Preparation and mechanical properties of thermosetting epoxy foams based on epoxy/ 2-ethyl-4-methylimidazol system with different curing agent contents

Abstract

Epoxy/2-ethyl-4-methylimidazol system with different curing agent content was completely cured for foaming, and the effect of a systematic variation in 2-ethyl-4-methylimidazol content on the crosslinking density of cured epoxy resins was investigated. It was found that the crosslinking density of completed cured epoxy reduced as the 2-ethyl-4-methylimidazol content increased in certain range of contents (10–50 mol%). Then the precursors were foamed by a batch foaming process with supercritical carbon dioxide. The cellular morphologies of foamed epoxy resins were analyzed by scanning electron microscopy. The results revealed that the reduced crosslinking density would improve the foamability of cured epoxy resin. The microcellular epoxy foams could be obtained by maintaining a moderate crosslinking density, which can be controlled by varying 2-ethyl-4-methylimidazol content. For the completely cured epoxy with different curing agent content, when the crosslinking density of epoxy resin was 232.40 mol m^–3 (the 2-ethyl-4-methylimidazol content was 35 mol%) or lower, microcellular structure was obtained by adjusting the foaming conditions. The effects of foaming on the mechanical properties were also discussed. The results indicated that microcellular epoxy foams had higher impact strength but lower tensile strength and tensile modulus, validating that the introduction of microcellular structure in epoxy matrix was conducive to the improvement of the ductility of epoxy foams.

Keywords

Epoxy microcellular foams curing agent content crosslinking density mechanical properties

Get full access to this article

View all access options for this article.

References

Ito

Semba

Taki

et al.

Effect of the molecular weight between crosslinks of thermally cured epoxy resins on the CO₂-bubble nucleation in a batch physical foaming process. J Appl Polym Sci 2014; 131: 40407–40414.

Takiguchi

Ishikawa

Sugimoto

et al.

Effect of rheological behavior of epoxy during precuring on foaming. J Appl Polym Sci 2008; 110: 657–662.

Yang

et al.

Synthesis of cyanate ester microcapsules via solvent evaporation technique and its application in epoxy resins as a healing agent. Ind Eng Chem Res 2016; 55: 10941–10946.

Altuna

Ruseckaite

Stefani

. Biobased thermosetting epoxy foams: mechanical and thermal characterization. ACS Sustain Chem Eng 2015; 3: 1406–1411.

Zhang

Yan

Zheng

et al.

Tough grapheme-polymer microcellular foams for electromagnetic interference shielding. ACS Appl Mater Interfaces 2011; 3: 918–924.

Fan

Tian

Chen

et al.

Preparation and characterization of cyanate/epoxy foam. High Perform Polym 2016; 28: 96–109.

Ren

et al.

Development of epoxy foaming with CO₂ as latent blowing agent and principle in selection of amine curing agent. Ind Eng Chem Res 2015; 54: 11056–11064.

Mondy

Rao

Moffat

et al.

Structural epoxy foams, in epoxy polymers: new materials and innovations, Wiley-VCH: Weinheim, 2010, pp. 303–324.

Quadrini

Squeo

. Solid-state foaming of epoxy resin. J Cell Plast 2008; 44: 161–173.

10.

Wang

Yang

Jiang

et al.

Cell morphology, bubbles migration, and flexural properties of non-uniform epoxy foams using chemical foaming agent. J Appl Polym Sci 2014; 131: 41175–41175.

11.

Kinyanjui

Hatchett

. Thermally induced changes in the chemical and mechanical properties of epoxy foam. J Cell Plast 2010; 46: 531–549.

12.

Stefani

Barchi

Sabugal

et al.

Characterization of epoxy foams. J Appl Polym Sci 2003; 90: 2992–2996.

13.

Jain

Choudhary

Narula

. Curing and thermal behaviour of epoxy resin in the presence of pyromellitic dianhydride and imidazole. J Appl Polym Sci 2007; 106: 2593–2598.

14.

Ooi

Cook

Simon

et al.

DSC studies of the curing mechanisms and kinetics of DGEBA using imidazole curing agents. Polymer 2000; 41: 3639–3649.

15.

Wang

Zhao

Ling

et al.

The effect of curing cycles on curing reactions and properties of a ternary system based on benzoxazine, epoxy resin, and imidazole. J Appl Polym Sci 2013; 127: 2169–2175.

16.

Ogata

Kinjo

Kawata

. Effects of crosslinking on physical properties of phenol-formaldehyde novolac cured epoxy resins. J Appl Polym Sci 1993; 48: 583–601.

17.

Heise

Martin

. Curing mechanism and thermal properties of epoxy-imidazole systems. Macromolecules 1989; 22: 99–104.

18.

Heise

Martin

. Mechanism of 2-ethyl-4-methylimidazole in the curing of the diglycidyl ether of bisphenol A. J Polym Sci Part C: Polym Lett 1988; 26: 153–157.

19.

Hart

Sottos

White

. Repeatable self-healing of an epoxy matrix using imidazole initiated polymerization. Polymer 2015; 67: 174–184.

20.

Lyu J, Liu T, Xi Z, et al. Effect of pre-curing process on epoxy resin foaming using carbon dioxide as blowing agent. J Cell Plast 2016. DOI: 10.1177/0021955X16639235.

21.

Salerno

Zeppetelli

Di Maio

et al.

Design of bimodal PCL and PCL-HA nanocomposite scaffolds by two step depressurization during solid-state supercritical CO₂ foaming. Macromol Rapid Commun 2011; 32: 1150–1156.

22.

Chen

Rende

Schadler

et al.

Polymer nanocomposite foams. J Mater Chem A 2013; 1: 3837–3850.

23.

Zhang

Yang

et al.

Fabrication of microcellular polycarbonate foams with unimodal or bimodal cell-size distributions using supercritical carbon dioxide as a blowing agent. J Cell Plast 2014; 50: 55–79.

24.

Zhang

Shi

et al.

Microcellular foaming of poly(phenylene sulfide)/poly(ether sulfones) blends using supercritical carbon dioxide. J Appl Polym Sci 2015; 132: 42634–42647.

25.

Zhang

Yang

et al.

Mechanical and dielectric properties of microcellular polycarbonate foams with unimodal or bimodal cell-size distributions. J Cell Plast 2015; 51: 307–327.

26.

Garcia

Soares

. Determination of the epoxide equivalent weight of epoxy resins based on diglycidyl ether of bisphenol A (DGEBA) by proton nuclear magnetic resonance. Polym Test 2003; 22: 51–56.

27.

Kenyon

Nielsen

. Characterization of network structure of epoxy resins by dynamic mechanical and liquid swelling tests. J Macromol Sci: Chem 1969; 3: 275–295.

28.

Xing

Wang

et al.

Preparation of microcellular polystyrene/polyethylene alloy foams by supercritical CO₂ foaming and analysis by X-ray microtomography. J Supercrit Fluids 2013; 82: 50–55.

29.

Liang

Dang

et al.

Ideal dielectric thermally conductive bismaleimide nanocomposites filled with polyhedral oligomeric silsesquioxane functionalized nanosized boron nitride. RSC Adv 2016; 6: 35809–35814.

30.

Case

O'Brien

Ward

. Cure profiles, crosslink density, residual stresses, and adhesion in a model epoxy. Polymer 2005; 46: 10831–10840.

31.

Ghaemy

Sadjady

. Kinetic analysis of curing behavior of diglycidyl ether of bisphenol A with imidazoles using differential scanning calorimetry techniques. J Appl Polym Sci 2006; 100: 2634–2641.

32.

Heise

Martin

. Analysis of the cure kinetics of epoxy/imidazole resin systems. J Appl Polym Sci 1990; 39: 721–738.

33.

Yao

Chen

et al.

Numerical simulation of polypropylene foaming process assisted by carbon dioxide: Bubble growth dynamics and stability. Chem Eng Sci 2011; 66: 3656–3665.

34.

Yao

Chen

et al.

High melt strength polypropylene by ionic modification: preparation, rheological properties and foaming behaviors. Polymer 2015; 70: 207–214.

35.

Sun

Sur

Mark

. Microcellular foams from polyethersulfone and polyphenylsulfone: preparation and mechanical properties. Eur Polym J 2002; 38: 2373–2381.

36.

Doroudiani

Kortschot

. Polystyrene foams. II. Structure-impact properties relationships. J App. Polym Sci 2003; 90: 1421–1426.

37.

Bao

Junior

Weng

et al.

Tensile and impact properties of microcellular isotactic polypropylene (PP) foams obtained by supercritical carbon dioxide. J Supercrit Fluids 2016; 111: 63–73.