The influence of sensitisation heat treatment, surface roughness and repetitive cyclic voltammetry (RCV) procedure (that was used to create passive films on the surface of sensitised samples) on the corrosion behaviour of UNS S31803 duplex stainless steel was evaluated using sodium hydroxide etching, double-loop electrochemical potentiodynamic reactivation (DLEPR), potentiodynamic polarisation, Mott–Schottky analysis, X-ray diffraction and optical microscopy techniques. The results showed that prolonged sensitisation time leads to the formation of defective passive films on the surface. In addition, as the substrate surface roughness decreases, the defect concentration in the resulting passive film decreases. Moreover, thick passive films that were created at a high number of RCV cycles contain fewer defects than the thin ones. Finally, the specimens with smooth surfaces, thick passive films and low degree of sensitisation exhibit high corrosion resistance due to their intact passive layers formed on their surfaces.
ASM Handbook, Volume 1: Properties and Selection: Irons, Steels, and High-Performance Alloys, Product code: 06181G | ISBN: 978-0-87170-377-4. 2005.
2.
GoodwinSQuayleBNobleF.Polarization behavior of austenitic and duplex stainless steels in the double loop reactivation test. Corrosion. 1987; 43 (12): 743–747. doi: 10.5006/1.3583863
3.
LopezNCidMPuiggaliMApplication of double loop electrochemical potentiodynamic reactivation test to austenitic and duplex stainless steels. Mater Sci Eng A. 1997; 229 (1-2): 123–128. doi: 10.1016/S0921-5093(97)00008-7
4.
KimJ-SKwonH-S.Effects of tungsten on corrosion and kinetics of sigma phase formation of 25% chromium duplex stainless steels. Corrosion. 1999; 55 (5): 512–521. doi: 10.5006/1.3284014
5.
ChenTYangJ.Effects of solution treatment and continuous cooling on σ-phase precipitation in a 2205 duplex stainless steel. Mater Sci Eng A. 2001; 311 (1-2): 28–41. doi: 10.1016/S0921-5093(01)00911-X
6.
ArıkanMEArıkanRDorukM.Determination of susceptibility to intergranular corrosion of UNS 31803 type duplex stainless steel by electrochemical reactivation method: a comparative study. Int J Corros. 2012; 2012: 1–14.
7.
LopezNCidMPuiggaliM.Influence of o-phase on mechanical properties and corrosion resistance of duplex stainless steels. Corros Sci. 1999; 41 (8): 1615–1631. doi: 10.1016/S0010-938X(99)00009-8
8.
Morshed-BehbahaniKPakshirM.Effect of different degrees of sensitization on the EIS response of 316L and 316 SS in transpassive region. J Mater Eng Perform. 2014; 23 (6): 2283–2292. doi: 10.1007/s11665-014-1018-4
9.
Morshed-BehbahaniKPakshirM.The effect of solution-annealing on the EIS response of AISI 316 SS with different degrees of sensitization in the transpassive region. Prot Met Phys Chem Surf. 2015; 51 (6): 1027–1033. doi: 10.1134/S2070205115060039
10.
Morshed-BehbahaniKPakshirMAbbasiZDamage mechanism at different transpassive potentials of solution-annealed 316 and 316l stainless steels. Int J Miner Metall Mater. 2015; 22 (22): 45–51. doi: 10.1007/s12613-015-1042-x
11.
ASTM, ASTM G108-92, Standard test method for electrochemical reactivation (EPR) for detecting sensitization of AISI type.
12.
ASTM, ASTM A262, Standard practices for detecting susceptibility to intergranular attack in austenitic Stainless steels; 1993.
13.
ASTM, ASTM A923-03, Standard test methods for detecting detrimental intermetallic phases in duplex austenitic/ferritic stainless steel; 2003.
14.
ASTM, ASTM G150, Standard test method for electrochemical critical pitting temperature testing of stainless steels. 2010.
15.
ASTM, ASTM G102-89(2015), standard practice for calculation of corrosion rates and related information from electrochemical measurements; 2015.
Morshed-BehbahaniKNajafisayarPPakshirM.Study of the intergranular corrosion of sensitized UNS S31803 stainless steel in transpassive region. J Mater Eng Perform. 2016; 25 (8): 3418–3429. doi: 10.1007/s11665-016-2176-3
18.
SunJSunLDaiN. Investigation on ultra-pure ferritic stainless steel 436L susceptibility to intergranular corrosion using optimised double loop electrochemical potentiokinetic reactivation method. Corros Eng Sci Technol. 2018: 1–8. doi: 10.1080/1478422X.2018.1512222
19.
CabriniMCigadaARondellGEffect of different surface finishing and of hydroxyapatite coatings on passive and corrosion current of Ti6Al4V alloy in simulated physiological solution. Biomaterials. 1997; 18 (11): 783–787. doi: 10.1016/S0142-9612(96)00205-0
20.
LiWLiD.Influence of surface morphology on corrosion and electronic behavior. Acta Mater. 2006; 54 (2): 445–452. doi: 10.1016/j.actamat.2005.09.017
21.
VafaeianSFattah-alhosseiniAKeshavarzMKSimultaneous investigation of the effect of advanced thermomechanical treatment and repetitive cyclic voltammetry on the electrochemical behavior of AISI 430 ferritic stainless steel. J Mater Eng Perform. 2017; 26 (2): 676–684. doi: 10.1007/s11665-017-2509-x
22.
ShahryariAKamalWOmanovicS.The effect of surface roughness on the efficiency of the cyclic potentiodynamic passivation (CPP) method in the improvement of general and pitting corrosion resistance of 316LVM stainless steel. Mater Lett. 2008; 62 (23): 3906–3909. doi: 10.1016/j.matlet.2008.05.032
23.
ShahryariAAzariFValiHThe positive influence of electrochemical cyclic potentiodynamic passivation (CPP) of a SS316LS surface on its response to fibronectin and pre-osteoblasts. Phys Chem Chem Phys. 2009; 11 (29): 6218–6224. doi: 10.1039/b902881a
24.
ShahryariAOmanovicSSzpunarJA.Enhancement of biocompatibility of 316LVM stainless steel by cyclic potentiodynamic passivation. J Biomed Mater Res A. 2009; 89A (4): 1049–1062. doi: 10.1002/jbm.a.32053
25.
FujimotoSTsuchiyaH.Semiconductor properties and protective role of passive films of iron base alloys. Corros Sci. 2007; 49 (1): 195–202. doi: 10.1016/j.corsci.2006.05.020
26.
FengZChengXDongCPassivity of 316L stainless steel in borate buffer solution studied by Mott–schottky analysis, atomic absorption spectrometry and X-ray photoelectron spectroscopy. Corros Sci. 2010; 52 (11): 3646–3653. doi: 10.1016/j.corsci.2010.07.013
27.
TaveiraLVMontemorMFDa Cunha BeloMInfluence of incorporated Mo and Nb on the Mott–schottky behaviour of anodic films formed on AISI 304L. Corros Sci. 2010; 52 (9): 2813–2818. doi: 10.1016/j.corsci.2010.04.021
28.
MontemorMSimõesAFerreiraMThe role of Mo in the chemical composition and semiconductive behaviour of oxide films formed on stainless steels. Corros Sci. 1999; 41 (1): 17–34. doi: 10.1016/S0010-938X(98)00126-7
29.
CottisR.GrahamM.LindsayR.. 2010. Shreir's corrosion - vol 3 (corrosion and degradation of engineering materials).
30.
HakikiNBoudinSRondotBThe electronic structure of passive films formed on stainless steels. Corros Sci. 1995; 37 (11): 1809–1822. doi: 10.1016/0010-938X(95)00084-W
31.
LeeE-JPyunS-I.Analysis of nonlinear Mott-Schottky plots obtained from anodically passivating amorphous and polycrystalline TiO2 films. J Appl Electrochem. 1992; 22 (2): 156–160. doi: 10.1007/BF01023817
32.
Fattah-alhosseiniAAghamohamadiHSafaAB.Electrochemical behavior assessment of Alloy 22 (UNS N06022) in hydrochloric acid solutions by electrochemical impedance spectroscopy and Mott– Schottky analyses. Anal Bioanal Electrochem. 2015; 7 (6): 728–738.
33.
Fattah-AlhosseiniA.Int J ISSI. 2013; 10 (2): 1–6.
34.
Fattah-alhosseiniAVafaeianS.Effect of solution pH on the electrochemical behaviour of AISI 304 austenitic and AISI 430 ferritic stainless steels in concentrated acidic media. Egypt J Petroleum. 2015; 24 (3): 333–341. doi: 10.1016/j.ejpe.2015.07.016
35.
CarmezimMSimoesAMontemorMCapacitance behaviour of passive films on ferritic and austenitic stainless steel. Corros Sci. 2005; 47 (3): 581–591. doi: 10.1016/j.corsci.2004.07.002
36.
BabićRMetikoš-HukovićM.Semiconducting properties of passive films on AISI 304 and 316 stainless steels. J Electroanal Chem. 1993; 358 (1-2): 143–160. doi: 10.1016/0022-0728(93)80435-K
37.
Fattah-AlhosseiniAGolozarMSaatchiAEffect of solution concentration on semiconducting properties of passive films formed on austenitic stainless steels. Corros Sci. 2010; 52 (1): 205–209. doi: 10.1016/j.corsci.2009.09.003
38.
AmadouTSidhomHBrahamC.Double loop electrochemical potentiokinetic reactivation test optimization in checking of duplex stainless steel intergranular corrosion susceptibility. Metall Mater Trans A. 2004; 35 (11): 3499–3513. doi: 10.1007/s11661-004-0187-4
39.
HsiehCCWuW.Overview of Intermetallic Sigma Phase Precipitation in Stainless Steels. ISRN Metallurgy. 2012; 2012 (1): 1–16.
40.
GowJTHarderOE.1942. Balancing the composition of cast 25 per cent chromium-12 per cent nickel type alloys.
41.
AzumiKOhtsukaTSatoN.Mott-Schottky plot of the passive film formed on iron in neutral borate and phosphate solutions. J Electrochem Soc. 1987; 134 (6): 1352–1357. doi: 10.1149/1.2100672
42.
VukovićM.The formation and growth of hydrous oxide film on stainless steel in alkaline solution by potential cycling. Corros Sci. 1995; 37 (1): 111–120. doi: 10.1016/0010-938X(94)00119-Q
43.
HakikiNBeloMDCSimoesASemiconducting properties of passive films formed on stainless steels. J Electrochem Soc. 1998; 145 (11): 3821–3829. doi: 10.1149/1.1838880
44.
HaH-YLeeT-H.Determining factors for the protectiveness of the passive film of FeCrN stainless steel formed in sulfuric acid solutions. Corros Sci Technol. 2013; 12 (4): 163–170. doi: 10.14773/cst.2013.12.4.163
45.
MansfeldFHuetFMattosO.New trends in electrochemical impedance spectroscopy (EIS) and electrochemical noise analysis (ENA): proceedings of the international symposium. Electrochem Soc. 2001; 1: 86–87.
46.
TsuchiyaHFujimotoSChiharaOSemiconductive behavior of passive films formed on pure Cr and Fe–Cr alloys in sulfuric acid solution. Electrochim Acta. 2002; 47 (27): 4357–4366. doi: 10.1016/S0013-4686(02)00508-X
47.
HuangJWuXHanE-H.Electrochemical properties and growth mechanism of passive films on alloy 690 in high-temperature alkaline environments. Corros Sci. 2010; 52 (10): 3444–3452. doi: 10.1016/j.corsci.2010.06.016
48.
KimJJYoungYM.Study on the passive film of type 316 stainless steel. Int J Electrochem Sci. 2013; 8 (10): 11847–11859.
49.
Morshed-BehbahaniKNajafisayarPPakshirMAn electrochemical study on the effect of stabilization and sensitization heat treatments on the intergranular corrosion behaviour of AISI 321H austenitic stainless steel. Corros Sci. 2018; 138: 28–41. doi: 10.1016/j.corsci.2018.03.043
50.
LiBZhangW.Electrochemical and corrosion behavior of 2205 duplex stainless steel in simulated concrete pore solution. Int J Electrochem Sci. 2017; 12: 8432–8446. doi: 10.20964/2017.09.43
51.
FengHLiHZhangS. Corrosion Behavior of Super Duplex Stainless Steel S32750 in White Liquor. Int J Electrochem Sci. 2015; 10: 4116–4128.
52.
YaoJDongCManC. The electrochemical behavior and characteristics of passive film on 2205 duplex stainless steel under various hydrogen charging conditions. Corrosion. 2015; 72 (1): 42–50.
53.
LuoHDongCXiaoKCharacterization of passive film on 2205 duplex stainless steel in sodium thiosulphate solution. Appl Surf Sci. 2011; 258 (1): 631–639. doi: 10.1016/j.apsusc.2011.06.077
54.
Fattah-AlhosseiniA.Passivity of AISI 321 stainless steel in 0.5M H2SO4 solution studied by Mott–Schottky analysis in conjunction with the point defect model. Arab J Chem. 2016; 9: S1342–S1348. doi: 10.1016/j.arabjc.2012.02.015
55.
YangL.Techniques for corrosion monitoring. -: Elsevier; 2008. p. 396–397.
56.
McCaffertyE.Validation of corrosion rates measured by the Tafel extrapolation method. Corros Sci. 2005; 47 (12): 3202–3215. doi: 10.1016/j.corsci.2005.05.046
57.
McCaffertyEMcArdleJV.Corrosion inhibition of iron in acid solutions by biological siderophores. J Electrochem Soc. 1995; 142 (5): 1447–1453. doi: 10.1149/1.2048595
58.
McCaffertyE.Electrochemical behavior of iron within crevices in nearly neutral chloride solutions. J Electrochem Soc. 1974; 121 (8): 1007–1013. doi: 10.1149/1.2401968
