In situ characterization of direction-dependent cure-induced shrinkage in thermoset composite laminates with fiber-optic sensors embedded in through-thickness and in-plane directions
Restricted accessResearch articleFirst published online April, 2015
In situ characterization of direction-dependent cure-induced shrinkage in thermoset composite laminates with fiber-optic sensors embedded in through-thickness and in-plane directions
This study develops a fiber-optic-based technique for in situ characterization of direction-dependent cure-induced shrinkage in thermoset fiber-reinforced composites. A procedure is established to embed fiber Bragg grating (FBG) sensors in composite out-of-plane directions and to measure key through-thickness chemical cure shrinkage directly under practical curing conditions. First, sensitivity of the proposed method is evaluated through comparison with a standard technique (i.e. thermo-mechanical analysis (TMA)), and the effect of sensor tail length on measurement sensitivity is discussed considering shear-lag effect. Next, combined with double-sided vacuum bagging and demolding during curing, FBG sensors embedded in through-thickness and in-plane directions clarify direction-dependent cure-induced shrinkage in autoclaved unidirectional carbon/epoxy. Finally, the feasibility of characterizing through-thickness shear strain, which is important in complex-shaped parts but cannot be measured using conventional techniques, is confirmed. The developed technique will be a powerful tool for evaluating cure shrinkage in complex-shaped parts and for validating process-simulation tools based on internal strain.
WisnomMRGigliottiMErsoyN. Mechanisms generating residual stresses and distortion during manufacture of polymer–matrix composite structures. Compos Part A: Appl Sci Manuf2006; 37: 522–529.
2.
JohnstonAVaziriRPoursartipA. A plane strain model for process-induced deformation of laminated composite structures. J Compos Mater2001; 35: 1435–1469.
3.
SvanbergJMHolmbergJA. An experimental investigation on mechanisms for manufacturing induced shape distortions in homogeneous and balanced laminates. Compos Part A: Appl Sci Manuf2001; 32: 827–838.
4.
Nawab Y, Shahid S, Boyard N, et al. Chemical shrinkage characterization techniques for thermoset resins and associated composites. J Mater Sci 2013; 48(16): 5387–5409.
5.
LuyckxGVoetELammensN. Strain measurements of composite laminates with embedded fibre Bragg gratings: criticism and opportunities for research. Sensors2011; 11: 384–408.
6.
ParlevlietPPBerseeHENBeukersA. Residual stresses in thermoplastic composites—A study of the literature—Part II: Experimental techniques. Compos Part A: Appl Sci Manuf2007; 38: 651–665.
7.
ColpoFHumbertLBotsisJ. Characterisation of residual stresses in a single fibre composite with FBG sensor. Compos Sci Technol2007; 67: 1830–1841.
8.
ColpoFHumbertLGiaccariP. Characterization of residual strains in an epoxy block using an embedded FBG sensor and the OLCR technique. Compos Part A: Appl Sci Manuf2006; 37: 652–661.
9.
AntonucciVCusanoAGiordanoM. Cure-induced residual strain build-up in a thermoset resin. Compos Part A: Appl Sci Manuf2006; 37: 592–601.
10.
GiordanoMLaudatiANasserJ. Monitoring by a single fiber Bragg grating of the process induced chemo-physical transformations of a model thermoset. Sens Actuators A Phys2004; 113: 166–173.
11.
LammensNKinetDChahK. Residual strain monitoring of out-of-autoclave cured parts by use of polarization dependent loss measurements in embedded optical fiber Bragg gratings. Compos Part A: Appl Sci Manuf2013; 52: 38–44.
12.
MinakuchiSUmeharaTTakagakiK. Life cycle monitoring and advanced quality assurance of L-shaped composite corner part using embedded fiber-optic sensor. Compos Part A: Appl Sci Manuf2013; 48: 153–161.
13.
Takagaki K, Minakuchi S and Takeda N. Fiber-optic-based life cycle monitoring of through-thickness strain in thick CFRP pipes. Adv Compos Mater 2014; 23(3): 195–209.
14.
Nielsen MW, Schmidt JW, Hattel JH, et al. In situ measurement using FBGs of process-induced strains during curing of thick glass/epoxy laminate plate: experimental results and numerical modeling. Wind Energy 2013; 16(8): 1241–1257.
15.
MinakuchiSTakedaNTakedaS. Life cycle monitoring of large-scale CFRP VARTM structure by fiber-optic-based distributed sensing. Compos Part A: Appl Sci Manuf2011; 42: 669–676.
16.
KhounLde OliveiraRMichaudV. Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites. Compos Part A: Appl Sci Manuf2011; 42: 274–282.
17.
MulleMCollombetFOlivierP. Assessment of cure-residual strains through the thickness of carbon–epoxy laminates using FBGs Part II: Technological specimen. Compos Part A: Appl Sci Manuf2009; 40: 1534–1544.
18.
MulleMCollombetFOlivierP. Assessment of cure residual strains through the thickness of carbon–epoxy laminates using FBGs, Part I: Elementary specimen. Compos Part A: Appl Sci Manuf2009; 40: 94–104.
19.
Hernández-MorenoHCollombetFDouchinB. Entire life time monitoring of filament wound composite cylinders using Bragg grating sensors: II. Process monitoring. Appl Compos Mater2009; 16: 197–209.
20.
de OliveiraRLavanchySChattonR. Experimental investigation of the effect of the mould thermal expansion on the development of internal stresses during carbon fibre composite processing. Compos Part A: Appl Sci Manuf2008; 39: 1083–1090.
21.
MontaniniRD'AcquistoL. Simultaneous measurement of temperature and strain in glass fiber/epoxy composites by embedded fiber optic sensors: I. Cure monitoring. Smart Mater Struct2007; 16: 1718–1726.
22.
EumSHKageyamaKMurayamaH. Structural health monitoring using fiber optic distributed sensors for vacuum‐assisted resin transfer molding. Smart Mater Struct2007; 16: 2627–2635.
23.
JungKKangTJ. Cure monitoring and internal strain measurement of 3-D hybrid braided composites using fiber Bragg grating sensor. J Compos Mater2007; 41: 1499–1519.
24.
ChehuraESkordosAAYeC-C. Strain development in curing epoxy resin and glass fibre/epoxy composites monitored by fibre Bragg grating sensors in birefringent optical fibre. Smart Mater Struct2005; 14: 354–362.
25.
JinnoMSakaiSOsakaK. Smart autoclave processing of thermoset resin matrix composites based on temperature and internal strain monitoring. Adv Compos Mater2003; 12: 57–72.
26.
KangH-KKangD-HHongC-S. Simultaneous monitoring of strain and temperature during and after cure of unsymmetric composite laminate using fibre-optic sensors. Smart Mater Struct2003; 12: 29–35.
27.
KangH-KKangD-HBangH-J. Cure monitoring of composite laminates using fiber optic sensors. Smart Mater Struct2002; 11: 279–287.
28.
BaoXHuangCZengX. Simultaneous strain and temperature monitoring of the composite cure with a Brillouin-scattering-based distributed sensor. Optic Eng2002; 41: 1496–1501.
29.
LengJSAsundiA. Real-time cure monitoring of smart composite materials using extrinsic Fabry-Perot interferometer and fiber Bragg grating sensors. Smart Mater Struct2002; 11: 249–255.
30.
KimYKDanielIM. Cure cycle effect on composite structures manufactured by resin transfer molding. J Compos Mater2002; 36: 1725–1743.
31.
MurukeshanVMChanPYOngLS. Cure monitoring of smart composites using Fiber Bragg Grating based embedded sensors. Sens Actuators A Phys2000; 79: 153–161.
32.
KalamkarovALFitzgeraldSBMacDonaldDO. The use of Fabry Perot fiber optic sensors to monitor residual strains during pultrusion of FRP composites. Compos Part B: Eng1999; 30: 167–175.
33.
Dewynter-MartyVFerdinandPBocherensE. Embedded fiber Bragg grating sensors for industrial composite cure monitoring. J Intell Mater Syst Struct1998; 9: 785–787.
34.
O'DwyerMJMaistrosGMJamesSW. Relating the state of cure to the real-time internal strain development in a curing composite using in-fibre Bragg gratings and dielectric sensors. Measure Sci Technol1998; 9: 1153–1158.
35.
LawrenceCMNelsonDVBennettTE. An embedded fiber optic sensor method for determining residual stresses in fiber-reinforced composite materials. J Intell Mater Syst Struct1998; 9: 788–799.
36.
LawrenceCMNelsonDVBennettTE. Measurement of process-induced strains in composite materials using embedded fiber optic sensors. SPIE1996; 2718: 60–68.
37.
OthonosAKalliK. Fiber Bragg gratings: fundamentals and applications in telecommunications and sensing, Norwood, MA: Artech House Publishers, 1999.
38.
ZhouGSimLMBrewsterPA. Through-the-thickness mechanical properties of smart quasi-isotropic carbon/epoxy laminates. Compos Part A: Appl Sci Manuf2004; 35: 797–815.
39.
SatoriKIkedaYKurosawaY. Development of small-diameter optical fiber sensors for damage detection in composite laminates. SPIE2000; 3986: 104–111.
40.
HullDClyneTW. An introduction to composite materials. Chapter 6, Stresses and strains in short-fibre composites, Cambridge, MA: Cambridge University Press, 1996.
41.
ErsoyNGarstkaTPotterK. Modelling of the spring-in phenomenon in curved parts made of a thermosetting composite. Compos Part A: Appl Sci Manuf2010; 41: 410–418.
GafsiREl-SherifMA. Analysis of induced-birefringence effects on fiber Bragg gratings. Optic Fiber Technol2000; 6: 299–323.
44.
SvanbergJMHolmbergJA. Prediction of shape distortions Part I. FE-implementation of a path dependent constitutive model. Compos Part A: Appl Sci Manuf2004; 35: 711–721.
45.
KominarV. Thermo-mechanical regulation of residual stresses in polymers and polymer composites. J Compos Mater1996; 30: 406–415.
46.
GarstkaTErsoyNPotterKD. In situ measurements of through-the-thickness strains during processing of AS4/8552 composite. Compos Part A: Appl Sci Manuf2007; 38: 2517–2526.
47.
WisnomMPotterKErsoyN. Shear-lag analysis of the effect of thickness on spring-in of curved composites. J Compos Mater2007; 41: 1311–1324.
