Injection molded components with functionally graded foam structures

Abstract

In the past few years, foam injection molding has increasingly gained significance in the field of technical plastic components. This is due to the development of new processes and processing combinations and efforts to produce lightweight products. In this article, a special tool technology will be introduced, which aids the process of expanding the existing areas of applications. The technology enables the production of foam injection molded components with different foaming ratios. This is made possible by core movements in the closed injection mold after the cavity has been filled volumetrically with plastic melt containing blowing agent. In doing so, functionally graded components with locally differing properties can be produced in one processing step. The method (pull and foam method) is based on the idea of equipping thin-walled components with locally foamed thick-volume elements – i.e. to increase the stiffness, create spacers, or joining surfaces. Simultaneously this method aims to exceed the limitations of conventional foam injection molding, especially with regard to scope for design. This article describes the procedure and characteristics of the process. Results with regard to the density in the differentially foamed areas, the morphology and the mechanical properties in correlation with the essential processing parameters are given.

Keywords

Foam injection molding precision mold opening breathing mold pull and foam local foaming functional gradation core pulling foam density foam morphology bending properties

Get full access to this article

View all access options for this article.

References

Kirschling H. Mikroschäume aus Polycarbonat / Microcellular foams of polycarbonate. PhD Thesis, University of Kassel, Germany, 2009.

Bledzki

Rohleder

Kirschling

. Correlation between morphology and notched impact strength of microcellular foamed polycarbonate. J Cell Plast 2010; 46: 415–440.

Flórez Sastre L. Influence of the foam morphology on the mechanical properties of structural foams. PhD Thesis, University of Aachen, Germany, 2011.

Michaeli

Flórez

Oberloer

. Schaumdesign / Foam design. Plastverarbeiter 2009; 4: 80–82.

Michaeli

Florez

Oberloer

. Analysis of the impact properties of structural foams. J Cell Plast 2009; 45: 321–321.

Spörrer A. Leichte Integralschaumstrukturen durch Spritzgießen mit optimierten Werkstoffen und variothermen Werkzeugen / Lightweight structural foams by injection molding with optimized materials and variotherm tools. PhD Thesis, University of Bayreuth, Germany, 2010.

Spörrer A. The challenge of foam injection moulding – possibilities to improve surface appearance, foam morphology and mechanical properties. In: Blowing agents and foaming processes 2007 (Smithers Rapra), Frankfurt (Main), Germany, 22–23 May 2007, paper no 16.

Spörrer

Altstädt

. Controlling morphology of injection molded structural foams by mold design and processing parameters. J Cell Plast 2007; 43: 313–313.

Müller

Ehrenstein

. Evaluation and modeling of injection-molded rigid polypropylene integral foam. J Cell Plast 2004; 40: 45–45.

10.

Müller N. Spritzgegossene Integralschaumstrukturen mit ausgeprägter Dichtereduktion / Injection molded integral foams with pronounced density-reduction. PhD Thesis, University of Erlangen-Nuremberg, Germany, 2006.

11.

Lee JWS, Wang J, Kim SG, et al. Advanced structural foam molding of various PPs with gas counterpressure and mold opening. In: Polymer foam 2007 (AMI), Newark, NJ, USA, 2–3 October 2007, pp. 1–14.

12.

Kühn-Gajdzik J. Amorphe und teilkristalline Mikroschäume im Spritzgießverfahren / Amorphous and semi-crystalline microcellular foams by injection molding. PhD Thesis, University of Kassel, Germany, 2011.

13.

Heim

H-P

Schnieders

Jarka

. Geschäumte Rippen für dünnwandige Teile / Foamed ribs for thin-walled components. Kunststoffe 2011; 9: 48–50.

14.

Heim H-P, Tromm M, Jarka S, et al. Pull and foam - Injection moulding method: Foamed ribs for stiffening plane components. In: ANTEC (SPE), Orlando, FL, USA, 2–4 April 2012, pp. 2477–2480.

15.

Heim H-P and Tromm M. Pull and foam – method: First investigations with chemical and physical blowing agents. In: 10th International conference on foam materials & technology, FOAMS (SPE), Barcelona, Spain, 12–13 September 2012.

16.

Heim H-P, Bledzki AK, Rohleder M, et al. Thermo-mechanically graded injection moulded microcellular foams. In: 1st International conference on thermo-mechanically graded materials, Kassel, Germany, 29–30 October 2012, pp. 231–240.

17.

Heim H-P, Beldzki AK, Rohleder M, et al. Formation of foam structures and influence of processing procedure in foam injection moulding of thermoplastic materials. In: 2nd International conference on cellular materials, Dresden, Germany, 7–9 November 2012.

18.

Heim H-P and Tromm M. Formation of morphology as a function of process control by foam injection molding of a functionally graded components. In: ANTEC (SPE), Las Vegas, NV, USA, 28–30 April 2014, pp. 1551–1556.

19.

Heim H-P and Tromm M. General aspects of foam injection molding using local precision mold opening technology. Polymer 2015; 56: 111–118.

20.

Gómez-Gómez

Arencón

Sánchez-Soto

MÁ

. Influence of the injection moulding parameters on the microstructure and thermal properties of microcellular polyethylene terephthalate glycol foams. J Cell Plast 2013; 49(1): 47–63.

21.

Liao

Zhou

. Rheological control in foaming polymeric materials: II. Semi-crystalline polymers. Polymer 2010; 51: 6334–6345.

22.

Roch

Menrath

Huber

. Fiber reinforced thermoplastics in sandwich construction. Kunststoffe Int 2013; 10: 119–124.

Injection molded components with functionally graded foam structures – Procedure and essential results

Abstract

Keywords

Get full access to this article

References