The beneficial effect of STF impregnation in enhancing the impact resistance of high-performance fabrics has been extensively reported in the literature. However, this research work reports that fabric structure has a decisive role in moderating the effectiveness of STF impregnation in terms of impact energy absorption. Plain woven fabrics having sett varying from 25 × 25 inch−1 to 55 × 55 inch−1 were impregnated with STF at two different padding pressures to obtain different add-ons. The impact energy absorption by STF impregnated loosely woven fabrics was found to be higher than that of their neat counterparts for both levels of add-on, while opposite trend was observed in case of tightly woven fabrics. Further, comparison of tightly woven plain, 2/2 twill, 3/1 twill and 2 × 2 matt fabrics revealed beneficial effect of STF impregnation, except for the plain woven fabric, establishing that there exists a fabric structure-STF impregnation interplay that tunes the impact resistance of woven fabrics.
MawkhliengUMajumdarALahaA.
A review of fibrous materials for soft body armour applications. RSC Adv2020;
10: 1066–1086.
2.
Zhou Y. Development of lightweight soft body armour for ballistic protection. PhD thesis. University of Manchester, 2013.
3.
ParkJLChiY-SKangTJ.
Ballistic performance of hybrid panels composed of unidirectional/woven fabrics. Text Res J2013;
83: 471–486.
4.
KarahanM.
Comparison of ballistic performance and energy absorption capabilities of woven and unidirectional aramid fabrics. Text Res J2008;
78: 718–730.
5.
OthmanARHassanMH.
Effect of different construction designs of aramid fabric on the ballistic performances. Mater Des2013;
44: 407–413.
6.
MajumdarALahaABhattacharjeeD, et al.
Tuning the structure of 3D woven aramid fabrics reinforced with shear thickening fluid for developing soft body armour. Compos Struct2017;
178: 415–425.
7.
AbtewMABoussuFBruniauxP, et al.
Engineering of 3D warp interlock p-aramid fabric structure and its energy absorption capabilities against ballistic impact for body armour applications. Compos Struct2019;
225: 111179.
8.
YangDChenX.
Multi-layer pattern creation for seamless front female body armor panel using angle-interlock woven fabrics. Text Res J2017;
87: 381–386.
9.
Wagner N and Wetzel ED. Conformable ballistic resistant and protective composite materials composed of shear thickening fluids reinforced by short fibers. US20090004413A1, US.
10.
MajumdarAButolaBSSrivastavaA, et al.
Improving the impact resistance of p-aramid fabrics by sequential impregnation with shear thickening fluid. Fibers Polym2016;
17: 199–204.
11.
HassanTARangariVKJeelaniS.
Synthesis, processing and characterization of shear thickening fluid (STF) impregnated fabric composites. Mater Sci Eng A2010;
527: 2892–2899.
12.
HasanzadehMMottaghitalabV.
The Role of Shear-Thickening Fluids (STFs) in Ballistic and Stab-Resistance Improvement of Flexible Armor. J of Materi Eng and Perform2014;
23: 1182–1196.
13.
SunDZhuFStyliosGK.
Investigation of composite fabric impregnated with non-Newtonian fluid for protective textiles. J Compos Mater2020;
54: 1013–1021.
14.
SunDChenX.
Plasma modification of Kevlar fabrics for ballistic applications. Text Res J2012;
82: 1928–1934.
15.
FirouziDChingCYRizviSN, et al.
Development of oxygen-plasma-surface-treated UHMWPE fabric coated with a mixture of SiC/polyurethane for protection against puncture and needle threats. Fibers2019;
7: 46.
16.
MajumdarASingh ButolaBAwasthiN, et al.
Improving the mechanical properties of p-aramid fabrics and composites by developing ZnO nanostructures. Polym Compos2018;
39: 3300–3306.
17.
HazarikaADekaBKKimDY, et al.
Growth of aligned ZnO nanorods on woven Kevlar® fiber and its performance in woven Kevlar® fiber/polyester composites. Compos Part A Appl Sci Manuf2015;
78: 284–293.
18.
BenzaitZTrabzonL.
A review of recent research on materials used in polymer–matrix composites for body armor application. J Compos Mater2018;
52: 3241–3263.
19.
AhmadMRAhmadWYWSamsuriA, et al.
Ballistic response of natural rubber latex coated and uncoated fabric systems. J Rubber Res2007;
10: 207–221.
20.
RoyRMajumdarAButolaBS.
Comparative Study of P-aramid Based Soft and Stiff Composite Panels for Protective Application. Fibers Polym2019;
20: 406–412.
21.
Park S-J and Seo M-K. Element and processing. In: Interface Science and Technology. Elsevier, 2011. pp. 431–499.
22.
CrouchIG.
Body armour – New materials, new systems. Def Technol2019;
15: 241–253.
23.
BajyaMMajumdarAButolaBS, et al.
Design strategy for optimising weight and ballistic performance of soft body armour reinforced with shear thickening fluid. Compos Part B Eng2020;
183: 107721.
24.
KędzierskiPGieletaRMorkaA, et al.
Experimental study of hybrid soft ballistic structures. Compos Struct2016;
153: 204–211.
25.
ĆwikTKIannucciLCurtisP, et al.
Design and Ballistic Performance of Hybrid Composite Laminates. Appl Compos Mater2017;
24: 717–733.
26.
AroraSLahaAMajumdarA, et al.
Prediction of rheology of shear thickening fluids using phenomenological and artificial neural network models. Korea-Aust Rheol J2017;
29: 185–193.
MajumdarAButolaBSSrivastavaA.
An analysis of deformation and energy absorption modes of shear thickening fluid treated Kevlar fabrics as soft body armour materials. Mater Des2013;
51: 148–153.
29.
HeQCaoSWangY, et al.
Impact resistance of shear thickening fluid/Kevlar composite treated with shear-stiffening gel. Compos Part A Appl Sci Manuf2018;
106: 82–90.
30.
MajumdarALahaABhattacharjeeD, et al.
Soft body armour development by silica particle based shear thickening fluid coated p -aramid fabrics. J Text Inst2019;
110: 1515–1518.
31.
LeeYSWetzelEDWagnerNJ.
The ballistic impact characteristics of Kevlar® woven fabrics impregnated with a colloidal shear thickening fluid. J Mater Sci2003;
38: 2825–2833.
32.
KangTJHongKHYooMR.
Preparation and properties of fumed silica/Kevlar composite fabrics for application of stab resistant material. Fibers Polym2010;
11: 719–724.
33.
MawkhliengUMajumdarA.
Deconstructing the role of shear thickening fluid in enhancing the impact resistance of high-performance fabrics. Compos Part B Eng2019;
175: 107167.
34.
GürgenS.
An investigation on composite laminates including shear thickening fluid under stab condition. J Compos Mater2019;
53: 1111–1122.
35.
AlikaramiSKordaniNSadoughVaniniA, et al.
Effect of the yarn pull-out velocity of shear thickening fluid-impregnated Kevlar fabric on the coefficient of friction. J Mech Sci Technol2016;
30: 3559–3565.
36.
AroraSMajumdarAButolaBS.
Soft Armour Design by Angular Stacking of Shear Thickening Fluid Impregnated High-Performance Fabrics for Quasi-Isotropic Ballistic Response. Compos Struct2020;
233: 111720.
37.
LiWXiongDZhaoX, et al.
Dynamic stab resistance of ultra-high molecular weight polyethylene fabric impregnated with shear thickening fluid. Mater Des2016;
102: 162–167.
38.
QinJZhangGZhouL, et al.
Dynamic/quasi-static stab-resistance and mechanical properties of soft body armour composites constructed from Kevlar fabrics and shear thickening fluids. RSC Adv2017;
7: 39803–39813.
39.
ParkJLYoonBIPaikJG, et al.
Ballistic performance of p-aramid fabrics impregnated with shear thickening fluid; Part I – Effect of laminating sequence. Text Res J2012;
82: 527–541.
40.
KhodadadiALiaghatGSabetA, et al.
Experimental and numerical analysis of penetration into Kevlar fabric impregnated with shear thickening fluid. J Thermoplast Compos Mater2018;
31: 392–407.
41.
LarssonFSvenssonL.
Carbon, polyethylene and PBO hybrid fibre composites for structural lightweight armour. Compos Part A Appl Sci Manuf2002;
33: 221–231.
42.
KarbalaieMYazdaniradMMirhabibiA.
High performance Dyneema® fiber laminate for impact resistance/macro structural composites. J Thermoplast Compos Mater2012;
25: 403–414.
43.
SunL-LXiongD-SXuC-Y.
Application of shear thickening fluid in ultra high molecular weight polyethylene fabric. J Appl Polym Sci2013;
129: 1922–1928.
44.
GuJHuangXLiY, et al.
Improving the stab-resistance performance of ultra high molecular weight polyethylene fabric intercalated with nano-silica-fluid. J Shanghai Jiaotong Univ (Sci)2014;
19: 102–109.
45.
ZengXSTanVBCShimV.
Modelling inter-yarn friction in woven fabric armour. Int J Numer Meth Engng2006;
66: 1309–1330.
46.
DasSJaganSShawA, et al.
Determination of inter-yarn friction and its effect on ballistic response of para-aramid woven fabric under low velocity impact. Compos Struct2015;
120: 129–140.
47.
AroraSMajumdarAButolaBS.
Structure induced effectiveness of shear thickening fluid for modulating impact resistance of UHMWPE. Compos Struct2019;
210: 41–48.
48.
GürgenSKuşhanMC.
The ballistic performance of aramid based fabrics impregnated with multi-phase shear thickening fluids. Polym Test2017;
64: 296–306.
49.
WagnerNJBradyJF.
Shear thickening in colloidal dispersions. Phys Today2009;
62: 27–32.
50.
GürgenSLiWKuşhanMC.
The rheology of shear thickening fluids with various ceramic particle additives. Mater Des2016;
104: 312–319.
51.
GürgenS.
Tuning the Rheology of Nano-Sized Silica Suspensions with Silicon Nitride Particles. JNanoR2019;
56: 63–70.
52.
GürgenSKuşhanMCLiW.
The effect of carbide particle additives on rheology of shear thickening fluids. Korea-Aust Rheol J2016;
28: 121–128.
53.
GürgenSKuşhanMCLiW.
Shear thickening fluids in protective applications: A review. Prog Polym Sci2017;
75: 48–72.
54.
LahaAMajumdarA.
Interactive effects of p-aramid fabric structure and shear thickening fluid on impact resistance performance of soft armor materials. Mater Des2016;
89: 286–293.
