The effects of Cu content on microstructure and impact toughness in the simulated coarse-grained heat-affected zone (CGHAZ) of high-strength low-alloy steels were investigated. It has been observed that the microstructure in the simulated CGHAZ of Cu-free steel is dominated by a small proportion of acicular ferrite and predominantly bainite with martensite–austenite constituent. Whereas, in the 0.45 and 1.01% Cu-containing steels, the acicular ferrite increased significantly due to the effective nucleation on intragranular inclusions with outer layer of MnS and CuS. The formation of acicular ferrite is attributed to superior high heat-affected zone impact toughness in the 0.45% Cu-containing steel. Furthermore, the increasing martensite–austenite constituent and ε-Cu precipitates in the simulated CGHAZ of 1.01% Cu-containing steel caused degradation in impact toughness.
YanW., ShanY. Y. and YangK.: ‘Effect of TiN inclusions on the impact toughness of low-carbon microalloyed steels’, Metall. Mater. Trans. A, 2006, 37, 2147–2158. doi: 10.1007/BF02586135
2.
ShowB. K., VeerababuR., BalamuralikrishnanR. and MalakondaiahG.: ‘Effect of vanadium and titanium modification on the microstructure and mechanical properties of a microalloyed HSLA steel’, Mater. Sci. Eng. A, 2010, 527, 1595–1604. doi: 10.1016/j.msea.2009.10.049
3.
XuG., GanX. L., MaG. J., LuoF. and ZouH.: ‘Effects of Ti and B addition on microstructures and mechanical properties of hot-rolled high-strength Nb-containing steels’, Mater. Des., 2010, 31, 2891–2896. doi: 10.1016/j.matdes.2009.12.032
4.
FunakoshiT., TanakaT., UedaS., IshikawaM., KoshizukaN. and KobayashiK.: ‘Improvement in microstructure and toughness of large heat input weld bond of high strength steel due to addition of rare earth metals and boron’, Trans. ISIJ., 1977, 17, 419–427.
5.
KanazawaS., NakashimaA., OkamotoK. and KnayaK.: ‘Improvement of weld fusion zone toughness by fine TiN’, Trans. ISIJ, 1976, 16, 486–495.
6.
YuL., WangH. H., WangX. L., HuangG., HouT. P. and WuK. M.: ‘Improvement of impact toughness of simulated heat affected zone by addition of aluminium’, Mater. Sci. Technol., 2014, 30, (15), 1951–1958. doi: 10.1179/1743284714Y.0000000602
7.
BonnevieE., FerriereG., IkhlefA., KaplanD. and OrainJ. M.: ‘Morphological aspects of martensite–austenite constituents in intercritical and coarse grain heat affected zones of structural steels’, Mater. Sci. Eng. A, 2004, 385, 352–358. doi: 10.1016/S0921-5093(04)00859-7
8.
ZhangY. Q., ZhangH. Q., LiuW. M. and HouH.: ‘Effects of Nb on microstructure and continuous cooling transformation of coarse grain heat-affected zone in 610 MPa class high-strength low-alloy structural Steels’, Mater. Sci. Eng. A, 2009, 499, 182–186. doi: 10.1016/j.msea.2007.10.118
9.
WidgeryD. J.: ‘The effects of copper in mild steel weld metal’, Met. Constr., 1978, 10, 480–483.
10.
LiS. B., ZhangJ. X. and ZhuB. K.: ‘Effect of copper content on the weld metal toughness of HSLA steels’, Weld. Joi., 2005, 11, 27–30. (In Chinese)
11.
MadariagaI., RomeroJ. L. and GutiérresI.: ‘Upper acicular ferrite formation in a medium-carbon microalloyed steel by isothermal transformation: nucleation enhancement by CuS’, Metall. Mater. Trans. A, 1998, 29A, 1003–1015. doi: 10.1007/s11661-998-1009-x
12.
Díaz-FuentesM., MadariagaI. and GutiérresI.: ‘Acicular ferrite microstructures and mechanical properties in a low carbon wrought steel’, Mater. Sci. Forum, 1998, 284–286, 245–252. doi: 10.4028/www.scientific.net/MSF.284-286.245
13.
LaitinenR.: Improvement of weld HAZ toughness at low heat input by controlling the distribution of M-A constituents, University of Oulu, 2006, Finland.
14.
ShiX., YanW., WangW., ShanY. and YangK.: ‘Novel Cu-bearing high-strength pipeline steels with excellent resistance to hydrogen-induced cracking’, Mater. Des., 2016, 92, 300–305.
15.
WanX. L., WangH. H., ChengL. and WuK. M.: ‘The formation mechanisms of interlocked microstructures in HSLA steel weld metals-2’, Mater. Charact., 2012, 67, 41–51. doi: 10.1016/j.matchar.2012.02.007
16.
WanX. L., WuK. M., NuneK. C., LiY. and ChengL.: ‘In situ observation of acicular ferrite formation and grain refinement in simulated heat affected zone of high strength low alloy steel’, Sci. Technol Weld Joi., 2015, 20, (3), 254–263. doi: 10.1179/1362171815Y.0000000008
17.
GuoA. M., LiS. R., GuoJ., LiP. H., DingQ. F., WuK. M. and HeX. L.: ‘Effect of zirconium addition on the impact toughness of the heat affected zone in a high strength low alloy pipeline steel’, Mater. Charact., 2008, 59, (1), 134–139. doi: 10.1016/j.matchar.2006.11.028
18.
MatsudaF., LiZ., BernazovskyP., IshiharaK. and OkadaH.: ‘An investigation on the behaviour of the M-A constituent in simulated HAZ of HSLA steels’, Weld World, 1991, 29, (9–10), 307–313.
19.
ZhengW., WuZ. H., LiG. Q., ZhangZ. and ZhuC. Y.: ‘Effect of Al content on the characteristics of inclusions in Al-Ti complex deoxidized steel with calcium treatment’, ISIJ Int., 2014, 54, (8), 1755–1764. doi: 10.2355/isijinternational.54.1755
20.
MadariagaI. and GutiérresI.: ‘Nucleation of acicular ferrite enhanced by the precipitation of CuS on MnS particles’, Scripta Mater., 1997, 37, 1185–1192. doi: 10.1016/S1359-6462(97)00229-7
21.
ShiM., ZhangP. and ZhuF.: ‘Toughness and microstructure of coarse grain heat affected zone with high heat input welding in Zr-bearing low carbon steel’, ISIJ Int., 2014, 54, 188–192. doi: 10.2355/isijinternational.54.188
22.
MabuchiH., UemoriR. and FujiokaM.: ‘The role of Mn depletion in intra-granular ferrite transformation in the heat affected zone of welded joints with large heat input in structural steels’, ISIJ Int., 1996, 36, 1406–1412. doi: 10.2355/isijinternational.36.1406
23.
ZhangS., HattoriN., EnomotoM. and TaruiT.: ‘Ferrite nucleation at ceramic/austenite interfaces’, ISIJ Int., 1996, 36, 1301–1309. doi: 10.2355/isijinternational.36.1301
24.
RicksR. A., HowellP. R. and BarritteG. S.: ‘The nature of acicular ferrite in HSLA steel weld metals’, J. Mater. Sci., 1982, 17, 732–740. doi: 10.1007/BF00540369
25.
FuruharaT: ‘Multiphase crystallography in the nucleation of intragranular ferrite on MnS+V(C, N) complex precipitate in austenite’, ISIJ Int., 2003, 43, 2028–2037. doi: 10.2355/isijinternational.43.2028
26.
ShimJ. H., ByunJ. S., ChoY. W., OhY. J., ShimJ. D. and LeeD. N.: ‘Mn absorption characteristics of Ti2O3 inclusions in low carbon steels’, Scripta Mater., 2001, 44, 49–54. doi: 10.1016/S1359-6462(00)00560-1
27.
LiuZ. and KuwabaraM.: ‘Recent progress in oxide metallurgy technology and its application’, Steelmaking, 2007, 23, (3), 7–13. (In Chinese)
28.
LeeJ. L. and PanY. T.: ‘Microstructure and toughness of the simulated heat-affected zone in Ti- and Al-killed steels’, Mater. Sci. Eng. A, 1991, 136, 109–119. doi: 10.1016/0921-5093(91)90446-T
29.
WanX. L., WeiR. and WuK. M.: ‘Effect of acicular ferrite formation on grain refinement in the coarse-grained region of heat-affected zone’, Mater. Charact., 2010, 61, 726–731. doi: 10.1016/j.matchar.2010.04.004
30.
MazancováE. and MazanecK.: ‘Physical metallurgy characteristics of the M/A constituent formation in granular bainite’, J. Mater. Process. Tech., 1997, 64, (1), 287–292. doi: 10.1016/S0924-0136(96)02578-2
31.
MeyerL., HeisterkampF. and MueschenbornW.: ‘Columbium, Titanium, and Vanadium in normalized, thermo-mechanically treated and cold-rolled steels’, Proceedings of Microalloying 75, Washington, DC, 1975, 153–167.
SoissonF., BarbuA. and MartinG.: ‘Monte Carlo simulations of copper precipitation in dilute iron-copper alloys during thermal ageing and under electron irradiation’, Acta Mater., 1996, 44, (9), 3789–3800. doi: 10.1016/1359-6454(95)00447-5
