The electrodeposited antimony-copper coatings demonstrate a varying degree of chemical and structural heterogeneity that determines their corrosion behaviour in 0.5M sodium chloride. The electrochemical and corrosion properties of layers at open circuit potential were investigated by electrochemical impedance spectroscopy and optical surface observation. Corrosion polarisation tests revealed that anodic behaviour of Sb–Cu alloys is similar for the all tested samples and depends on the antimony chemical resistance. Under anodic polarisation up to about −0.03 VAg/AgCl a multistep process of anodic oxide film transformation was registered. The observations by SEM revealed that at a higher anodic polarisation many submicron-sized pits are formed. The formation of microgalvanic corrosion cells results in preferential dissolution of the antimony phase at both OCP and anodic polarisation.
DardenizG.Why did the use of antimony-bearing alloys in bronze age anatolia fall dormant after the early bronze age?: a case from resuloğlu (Cё orum, Turkey). PLoS ONE 2020; 15(7):e0234563, doi:10.1371/journal.pone.0234563
2.
KuijpersMHG, BraekmansD, BergerD.Quantitative comparisons of the color of CuAs, CuAs, CuNi, and CuSb alloys. J Archaeol Sci. 2017;88:14–23. doi:10.1016/j.jas.2017.09.001
3.
SandanaYN, SinghJP, KumarR.Electrodeposion of antimony and antimony and antimony alloys – a review. Surf Techn. 1985;24:319–353. doi:10.1016/0376-4583(85)90053-6
4.
JacksonED, MosbyJM, PrietoAL.Evaluation of the electrochemical properties of crystalline copper antimonide thin film anodes for lithium ion batteries produced by single step electrodeposition. Electrochim Acta. 2016;214:253–264. doi:10.1016/j.electacta.2016.07.126
5.
ZhangC, XuK-Q, ZhouW, . Copper–antimony alloy–nanoparticle clusters supported on porous cu networks for electrochemical energy storage. Part Part Syst Charact. 2016;33:553–559. doi:10.1002/ppsc.201500198
6.
SchulzeMC, SchulzeRK, PrietoAL.Electrodeposited thin-film CuxSb anodes for Li-ion batteries: enhancement of cycle life via tuning of film composition and engineering of the film-substrate interface. J Mater Chem A. 2018;6:12708–12717. doi:10.1039/C8TA01798K
7.
ArpacıkM, BiçerM, Şişmanİ. Influence of microstructure on the electrochemical performance of Sn-Sb-Cu nanostructures as anode materials for lithium-ion battery. J Electrochem Soc. 2013;160:A2251–A2257. doi:10.1149/2.100311jes
8.
BaggettoL, AllcornE, ManthiramA, . Cu2Sb thin films as anode for Na-ion batteries. Electrochem Commun. 2013;27:168–171. doi:10.1016/j.elecom.2012.11.030
9.
HeY, SunW.Carbon-coated SbCu alloy nanoparticles for high performance lithium storage. J Alloys Compd. 2018;753:371–377. doi:10.1016/j.jallcom.2018.04.183
WangW, ZhiG, LiuL, . Preparation of rod-like CuSbS2 particles by soft-template synthesis and electrochemical performance toward lithium storage. J Nanopart Res. 2022;24; doi:10.1007/s11051-022-05481-9
12.
KhairyM, JiangP, BouletP, . Electron density and optoelectronic properties of copper antimony sulphur ternary compounds for photovoltaic applications. J Electron Mater. 2022;51:3903–3918. doi:10.1007/s11664-022-09650-3
13.
MoujoudS, HartitiB, TouhtouhS, . Efficiency enhancement by simulation method of copper antimony disulfide thin film based solar cells. Mater Today Commun. 2022;31:103415, doi:10.1016/j.mtcomm.2022.103415
14.
AimeiZ, YanpingW, BingL, . Sulfurization of electrodeposited Sb/Cu precursors for CuSbS2: potential absorber materials for thin-film solar cells. Front Mater. 2022;8:818596, doi:10.3389/fmats.2021.818596
15.
PenezkoA, Kauk-KuusikM, VolobujevaO, . Properties of Cu-Sb-Se thin films deposited by magnetron co-sputtering for solar cell applications. Thin Solid Films. 2021;740:139004, doi:10.1016/j.tsf.2021.139004
16.
ZakiSA, Abd-ElrahmanMI, Abu-SehlyAA, . Solar cell fabrication from semiconducting Cu3SbS3 on n-Si: parameters evolution. Mater Sci Semicond Proc. 2020;115:105123, doi:10.1016/j.mssp.2020.105123
17.
OubakallaM, BeraichM, TaibiM, . The choice of the copper concentration favoring the production of stoichiometric CuSbS2 and Cu12Sb4S13 thin films co-electrodeposited on FTO. J Alloys Compd. 2022;908:164618, doi:10.1016/j.jallcom.2022.164618
18.
WikstromLL, NobeK.Potentiodynamic studies of antimony in acidic and alkaline solutions. Corrosion. 1975;31:364–369. doi:10.5006/0010-9312-31.10.364
19.
PavlovD, BojinovM, LaitinenT, . Electrochemical behaviour of the antimony electrode in sulphuric acid solutions – I. Corrosion processes and anodic dissolution of antimony. Electrochim Acta. 1991;36:2081–2086. doi:10.1016/0013-4686(91)85213-Q
20.
PavlovD, BojinovM, LaitinenT, . Electrochemical behaviour of the antimony electrode in sulphuric acid solutions – II. Formation and properties of the primary anodic layer. Electrochim Acta. 1991;36:2087–2092. doi:10.1016/0013-4686(91)85214-R
21.
GlabS, EdwallG, JöngrenP-A, . Cyclic voltammetric studies on a monocrystalline antimony electrode. Electrochim Acta. 1982;27:581–586. doi:10.1016/0013-4686(82)85043-3
22.
LiuY, LiuH, YaoZ, . Fabrication, improved performance, and response mechanism of binary Ag-Sb alloy pH electrodes. Electrochim Acta. 2020;337:135746, doi:10.1016/j.electacta.2020.135746
23.
TapiaMA, Pérez-RàfolsC, PaštikaJ, . Antimony nanomaterials modified screen-printed electrodes for the voltammetric determination of metal ions. Electrochim Acta. 2022;425:140690, doi:10.1016/j.electacta.2022.140690
24.
MaczugaM, EconomouA, BobrowskiA, . Novel screen-printed antimony and tin voltammetric sensors foranodic stripping detection of Pb(II) and Cd(II). Electrochim Acta. 2013;114:758–765. doi:10.1016/j.electacta.2013.10.075
25.
IzquierdoJ, NagyL, VargaÁ, . Spatially resolved measurement of electrochemical activity and pH distributions in corrosion processes by scanning electrochemical microscopy using antimony microelectrode tips. Electrochim Acta. 2011;56:8846–8850. doi:10.1016/j.electacta.2011.07.076
26.
BojinovM, PavlovD.Anodic oxidation of antimony at high overpotentials - formation of a barrier layer and klebelsbergite. J Electroanal Chem. 1993;346:339–352. doi:10.1016/0022-0728(93)85023-A
27.
LaitinenL, RevitzerH, SundholmG, . Electrochemical behaviour of the antimony electrode in sulphuric acid solutions—III. identification of corrosion products after long-term polarization. Electrochim Acta. 1991;36:2093–2102. doi:10.1016/0013-4686(91)85215-S
28.
MogodaAS, Abd EI-HaleemTM.Electrochemical behavior of antimony in sulfuric acid and sodium sulfate solutions containing potassium dichromate. Corrosion. 2003;59:3–10. doi:10.5006/1.3277534
29.
ItoCR, NobeK.Chloride ion effects in the corrosion kinetics of intermetallics in acidic solutions. ECS Transaction. 2009;16:217–226. doi:10.1149/1.3229969
30.
SoltisJ, LichtiKA.Galvanic corrosion of carbon steel coupled to antimony. Corr Sci. 2013;68:162–167. doi:10.1016/j.corsci.2012.11.008
31.
GulevskiiVA, AntipovVI, VinogradovLV, . Development of antimony_based impregnating alloys to produce electrographite frame composite materials. Russ Metall. 2011;2011:78–84. doi:10.1134/S0036029511010095
32.
WuBY, LiangW, WangAH.Compositional design of low carbon sulphuric acid dewpoint corrosion resistant steel and corresponding anticorrosive mechanism. Corros Eng Sci Technol. 2013;48:313–320. doi:10.1179/1743278212Y.0000000071
33.
LinsVFC, SoaresRB, AlvarengaEA.Corrosion behaviour of experimental copper–antimony–molybdenum carbon steels in industrial and marine atmospheres and in a sulphuric acid aqueous solution. Corros Eng Sci Technol. 2017;52:397–403. doi:10.1080/1478422X.2017.1305537
34.
DiasM, VerissimoNC, RegoneNN, . Electrochemical corrosion behaviour of Sn–Sb solder alloys: the roles of alloy Sb content and type of intermetallic compound. Corros Eng Sci Technol. 2021;56:11–21. doi:10.1080/1478422X.2020.1791446
35.
KostovV, DobrovolskaT.Structure formation and multilayering in electrodeposited copper-antimony alloy. Port Electrochim Acta. 2023;41, 335–346. (in press). doi:10.4152/pea.2023410502
36.
ChenX, QianH, LouY, . Effects of Cu-content and passivation treatment on the corrosion resistance of Al0.3CuxCoCrFeNi high-entropy alloys. J Alloys Compd. 2022;920:165956, doi:10.1016/j.jallcom.2022.165956
37.
FürtauerS, FlandorferH.A new experimental phase diagram investigation of Cu–Sb. Monatsh Chem. 2012;143:1275–1287. doi:10.1007/s00706-012-0737-1
38.
Estrada-VargasA, CasillasN, Gomez-SalazarS, . Corrosion of aluminum, copper, brass and stainless steel 304 in tequila. Int J Electrochem Sci. 2012;7:7877–7887. doi:10.1016/S1452-3981(23)17961-2
NaseerA., KhanA.Y.A study of growth and breakdown of passive film on copper surface by electrochemical impedance spectroscopy. Turk J Chem. 2009;33:739–750. doi:10.3906/kim-0708-23
LaschukNO, Bradley EastonE, ZenkinaOV.Reducing the resistance for the use of electrochemical impedance spectroscopy analysis in materials chemistry. RSC Adv. 2021;11:27925–27936. doi:10.1039/D1RA03785D
43.
ManhaboscoTM, TamborimSM, dos SantosCB, . Tribological, electrochemical and tribo-electrochemical characterization of bare and nitrided Ti6Al4V in simulated body fluid solution. Corr Sci. 2011;53:1786–1793. doi:10.1016/j.corsci.2011.01.057
44.
GaoP, ZhangC, WenG.Equivalent circuit model analysis on electrochemical impedance spectroscopy of lithium metal batteries. J Power Sources. 2015;294:67–74. doi:10.1016/j.jpowsour.2015.06.032
45.
NikitinaVA, ZakharkinMV, VassilievSY, . Lithium ion coupled electron-transfer rates in superconcentrated electrolytes: exploring the bottlenecks for fast charge-transfer rates with LiMn2O4 cathode materials. Langmuir. 2017;33:9378–9389. doi:10.1021/acs.langmuir.7b01016
46.
BrettCMA.Electrochemical impedance spectroscopy in the characterisation and application of modified electrodes for electrochemical sensors and biosensors. Molecules. 2022;27:1497, doi:10.3390/molecules27051497
47.
BraithwaiteL, AlbrechtasK, ZagidulinD, . Galvanic coupling of copper and carbon steel in the presence of bentonite clay and chloride. J Electrochem Soc. 2022;169:051502, doi:10.1149/1945-7111/ac5ff2
48.
KimC-H, PyunS-I, KimJ-H.An investigation of the capacitance dispersion on the fractal carbon electrode with edge and basal orientations. Electrochim Acta. 2003;48:3455–3463. doi:10.1016/S0013-4686(03)00464-X
49.
CaoF, WeiJ, DongJ, . The corrosion inhibition effect of phytic acid on 20SiMn steel in simulated carbonated concrete pore solution. Corros Sci. 2015;100:365–376. doi:10.1016/j.corsci.2015.08.020
50.
MultaniRS, FeldmannT, DemopoulosGP.Antimony in the metallurgical industry: a review of its chemistry and environmental stabilization options. Hydrometallurgy. 2016;164:141–153. doi:10.1016/j.hydromet.2016.06.014
51.
LuoW, ZhouJ, XuY, . Preparation and electrochemical corrosion behaviour of 3D large-sized nanocrystalline copper bulk in solutions with chloride ions. Corros Eng Sci Technol. 2019;54:541–545. doi:10.1080/1478422X.2019.1636176
52.
PérezOE, PérezMA, TeijeloML.Characterization of the anodic growth and dissolution of antimony oxide films. J Electroanal Chem. 2009;632:64–71. doi:10.1016/j.jelechem.2009.03.018
53.
HeY, XuR, HeS, . Effect of NaNO3 concentration on anodic electrochemical behavior on the Sb surface in NaOH solution. Int J Miner Metall Mater. 2018;25:288–299. doi:10.1007/s12613-018-1572-0
54.
HaynesWM.CRC handbook of chemistry and physics. 95th ed. Boca Raton (FL): CRC Press LLC; 2014-2015; p. 4-48 and p. 4-61.
55.
GirginovC, LilovE, KozhukharovS, . Efficiency of the galvanostatic formation of anodic antimony oxide in oxalic acid solutions. Port Electrochim Acta. 2022;40:89–98. doi:10.4152/pea.2022400203
56.
Veys-RenauxD, DrevetR, PetitjeanC, . Electrochemical behavior of CoSb3 in sulfuric and oxalic acids over the potential range 0 to 40 V. J Solid State Electrochem. 2018;22:2821–2828. doi:10.1007/s10008-018-3990-3
57.
MogodaAS, Abd El-HaleemTM.Anodic oxide film formation on antimony and its currentless dissolution in sulphuric acid containing some monocarboxylic acids. Thin Solid Films. 2003;441:6–12. doi:10.1016/S0040-6090(03)00876-9
58.
SchmukiP, SantinacciL, LockwoodDJ, . Formation of porous layers on InSb(100) by anodization. Phys Status Solidi (A) Appl. Res. 2003;197:71–76. doi:10.1002/pssa.200306470
