linear and star-shaped poly (L-lactic acid) on physical properties. J Polym Sci B Polym Phys2004; 42: 939–946.
36.
MihaiMHuneaultMAFavisBD. Rheology and extrusion foaming of chain-branched poly (lactic acid). Polym Eng Sci2010; 50: 629–642.
37.
LiuWChenPWangXD. Effects of poly (butyleneadipate-coterephthalate) as a macromolecular nucleating agent on the crystallization and foaming behavior of biodegradable poly(lactic acid). Cell Polym2017; 36: 75–96.
38.
LiuWLiHQWangXD, et al.Effect of chain extension on the rheological property and thermal behaviour of poly(lactic acid) foams. Cell Polym2013; 6: 343–367.
39.
HingmannRMarczinkeBL. Shear and elongational flow properties of polypropylene melts. J Rheol1994; 38(3): 573–587.
40.
ChenWSunGFengG, et al.Effect of phase compatibility on the foaming behavior of LDPE/HDPE and LDPE/PP blends with subcritical CO2 as the blowing agent. J Supercrit Fluid2017; 120(2): 421–431.
41.
DeanKMPetinakisEMeureS, et al.Melt strength and rheological properties of biodegradable poly(lactic acid) modified via alkyl radical-based reactive extrusion processes. J Polym Environ2012; 20: 741–747.
42.
LudwiczakJKozlowskiM. Foaming of polylactide in the presence of chain extender. J Polym Environ2015; 23: 137–142.
43.
YuLToikkaGDeanK, et al.Foaming behaviour and cell structure of poly(lactic acid) after various modifications. Polym Int2013; 62: 759–765.
44.
BlanderMHengstenbergDKatzJL. Bubble nucleation in n-pentane, n-hexane and n-pentane hexadecane mixtures and water. J Phys Chem1971; 75(23): 3613–3619.
45.
OzgünCYilgorEYilgorI. Fabrication of rigid poly(lactic acid) foams via thermally induced phase separation. Polymer2016; 107: 240–248.
46.
Karger-KocsisJMahmoodHPegorettiA. Recent advances in fiber/matrix interphase engineering for polymer composites. Prog Mater Sci2015; 73: 1–43.
47.
SliserisJYanLKasalB. Numerical modelling of flax short fibre reinforced and flax fiber fabric reinforced polymer composites. Compos B Eng2016; 89: 143–154.
