This paper presents an experimental study and modeling of the influence of surface density and fiber length on the permeability of novel nonwoven flax fiber manufactured by the paper making process. Firstly, the relation between surface density, fiber lengths and pore size distribution measured with a porometer capillary instrument is reported in this study. The results show that higher surface density gives a denser fibrous network with a low porosity rate and longer fiber decreases the total number of fibers and increases the pore size for a given surface density. A liquid permeability study was then carried out to identify the impact of surface density, short fiber length and fiber volume fraction on in-plane impregnation of the reinforcement. Permeability was found to be inversely proportional to the reinforcement of surface density. In contrast, an increase of the fiber length increases the in-plane permeability of the reinforcement. Finally, a mathematical modeling is proposed to predict the permeability behavior of these innovative natural fiber webs.
LekakouCJohariMNormanDet al.Measurement techniques and effects on in-plane permeability of woven cloths in resin transfer moulding. Composites Part A1996; 27A: 401–408.
2.
Gebart B. Permeability of unidirectional reinforcements for RTM. J Compos Mater 1992; 26: 1100–1133.
3.
GerdMMassimoBSvenBet al.A reference specimen for permeability measurements of fibrous reinforcements for RTM. Composites2009; 40: 244–250.
4.
Ledru Y. Etude de la porosité dans les materiaux composites stratifies aeronautiques. PhD Thesis, Institut National Polytechnique de Toulouse, France, 2009, p.22.
5.
BaichenLBickertonSAdvaniS. Modelling and simulation of resin transfer molding (RTM) – Gate control, venting and dry spot prediction. Composites1996; 27A: 135–141.
6.
Qiang L, Richard SP and Hermione SG. New set-up for in-plane permeability measurement. Composites Part A 2007; 38: 954–962.
7.
KrisHDanielaDHugoSet al.New set-up for measurement of permeability properties of fibrous reinforcements for RTM. Composites Part A2002; 33: 959–969.
8.
WeitzenbockJRShenoiRAWilsonPA. Radial flow permeability measurement. Part A: Theory. Composites Part A1999; 30: 781–796.
9.
KruckenbergTPatonR. Resin transfer moulding for aerospace structures, Dordrecht: Kluwer Academic Publishers, 1998.
10.
GebartRLinstromP. Measurement of in-plane permeability of anisotropic fiber reinforcements. Polym Compos1996; 17: 43–51.
11.
SchmidtTGossTAmicoSet al.Permeability of hybrid reinforcements and mechanical properties of their composites molded by resin transfer molding. J Reinf Plast Compos2009; 28: 2839–2850.
12.
UmerRBickertonSFernyhoughA. The effect of yarn length and diameter on permeability and compaction response of flax fibre mats. Composites Part A2011; 42: 723–732.
13.
FrancucciGVázquezARuizEet al.Capillary effects in vacuum-assisted resin transfer molding with natural fibers. Polym Compos2012; 33: 1593–1602.
14.
KuHWangHPattarachaiyakoopNet al.A review on the tensile properties of natural fiber reinforced polymer composites. Composites Part B2011; 42: 856–873.
15.
SliserisJYanLKasalB. Numerical modelling of flax short fibre reinforced and flax fibre fabric reinforced polymer composites. Composites Part B2016; 89: 143–154.
16.
YanLSuSChouwN. Microstructure, flexural properties and durability of coir fibre reinforced concrete beams externally strengthened with flax FRP composites. Composites Part B2015; 80: 343–354.
17.
DittenberDBGangaRaoHV. Critical review of recent publications on use of natural composites in infrastructure. Composites Part A2012; 43: 1419–1429.
18.
KoronisGSilvaAFontulM. Green composites: a review of adequate materials for automotive applications. Composites Part B2013; 44: 120–127.
19.
YanLChouwNJayaramanK. Flax fibre and its composites – a review. Composites Part B2014; 56: 296–317.
20.
La MantiaFPMorrealeM. Green composites: a brief review. Composites Part A2011; 42: 579–588.
21.
DickerMPMDuckworthPFBakerABet al.Green composites: a review of material attributes and complementary applications. Composites Part A2014; 56: 280–289.
22.
ShahDUSchubelPJCliffordMJ. Can flax replace E-glass in structural composites? A small wind turbine blade case study. Composites Part B2013; 52: 172–181.
23.
PilLBensadounFParisetJet al.Why are designers fascinated by flax and hemp fibre composites?Composites Part A2016; 83: 193–205.
24.
LiuQHughesM. The fracture behaviour and toughness of woven flax fibre reinforced epoxy composites. Composites Part A2008; 39: 1644–1652.
25.
LiangSGningP-BGuillaumatL. Properties evolution of flax/epoxy composites under fatigue loading. Int J Fatigue2014; 63: 36–45.
26.
Le DuigouAKervoelenALe GrandAet al.Interfacial properties of flax fibre–epoxy resin systems: existence of a complex interphase. Compos Sci Technol2014; 100: 152–157.
27.
LiangSGningPBGuillaumatL. A comparative study of fatigue behaviour of flax/epoxy and glass/epoxy composites. Compos Sci Technol2012; 72: 535–543.
28.
Cuinat-GuerrazNDumontM-JHubertP. Environmental resistance of flax/bio-based epoxy and flax/polyurethane composites manufactured by resin transfer moulding. Composites Part A2016; 88: 140–147.
29.
OksmanK. High quality flax fibre composites manufactured by the resin transfer moulding process. J Reinf Plast Compos2001; 20: 621–627.
30.
Van de WeyenbergIIvensJDe CosterAet al.Influence of processing and chemical treatment of flax fibres on their composites. Compos Sci Technol2003; 63: 1241–1246.
31.
HughesMCarpenterJHillC. Deformation and fracture behaviour of flax fibre reinforced thermosetting polymer matrix composites. J Mater Sci2007; 42: 2499–2511.
32.
Phillips S, Baets J, Lessard L, et al. Characterization of flax/epoxy prepregs before and after cure. J Reinf Plast Compos 2013; 32: 777–785.
33.
MittalVSainiRSinhaS. Natural fiber-mediated epoxy composites – a review. Composites Part B2016; 99: 425–435.
34.
Pomeroy RAH. Permeability characterisation of continuous filament mats for resin transfer moulding. PHD Thesis, University of Plymouth, Royaume-Uni, 2009, pp.60–70.
35.
LeBel F, Fanaei AE, Ruiz E, et al. Experimental characterization by fluorescence of capillary flows in dual-scale engineering fabrics. Text Res J 2013; 83: 1634–1659.
36.
RaveyCRuizETrochuF. Determination of the optimal impregnation velocity in Resin Transfer Molding by capillary rise experiments and infrared thermography. Compos Sci Technol2014; 99: 96–102.
37.
LeBelFFanaeiAERuizEet al.Prediction of optimal flow front velocity to minimize void formation in dual scale fibrous reinforcements. Int J Mater Form2014; 7: 93–116.
38.
CuperusFPSmoldersCA. Characterization of UF membranes: membrane characteristics and characterization techniques. Adv Colloid Interface Sci1991; 34: 135–173.
Q. Instruments. POROMETER 3G SERIES through-pore size analyzer, 2015.
41.
VernetNet al.Experimental determination of the permeability of engineering textiles: benchmark II. Composites Part A2014; 61: 172–184.
42.
Masoodi R, Pillai KM and Verhagen MA. Flow modeling in natural-fiber preforms used in liquid composite molding. In: Proceedings of the 1st joint American-Canadian international conference on composites, Newark, Delaware, USA, 15–17 September 2009.
43.
Francucci GM, Rodriguez ES and Vázquez. A study of the compaction behavior of natural fiber reinforcements in liquid composite molding processes. In: The 10th International Conference on Flow Processes in Composite Materials (FPCM10), Monte Verita, Ascona (Ticiono) – Switzerland, 12–15 July 2010.
44.
FrancucciGRodríguezESVázquezA. Study of saturated and unsaturated permeability in natural fiber fabrics. Composites Part A2010; 41: 16–21.
45.
PillaiKAdvaniS. A model for unsaturated flow in woven fiber preforms during mold filling in resin transfer molding. J Compos Mater1998; 32: 1753–1783.
46.
Siddiqur RahmanMMatinNMajidMet al.Swelling characteristics of jute fibre with water and different organic and inorganic vapours and liquids. Cellulose Chem Technol1997; 31: 87–92.
47.
Vázquez A, Ruiz E, Francucci G, et al. Key factors affecting processing of natural fiber composites. Plastics Research Online, 20 December 2012.
48.
LimpertEStahelWAAbbtM. Log-normal distributions across the sciences: keys and clues: on the charms of statistics, and how mechanical models resembling gambling machines offer a link to a handy way to characterize log-normal distributions, which can provide deeper insight into variability and probability—normal or log-normal: that is the question. BioScience2001; 51: 341–352.
49.
UmerRBickertonSFernyhoughA. Characterising wood fibre mats as reinforcements for liquid composite moulding processes. Composites Part A2007; 38: 434–448.
50.
FrancucciGVázquezARodríguezES. Key differences on the compaction response of natural and glass fiber preforms in liquid composite molding. Text Res J2012; 82: 1774–1785.
