In this study, the impact property of 3D printed 15-5 PH stainless steel was investigated at low (77 K), room (298 K), and high temperatures (723 K) using integrated experimental and modelling studies. The finite element model was based on the Johnson-Cook phenomenological material model and fracture parameters. The experimentally measured impact energies are 0.01, 6.78 ± 4.07, and 50.84 ± 3.39 J cm−2, at the low, room, and high temperatures, respectively. The experimental and modelling predicted impact energies are in good agreement. The microstructures show that the steel exhibits a brittle behaviour at low and room temperatures as indicated by a transgranular fracture, but changes to a more ductile behaviour at high temperatures as illustrated by microvoid coalescence induced facture morphology.
OkumotoYTakedaYManoMDesign of Ship Hull Struct, Springer-Verlag Berlin Heidelberg, Dordrecht, Germany, 2009.
2.
ZhangYLinminW, XingyeG., Additive manufacturing of metallic materials: a review. J Mater Eng Perform. 2018; 27(1):1–13.
3.
LewandowskiJJSeifiM.Metal additive manufacturing: a review of mechanical properties. Annu Rev Mater Res. 2016; 46(1):151–186.
4.
PitrmucZ.Influence of process parameters and part orientation on mechanical properties for DMLS manufactured stainless steel AISI 316L. Conferences of Student Creative Activity, STC; 2017:9.
5.
HendricksonJW.Use of direct metal laser sintering for tooling in high volume Production. All Graduate Plan B and other Reports; 2015:724.
6.
Montero SistiagaMNardoneSHautfenneCEffect of heat treatment of 316 l stainless steel produced by selective laser melting (slm). Proceedings of the 27th Annual International Solid Freeform Fabrication Symposium; 2016:558–565.
HernyELoursPAndrieuEEvolution of microstructure and impact-strength energy in thermally and thermomechanically aged 15-5 PH. Proc Inst Mech Eng, Part L: J Mater: Design Appl. 2008; 222(4):299–304.
9.
AminiMRSimonJNemat-NasserS.Numerical modeling of effect of polyurea on response of steel plates to impulsive loads in direct pressure-pulse experiments. Mech Mater. 2010; 42(6):615–627.
10.
BarauskasRAbraitienėA.Computational analysis of impact of a bullet against the multilayer fabrics in LS-DYNA. Int J Impact Eng. 2007; 34(7):1286–1305.
11.
ASTM E23-16b, standard test Methods for notched Bar impact testing of Metallic materials. ASTM International, West Conshohocken, PA; 2016.
12.
SagarS Zhang Y, Wu L, et al. Room-temperature Charpy impact property of 3D-printed 15-5 stainless steel. J Mater Eng Perform. 2018; 27(1):52–56.
13.
Ls-Dyna, LS-DYNA User Manual, LST, an Ansys company; Livermore, CA, USA, 2011.
14.
JohnsonGRCookWH.A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. Proceedings of the 7th International Symposium on ballistics; 1983.
15.
GravesWTLiuDPalazottoAN.Topology Optimization of a Penetrating Warhead. 57th AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference; 2016:1509.
JohnsonGRCookWH.Fracture characteristics of three metals subjected to various strains, strain rates, temperatures and pressures. Eng Fract Mech. 1985; 21(1):31–48.
18.
GrossAJ. Towards the predictive modeling of ductile failure, PhD thesis, The University of Texas at Austin, 2015.
19.
CoffyK.Microstructure and chemistry evaluation of direct metal laser sintered 15-5 PH stainless steel [M.S. thesis]. University of Central Florida; 2014.
20.
CouturierLDe GeuserFDescoinsMEvolution of the microstructure of a 15-5PH martensitic stainless steel during precipitation hardening heat treatment. Mater Des. 2016; 107:416–425.
21.
HertzbergRWVinciRPHertzbergJL.Deformation and fracture mechanics of engineering materials, 5th ed. Hoboken, New Jersey, USA: Wiley; 2012.
22.
WangZXieMLiYPremature failure of an additively manufactured material. NPG Asia Mater. 2020; 12(1):30.
SarkarSDubeySNathAK.Effect of heat treatment on impact toughness of selective laser melted stainless steel parts, June 18–22, 2018, College Station, Texas, USA, Paper No: MSEC2018-6418, V001T01A005, ASME 2018 13th International Manufacturing Science and Engineering Conference, 2018.
