Thrust Force and Wear Assessment When Drilling Glass Fiber-Reinforced Polymeric Composite

Abstract

The principal aim of this article is to investigate the influence of the drilling parameters and tool material/coating (high speed steel and plain and coated carbide) on the thrust force and tool wear when drilling glass fiber reinforced epoxy composite. In order to predict the performance of the cutting tools in the industrial environment, extended drilling tests (up to 24000 holes) were conducted and the influence of changes in the geometry of the drills on the thrust force was assessed. The results indicated that the high speed steel tool presented remarkable wear rates, which drastically altered its edge preparation and resulted in a thrust force of 492 N after 1000 holes. In opposition to that, the cemented carbide drill presented superior wear resistance, with a thrust force of 147N after drilling 24000 holes. Finally, the use of the titanium nitride coated drill did not offer a significant contribution neither to the tool wear resistance nor to the machining thrust force.

Keywords

drilling composite thrust force tool wear.

Get full access to this article

View all access options for this article.

References

Adams, R.D. and Maheri, M.R. (2003). Damping in Advanced Polymer-Matrix Composites , Journal of Alloys and Compounds, 355: 126-130.

Buggy, M. , Farragher, L. and Madden,W. ( 1995). Recycling of Composite Materials, Journal of Materials Processing Technology, 55: 448-456.

Stone, R. and Krishnamurthy, K. (1996). A Neural Network Thrust Force Controller to Minimize Delamination during Drilling of Graphite Epoxy Laminates, International Journal of Machine Tools and Manufacture , 36(9): 985-1003.

Sreejith, P.S. , Krishnamurthy, R. , Malhotra, S.K. and Narayanasamy , K. (1999). Studies on the Machining of Carbon: Phenolic Ablative Composites, Journal of Materials Processing Technology, 88: 43-50.

Rahman, M. , Ramakrishna, S. , Prakash, J.R.S. and Tan, D.C.G. (1999). Machinability Study of Carbon Fiber Reinforce Composite, Journal of Materials Processing Technology, 89: 292-297.

Ferreira, J.R. , Coppini, N.L. and Levy Neto , F. (2001). Characteristics of carbon-carbon composite turning, Journal of Materials Processing Technology, 109: 65-71.

Wang, D.H. , Ramulu, M. and Arola, D. (1995). Orthogonal Cutting Mechanisms of Graphite/ Epoxy Composite, Part I: Unidirectional Laminate, International Journal of Machine Tools and Manufacture, 35(12): 1623-1638.

Velayudham, A. , Krishnamurthy, R. and Soundarapandian , T. (2005). Evaluation of Drilling Characteristics of High Volume Fraction Fibre Glass Reinforced Polymeric Composite, International Journal of Machine Tools and Manufacture, 45: 399-406.

Dharan, C.K.H. and Won, M.S. (2000). Machining Parameters for an Intelligent Machining System for Composite Laminates, International Journal of Machine Tools and Manufacture, 40: 415-426.

10.

Abrão, A.M. , Faria, P.E. , Campos Rubio , J.C. , Reis, P. and Davim, J.P. (2007). Drilling of Fiber Reinforced Plastics: A Review, Journal of Materials Processing Technology, 186: 1-7.

11.

Mathew, J. , Ramakrishnan, N. and Naik, N.K. (1999). Investigations into the Effect of Geometry of a Trepanning Tool on Thrust and Torque During Drilling of GFRP Composites , Journal of Materials Processing Technology, 91(1): 1-11.

12.

Davim, J.P. , Reis, P. and Conceição António, C. (2004). Experimental Study of Drilling Glass Fiber Reinforced Plastics (GFRP) Manufactured By Hand Lay-up , Composites Science and Technology, 64: 289-297.

13.

El-Sonbaty, I. , Khashaba, U.A. and Machaly, T. (2004). Factors Affecting the Machinability of GFR/Epoxy Composites, Composite Structures , 63(3-4): 329-338.

14.

Khashaba, U.A. (2004). Delamination in Drilling GFR-Thermoset Composites, Composite Structures, 63: 313-327.

15.

Kistler Instrument AG Winterthur (1995). 3-Component Dynamometer Fx, Fy, Fz, Nr. 6.9257BA, Ed. 11.95: 1-4.

16.

Sreejith, P.S. , Krishnamurthy, R. , Malhotra, S.K. and Narayanasamy , K. (2000). Evaluation of PCD Tool Performance During Machining of Carbon/Phenolic Ablative Composites, Journal of Materials Processing Technology, 104: 53-58.