The effect of microstructure and Cu addition in a simulated coarse-grained heat-affected zone (CGHAZ) of a high-strength low-alloy (HSLA) steel subjected to 100 kJ cm−1 heat input welding was studied. It has been observed that the primary microstructure in Cu-free HSLA steels is dominated by bainite, whereas, in Cu-bearing HSLA steels, the predominant microstructure is acicular ferrite. The acicular ferrite nucleated at intragranular complex inclusions consisting of Al and Ti oxides, covered with layer of MnS and CuS. The presence of high intensity of acicular ferrite and hard impingements between acicular ferrite laths or plates has contributed to the fine-grained and interlocked microstructure. The enhanced toughness in CGHAZ of Cu-bearing HSLA steel is attributed to the fine-grained interlocked microstructure of acicular ferrite.
BhadeshiaH. K. D. H.: ‘Bainite in steels’, 3rd edn; 2006, Oxford, UK, Elsevier Ltd.
2.
WanX. L., WangH. H., ChengL. and WuK. M.: ‘The formation mechanisms of interlocked microstructures in low-carbon high-strength steel weld metals’, Mater. Charact., 2012, 67, 41–51. doi: 10.1016/j.matchar.2012.02.007
3.
RicksR. A., HowellP. R. and BarritteG. S.: ‘The nature of acicular ferrite in HSLA steel weld metals’, J. Mater. Sci., 1982, 17, 732–740. doi: 10.1007/BF00540369
4.
ShiM., ZhangP. and ZhuF.: ‘Toughness and microstructure of coarse grain heat affected zone with high heat input welding in Zr-bearing low carbon steel’, ISIJ Int., 2014, 54, 188–192. doi: 10.2355/isijinternational.54.188
5.
ZhangZ. and FarrarR. A.: ‘Role of non-metallic inclusions in formation of acicular ferrite in low alloy weld metals’, Mater. Sci. Technol., 1996, 12, 237–260. doi: 10.1179/mst.1996.12.3.237
6.
ShimJ. H., ByunJ. S., ChoY. W., OhY. J., ShimJ. D. and LeeD. N.: ‘Mn absorption characteristics of Ti2O3 inclusions in low carbon steels’, Scripta Mater., 2001, 44, 49–54. doi: 10.1016/S1359-6462(00)00560-1
7.
ShigesatoG. and SugiyamaM.: ‘Development of in-situ observation technique using scanning ion microscopy and demonstration of Mn depletion effect on intra-granular ferrite transformation in low-alloy steel’, J. Electron Microsc., 2002, 51, 359–367. doi: 10.1093/jmicro/51.6.359
8.
ZhuK. and YangZ.: ‘Effect of Mg addition on the ferrite grain boundaries misorientation in HAZ of low carbon steels’, J. Mater. Sci. Technol., 2011, 27, 252–256. doi: 10.1016/S1005-0302(11)60058-3
9.
GuoA. M., LiS. R., GuoJ., LiP. H., DingQ. F. and WuK. M.: ‘Effect of zirconium addition on the impact toughness of heat affected zone in high strength low alloy pipeline steel’, Mater. Charact., 2008, 59, 134–139. doi: 10.1016/j.matchar.2006.11.028
10.
MadariagaI. and GutiCrrezI.: ‘Nucleation of acicular ferrite enhanced by the precipitation of CuS on MnS particles’, Scripta Mater., 1997, 37, 1185–1192.
11.
LiuZ., KobayashiY., YinF., KuwabaraM. and NagaiK.: ‘Nucleation of acicular ferrite on sulfide inclusion during rapid solidification of low carbon steel’, ISIJ Int., 2007, 47 (12), 1781–1788. doi: 10.2355/isijinternational.47.1781
12.
YuL., WangH. H., HouT. P., WangX. L., WanX. L. and WuK. M.: ‘Characteristic of martensite–austenite constituents in coarse grained heat affected zone of HSLA steel with varying Al contents’, Sci. Technol. Weld. Joi., 2014, 19, (8), 708–714. doi: 10.1179/1362171814Y.0000000246
13.
MabuchiH., UemoriR. and FujiokaM.: ‘The role of Mn depletion in intra-granular ferrite transformation in the heat affected zone of welded joints with large heat input in structural steels’, ISIJ Int., 1996, 36, 1406–1412. doi: 10.2355/isijinternational.36.1406
14.
ZhangS., HattoriN., EnomotoM. and TaruiT.: ‘Ferrite nucleation at ceramic/austenite interfaces’, ISIJ Int., 1996, 36, 1301–1309. doi: 10.2355/isijinternational.36.1301
15.
FuruharaT.: ‘Multiphase crystallography in the nucleation of intragranular ferrite on MnS+V(C,N) complex precipitate in austenite’, ISIJ Int., 2003, 43, 2028–2037. doi: 10.2355/isijinternational.43.2028
16.
LiuZ. and KuwabaraM.: ‘Up-to-date progress of technology of oxide metallurgy and its practice’, Steelmaking, 2007, 23 (3), 7–13. (In Chinese)
17.
ParkK. T., HwangS. W., JiJ. H. and LeeC. H.: ‘Inclusions nucleating intragranular polygonal ferrite and acicular ferrite in low alloyed carbon manganese steel welds’, Met. Mater. Int., 2011, 17, 349–356. doi: 10.1007/s12540-011-0425-4
18.
WanX. L., WuK. M., HuangG. and WeiR.: ‘In situ observations of the formation of fine-grained mixed microstructures of acicular ferrite and bainite in the simulated coarse-grained heat-affected zone’, Steel Res. Int., 2014, 85, 243–250. doi: 10.1002/srin.201200313
19.
WanX. L., WeiR. and WuK. M.: ‘Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone’, Mater. Charact., 2010, 61, 726–731. doi: 10.1016/j.matchar.2010.04.004
20.
MatsudaF., IkeuchiK., OkadaH., HrivnakI. and ParkH. S.: ‘Effect of M–A constituent on fracture behavior of 780 and 980MPa class HSLA steels subjected to weld HAZ thermal cycles’, Trans. JWRI, 1994, 23 (2), 231–237.
