Two types of low-transformation-temperature weld metals were devised, one associated with primary austenite solidification, the other primary ferrite solidification. The martensite start temperature of both low-transformation-temperature weld metals was about 125°C. Experimental results showed that low-transformation-temperature weld microstructure associated with primary austenite solidification was martensite with 8.0% retained austenite, whereas that one related to primary ferrite solidification primarily consisted of martensite and δ-ferrite. Accordingly, both welded joints had little distinction between distortion and residual stress, indicating that weld metal associated with primary ferrite solidification played the same function as primary austenite solidification on residual stress reduction. Moreover, the low-transformation-temperature weld metal associated with primary ferrite solidification had higher tensile strength and hardness than that based on primary austenite solidification.
AlghamdiT, LiuS.Low-transformation-temperature (LTT) welding consumables for residual stress management: consumables development and testing qualification. Weld J. 2014; 93:243–252.
2.
OkanoS, MochizukiM.A methodology of appropriate weld procedures for axial compressive residual stress on inner surface in multi-pass girth welded pipe joint. J High Press Inst Jpn. 2010; 48:86–96.
3.
TaiM, MikiC.Fatigue performance under variable amplitude loading of welded joints by introducing compressive residual stress. J Jpn Soc Civ Eng Ser A1. 2015; 71:139–151.
4.
IlmanMN, Kusmono,Muslih MR, . Mitigating distortion and residual stress by static thermal tensioning to improve fatigue crack growth performance of MIG AA5083 welds. Mater Des. 2016; 99:273–283. doi: 10.1016/j.matdes.2016.03.049
5.
ZhaoMS, ChiewSP, LeeCK.Post weld heat treatment for high strength steel welded connections. J Construct Steel Res. 2016; 122:167–177. doi: 10.1016/j.jcsr.2016.03.015
6.
GanJ, SunD, WangZ, The effect of shot peening on fatigue life of Q345D T-welded joint. J Construct Steel Res. 2016; 126:74–82. doi: 10.1016/j.jcsr.2016.07.010
7.
KudryavtsevY, KleimanJ.Residual stress management in welding: measurement, fatigue analysis and improvement treatments. Paton Weld J. 2013; 10:135–141.
8.
JonesW, AlberryP.A model for stress accumulation in steels during welding. Met Technol. 1977; 11:557–566.
9.
SatohK, MatsuiS, MachidaT.Thermal stresses developed in high-strength steels subjected to thermal cycles simulating weld heat-affected zone. Trans Jpn Weld Soc. 1972; 3:135–142.
10.
NitschkepagelT, WohlfahrtH.Residual stress distributions after welding as a consequence of the combined effect of physical, metallurgical and mechanical sources. In: KarlssonL, LindgrenLE, JonssonM, editors. Mechanical effects of welding: IUTAM symposium Lulea/Sweden 1991. Berlin: Springer Verl; 1992. p. 123–134.
11.
OhtaA.Fatigue strength improvement by using newly developed low transformation temperature welding material. Weld World. 1999; 43:38–42.
12.
LixingH, DongpoW, WenxianW, . Ultrasonic peening and low transformation temperature electrodes used for improving the fatigue strength of welded joints. Weld World. 2004; 48:34–39. doi: 10.1007/BF03266425
13.
ThibaultD, BocherP, ThomasM, Residual stress characterization in low transformation temperature 13%Cr–4%Ni stainless steel weld by neutron diffraction and the contour method. Mater Sci Eng A. 2010; 527:6205–6210. doi: 10.1016/j.msea.2010.06.035
14.
ZenitaniS, HayakawaN, YamamotoJ, Development of new low transformation temperature welding consumable to prevent cold cracking in high strength steel welds. Sci Technol Weld Join. 2007; 12:516–522. doi: 10.1179/174329307X213675
15.
RamjaunT, StoneHJ, KarlssonL, Effect of interpass temperature on residual stresses in multipass welds produced using low transformation temperature filler alloy. Sci Technol Weld Join. 2014; 19:44–51. doi: 10.1179/1362171813Y.0000000162
16.
NovotnýL, de AbreuHFG, de MirandaHC, Simulations in multipass welds using low transformation temperature filler material. Sci Technol Weld Join. 2016; 21:680–687. doi: 10.1080/13621718.2016.1177989
17.
KrommA, DixneitJ, KannengiesserT.Residual stress engineering by low transformation temperature alloys—state of the art and recent developments. Weld World. 2014; 58:729–741. doi: 10.1007/s40194-014-0155-6
BishDL, HowardSA.Quantitative phase analysis using the Rietveld method. J Appl Crystallogr. 1988; 21:86–91. doi: 10.1107/S0021889887009415
20.
KimYH, KimDG, SungJH, Influences of Cr/Ni equivalent ratios of filler wires on pitting corrosion and ductility-dip cracking of AISI 316L weld metals. Met Mater Int. 2011; 17:151–155. doi: 10.1007/s12540-011-0221-1
21.
SchaefflerAL.Constitution diagram for stainless-steel weld metal. 2. Schaeffler diagram. Met Prog. 1974; 106:227–227.
22.
BehjatiP, NajafizadehA.Role of chemical driving force in martensitic transformations of high-purity Fe-Cr-Ni alloys. Metall Mater Trans A. 2011; 42:3752–3760. doi: 10.1007/s11661-011-0769-x
23.
Nitschke-PagelT, WohlfahrtH.Residual stresses in welded joints – sources and consequences. Mater Sci Forum. 2002; 404–407:215–226. doi:
10.4028/www.scientific.net/MSF.404-407.215
24.
ElmerJ, OlsonD, MatlockD.Thermal expansion characteristics of stainless steel weld metal. Weld J. 1982; 61:293–301.
25.
MochizukiM, MatsushimaS, ToyodaM, Fundamental study of thermal stress generation during welding heat cycles. Studies on numerical simulation of temperature, microstructure and thermal stress histories during welding, and their application to welded structures. Weld Int. 2005; 19:702–710. doi: 10.1533/wint.2005.3490
26.
RajasekharK, HarendranathCS, RamanR, Microstructural evolution during solidification of austenitic stainless steel weld metals: a color metallographic and electron microprobe analysis study. Mater Charact. 1997; 38:53–65. doi: 10.1016/S1044-5803(97)80024-1
27.
LinYC, ChenPY.Effect of nitrogen content and retained ferrite on the residual stress in austenitic stainless steel weldments. Mater Sci Eng A. 2001; 307:165–171. doi: 10.1016/S0921-5093(00)01821-9
28.
AlghamdiT, LiuS.Low transformation temperature welding consumables for residual stress management: a numerical model for the prediction of phase transformation-induced compressive residual stresses. Weld J.2014; 93:458–471.
29.
QiuH, WangL, ZuoH, Enhanced low-temperature tensile properties of Fe–14Cr–(4∼9)Ni weld metal by retained austenite. Q J Jpn Weld Soc. 2012; 30:171–179. doi: 10.2207/qjjws.30.171
30.
ZhangZ, FarrarRA.Columnar grain development in C–Mn–Ni low-alloy weld metals and the influence of nickel. J Mater Sci. 1995; 30:5581–5588. doi: 10.1007/BF00356690
31.
WangP, LuSP, XiaoNM, Effect of delta ferrite on impact properties of low carbon 13Cr–4Ni martensitic stainless steel. Mater Sci Eng A. 2010; 527:3210–3216. doi: 10.1016/j.msea.2010.01.085
32.
BashuSA, SinghK, RawatMS.Effect of heat treatment on mechanical properties and fracture behaviour of a 12CrMoV steel. Mater Sci Eng A. 1990; 127:7–15. doi: 10.1016/0921-5093(90)90184-5
33.
FengZL, HuoLX, WangWX, Experiment on dressing for improving fatigue strengths of welded joints with low transformation temperature electrode. Trans China Weld Inst. 2006; 27:11–14.
34.
XuLY, WangYF, JingHY, Fatigue strength improvement of stainless steel using weld toes dressing with low transformation temperature welding wire. Sci Technol Weld Join. 2014; 19:664–672. doi: 10.1179/1362171814Y.0000000240
35.
HsiehCC, LinDY, ChenMC, Precipitation and strengthening behavior of massive δ-ferrite in dissimilar stainless steels during massive phase transformation. Mater Sci Eng A. 2008; 477:328–333. doi: 10.1016/j.msea.2007.05.037
