Research and development of a composite with transparent polypropylene fiber part II: multi-quality optimization parameter design for high impact resistance of polypropylene/enhanced by rubber segment-styrene ethylene/butylene styrene composites

Abstract

The aim of this study was to present a two-step optimization system to find the optimal process parameters of the multi-quality characteristics for transparent polypropylene (PP) composites with high impact resistance enhanced by rubber segment-styrene ethylene/butylene styrene (ERS-SEBS). Three selected proportions of PP/ERS-SEBS composites were made by single-screw mixing. Injection molding was applied to fabricate the PP/ERS-SEBS composites. In the first step of the optimization, Taguchi's orthogonal array was employed to arrange the experimental work. In the second step, the back-propagation neural network (BPNN) and particle swarm optimization (PSO) were applied to find the optimum parameter settings. The BPNN established the relationship between controllable parameters and the quality responses for the fitness function, which could be established for PSO. The BPNN quality predicator was combined with PSO to present the optimal parameter settings. The qualities, impact strength, tensile strength, and haze were investigated to find the optimal process parameter settings for the best quality specification. Control factors, such as the ERS-SEBS content, melt temperature, injection speed, packing time, and influence of cooling time on the process were discussed and optimized. Finally, the effectiveness of the proposed method was evaluated by the confirmation experiments. The impact strength and tensile strength of the PP/ERS-SEBS composite were raised significantly and maintained high transparency, thereby confirming that the combination of the BPNN and PSO would constitute the best process parameter settings.

Keywords

enhanced by rubber segment-styrene ethylene/butylene styrene impact strength multi-quality optimization polypropylene tensile strength

Get full access to this article

View all access options for this article.

References

Wang

Zhang

. A novel combination of sandwich and co-continuous structure based on polypropylene and styrene-butadiene-styrene block copolymer formed with wide range of polypropylene content. J Appl Polym Sci 2018; 32: 46580.

Qazviniha

Abdouss

Musavi

et al.

Physical and mechanical properties of SEBS/polypropylene nanocomposites reinforced by nano CaCO₃. Mat.-wiss. u. werkstofftech 2016; 47: 47–52.

Karton. Performance polymers in medical applications, www.kraton.com/products/medical/documents/Medical%20Insert.pdf (2018, accessed 23 July).

Ribeiro

Simões

Pittol

et al.

Effect of copper nanoparticles on the properties of SEBS/PP compounds. Polym Test 2017; 63: 204–209.

Chen

Kurniawan

. Process parameters optimization for multiple quality characteristics in plastic injection molding using Taguchi method, BPNN, GA, and hybrid PSO-GA. Int J Precis Eng Man 2014; 15: 1583–1593.

Chen

Tai

et al.

Process parameter optimization for MIMO plastic injection molding via soft computing. Expert Syst Appl 2009; 36: 1114–1122.

Chen

Kurniawan

. A two-stage optimization system for the plastic injection molding with multiple performance characteristics. Adv Mater Res 2012; 468: 386–390.

Kuo

CFJ

Jhang

et al.

Using the Taguchi method and grey relational analysis to optimize the flat-plate collector process with multiple quality characteristics in solar energy collector manufacturing. Energy 2011; 36: 3554–3562.

Kuo

CFJ

. Optimization of multiple quality characteristics for polyether ether ketone injection molding process. Fiber Polym 2006; 7: 404–413.

10.

Kuo

CFJ

Lin

. A study of multi-quality processing parameter optimization for sueded fabric. Text Res J 2017; 87: 389–398.

11.

Kuo

C-FJ

Lan

Chen

et al.

Property modification and process parameter optimization design of polylactic acid composite materials part II: application of response surface methodology and multiobjective. Text Res J 2015; 85: 687–700.

12.

Kuo CFJ, Huang CC, Ting CH, et al. Research and development of composite with transparent polypropene fiber, part I: a Study of combining Taguchi method with analytic hierarchy process for masterbatch modification and toughening to enhance characteristics. Text Res J. 2019; 89: 389–400

13.

Lee

Kim

. Multiobjective particle swarm optimization with preference-based sort and its application to path following footstep optimization for humanoid robots. IEEE T Evolut Comput 2013; 17: 755–766.

14.

Zhu

Zhou

et al.

DNA sequence compression using adaptive particle swarm optimization-based memetic algorithm. IEEE T Evolut Comput 2011; 15: 643–658.

15.

Hsu

. Parameter optimization of sub-35 nm contact-hole fabrication using particle swarm optimization approach. Expert Syst Appl 2010; 37: 878–885.

16.

Abido

. Optimal design of power-system stabilizers using particle swarm optimization. IEEE Trans Energy Convers 2002; 17: 406–413.

17.

Material Properties of Globalene 657H. LCY Chemical Corp, Taipei City, Taiwan. https://www.lcygroup.com/lcygroup/Upload/product/product_1-201712722562114.pdf (accessed 30 May 2018).

18.

Material Properties of G1643M. Kraton Corp. A joint venture between Kraton and the Formosa Petrochemical Corporation Mailiao Township, Yunlin County, Taiwan. http://www.matweb.com/search/datasheet.aspx?matguid=1aa4d56f8541441abc1c6db427467bd0&ckck=1 (accessed 30 May 2018).

19.

Ren

Wang

et al.

Optimal parameters selection for BP neural network based on particle swarm optimization: a case study of wind speed forecasting. Knowl Based Syst 2014; 56: 226–239.

20.

Kuo

C FJ

Lee

Tsai

. Using a neural network to identify fabric defects in dynamic cloth inspection. Text Res J 2003; 73: 238–244.

21.

Baoguo

Furong

Polock

. Neural network approach to predict melt temperature in injection processes. Chin J Chem Eng 2000; 8: 326–331.

22.

Kuo

CFJ

Huang

. Computerized color separation system for printed fabrics by using backward-propagation neural network. Fiber Polym 2007; 8: 529–536.

23.

Kuo

CFJ

Hsu

CTM

Liu

et al.

Automatic inspection system of LED chip using two-stages back-propagation neural network. J Intell Manuf 2014; 25: 1235–1243.

24.

Kennedy

Eberhart

. Particle swarm optimization. Proc IEEE Int Conf Neural Netw 1995; 4: 1942–1948.

25.

Kuo

CFJ

Lan

Chen

et al.

Property modification and process parameter optimization design of polylactic acid composite materials part II: application of response surface methodology and multi-objective particle swarm optimization in the processing of polylactic acid composite fiber. Text Res J 2015; 85: 687–700.

26.

Zhang

et al.

Optimization of injection molding process parameters to improve the mechanical performance of polymer product against impact. Int J Adv Manuf Technol 2015; 76: 2199–2208.

27.

Silveira

. Development of piezoresistive fiber sensors, based on carbon black filled thermoplastic elastomer compounds, for textile application. Adv Sci Technol 2012; 80: 7–13.

28.

Lou

Huang

C L

Pan

et al.

Crystallization, mechanical and electromagnetic properties of conductive polypropylene/SEBS composite. J Polym Res 2016; 23: 84.

29.

Song

Wang

. Mechanical properties, morphology, and Mullins effect of thermoplastic elastomers based on polypropylene and waste ethylene–propylene–diene terpolymer powder compatibilized by styrene–butadiene–styrene block copolymer. J Thermoplast Compos Mater 2014; 29: 410–424.

30.

Yang

Huang

et al.

Influences of dicumyl peroxide on morphology and mechanical properties of polypropylene/poly(styrene-b-butadiene-b-styrene) blends via vane-extruder. J Appl Polym Sci 2015; 132: 41543.

31.

Rapa

Ghioca

Matei

et al.

Influence of chitosan on mechanical, thermal, barrier and antimicrobial properties of PLA-biocomposites for food packaging. Mater Plast 2016; 102: 112–121.