The paper addresses the microstructure and failure characteristics of dissimilar resistance spot welds between austenitic stainless steel and ferritic stainless steel. The fusion zone (FZ) of dissimilar welds exhibited complex microstructure consisting of ferrite, austenite and martensite. The development of this triplex structure in the FZ was explained by analysing the phase transformation path and austenite stability. Results showed that all dissimilar welds failed in partial thickness–partial pull-out failure mode. It was shown that the fraction of the nugget fracture of the weld is reduced by increasing the FZ size improving the mechanical performance of the weld. Peak load and energy absorption of the similar and dissimilar welds were compared and analysed.
CapelliF., BoneschiV. and ViganòP.: ‘Stainless steel: A new structural automotive material, vehicle architectures: Evolution towards improved safety, low-weight, ergonomics, and flexibility’, Paper presented at Florence ATA 2005, 9th International Conference (Florence), May 2005.
4.
KyröläinenA., VilpasM. and HänninenH.: ‘Use of stainless steels in bus coach structure’, J. Mater. Eng. Perform., 2000, 9, 669–677. doi: 10.1361/105994900770345548
5.
SirenM., de WispelaereN., RizzoL., PaultyT., KosmacA., TaulavuoriT., SanchezR., VliegenR., Van HeckeB., SaynevirtaJ. and HanninenH.: ‘Innovative stainless steel applications in transport vehicles, available’, Luxembourg, Publication Office of the European Union, 2011, Research Found for Coal and Steel series, available at http://www.euro-inox.org/pdf/auto/INSAPTRANS_Handbook_EN.pdf (accessed [25 October 2015]).
SchuberthS., SchedinE., FrohlichT. and RatteE.: ‘Next generation vehicle – engineering guidelines for stainless steel in automotive application’, Proc. 6th Stainless Steel Science and Market Conf., Helsinki, Finland, June 2008. Jernkontoret, The Swedish Steel Producers’ Association, Paper G02-1, 637–644.
8.
SnelgroveP.: ‘Stainless steel automotive and transport developments’, Int. Stain. Steel Forum, 2012, 1–5, available at www.worldstainless.org, (accessed [23 October 2015]).
9.
HoshinoK., KanezashiH. and OsakiK.: ‘Effect of electrical resistance on penetration of spot welding in high strength stainless steels’, Trans. ISIJ, 1983, 23, 1085–1090. doi: 10.2355/isijinternational1966.23.1085
10.
NexC. P. and SmithR. A.: ‘Impact performance of model spot-welded stainless steel structures’, 11th Int. Conf. on ‘Experimental Mechanics’, Oxford (UK), 1998. Allison (editor) Balkema, Rotterdam.
11.
PouranvariM. and MarashiS. P. H.: ‘Failure mode transition in AISI 304 resistance spot welds’, Weld. J., 2012, 91, 303s–309s.
12.
JaberH. L., PouranvariM., MarashiS. P. H., Alizadeh-ShM., SalimR. K. and HashimF. A.: ‘Dissimilar spot welding of dual phase steel/ferritic stainless steel: phase transformations’, Sci. Technol. Weld. Join., 2014, 19, 565–571. doi: 10.1179/1362171814Y.0000000226
13.
Alizadeh-ShM., MarashiS. P. H. and PouranvariM.: ‘Microstructure-properties relationships in martensitic stainless steel resistance spot welds’, Sci. Technol. Weld. Join., 2014, 19, 595–602. doi: 10.1179/1362171814Y.0000000230
14.
AleniusM., PohjanneP., SomervuoriM. and HanninenH.: ‘Exploring the mechanical properties of spot welded dissimilar joints for stainless and galvanized steels’, Weld. J., 2006, 85, 305s–313s.
15.
PouranvariM. and MarashiS. P. H.: ‘Similar and dissimilar RSW of low carbon and austenitic stainless steels: Effect of weld microstructure and hardness profile on failure mode’, Mater. Sci. Technol., 2009, 25, 1411–1416. doi: 10.1179/026708309X12459430509292
16.
LiuW., SunC., XuX., ZuoY. and LinJ.: ‘The influences of nugget diameter on the mechanical properties and the failure mode of resistance spot-welded metastable austenitic stainless steel’, Mater. Des., 2012, 33, 292–299. doi: 10.1016/j.matdes.2011.06.071
17.
Alizadeh-ShM., MarashiS. P. H. and PouranvariM.: ‘Resistance spot welding of AISI 430 ferritic stainless steel: Phase transformations and mechanical properties’, Mater. Des., 2014, 56, 258–263. doi: 10.1016/j.matdes.2013.11.022
18.
PouranvariM., Alizadeh-ShM. and MarashiS. P. H.: ‘Welding metallurgy of stainless steels during resistance spot welding, Part I: Fusion zone’, Sci. Technol. Weld. Join., 2015, 20, 502–511. doi: 10.1179/1362171815Y.0000000015
19.
Alizadeh-ShM., PouranvariM. and MarashiS. P. H.: ‘Welding metallurgy of stainless steels during resistance spot welding, Part II: Heat affected zone and mechanical performance’, Sci. Technol. Weld. Join., 2015, 20, 512–521. doi: 10.1179/1362171815Y.0000000010
20.
PouranvariM., MarashiS. P. H. and Alizadeh-ShM.: ‘Welding metallurgy of dissimilar AISI 430/DQSK steels resistance spot welds’, Weld. J., 94, 2015, 203–210.
21.
WeiS. T., LvD., LiuR. D., LinL., XuR. J., GuoJ. Y. and WangK. Q.: ‘Similar and dissimilar resistance spot welding of advanced high strength steels: Welding and heat treatment procedures, structure and mechanical properties’, Sci. Technol. Weld. Join., 2014, 19, 427–435. doi: 10.1179/1362171814Y.0000000211
22.
PouranvariM.: ‘Susceptibility to interfacial failure mode in similar and dissimilar resistance spot welds of DP600 dual phase steel and low carbon steel during cross-tension and tensile-shear loading conditions’, Mater. Sci. Eng. A, 2012, 546, 129–138. doi: 10.1016/j.msea.2012.03.040
23.
PouranvariM., MarashiS. P. H. and MousavizadehS. M.: ‘Failure mode transition and mechanical properties of similar and dissimilar resistance spot welds of DP600 and low carbon steels’, Sci. Technol. Weld. Join., 2010, 15, 625–631. doi: 10.1179/136217110X12813393169534
24.
Recommended practices for test methods for evaluating the resistance spot welding behavior of automotive sheet steel materials. ANSI/AWS/SAE/D89–97. Miami, ML, USA, AWS; 1997.
25.
HoC. Y. and ChuT. K.: ‘Electrical resistivity and thermal conductivity of nine selected AISI stainless steel’, CINDAS Report 45, American Iron and Steel Institute, September 1977.
26.
LiY. B., LinZ. Q., LaiX. M. and ChenG. L.: ‘Electromagnetic phenomena in resistance spot welding and its effects on weld nugget formation’, PIERS Proceedings, Moscow, Russia, August 18–21, 2009, 744–748.
27.
LippoldJ. C. and KoteckiD. J.: ‘Welding metallurgy and weldability of stainless steels’; 2005, New Jersey, John Wiley & Sons.
28.
SelfJ. A., OlsonD. L. and EdwardsG. R.: ‘The stability of austenitic weld metal’, NBS Publ. Cryogenic Prop. Metals, 1987, 181–189.
29.
SchaefflerA. L.: ‘Constitution diagram for stainless steel weld metal’, Metal Prog., 1949, 56, 680–680B.
KakhovskiiN. I., LipodaevV. N. and FadeevaG. V.: ‘The arc welding of stable austenitic corrosion-resisting steels and alloys’, Avtomaticheskaya Svarka, 1980, 33, 55–57.
32.
PotakY. M. and SagalevichE. A.: ‘Structural diagram for stainless steels as applied to cast metal and metal deposited during welding’, Avtomaticheskaya Svarka, 1972, 25, 10–13.
33.
GouldJ. E., KhuranaS. P. and LiT.: ‘Predictions of microstructures when welding automotive advanced high-strength steels’, Weld. J., 2006, 85, 111s–116s.
34.
PouranvariM. and RanjbarnoodehE.: ‘Dependence of the fracture mode on the welding variables in the resistance spot welding of ferrite-martensite DP980 advanced high-strength steel’, Materiali in tehnologije, 2012, 46, 665–671.
35.
PouranvariM.: ‘Failure mode transition in similar and dissimilar resistance spot welds of HSLA and low carbon steels’, Can. Metall. Quart., 2012, 51, 67–74. doi: 10.1179/1879139511Y.0000000020
36.
DuanR., LuoZ., LiY., ZhangY. and LiuZ. M.: ‘Novel postweld heat treatment method for improving mechanical properties of resistance spot weld’, Sci. Technol. Weld. Join., 2015, 20, 100–105. doi: 10.1179/1362171814Y.0000000262
37.
PouranvariM. and MarashiS. P. H.: ‘On the failure of low carbon steel resistance spot welds in quasi-static tensile–shear loading’, Mater. Des., 2010, 31, 3647–3652. doi: 10.1016/j.matdes.2010.02.044
38.
SafanamaD. S., MarashiS. P. H. and PouranvariM.: ‘Similar and dissimilar resistance spot welding of martensitic advanced high strength steel and low carbon steel: metallurgical characteristics and failure mode transition’, Sci. Technol. Weld. Join., 2012, 17, 288–294. doi: 10.1179/1362171812Y.0000000006
