The aim of this study was to investigate and fabricate a Ti64-bagasse ash (BA) composite using the spark plasma sintering (SPS) method. Accordingly, the samples were fabricated under partial densification. XRD analysis, optical and electron microscopy (SEM), hardness measurement, and bending test were used to study the phases formed, the morphology of powders, microstructure, and mechanical properties of the samples, respectively. The results showed that increasing the volume percentage of bagasse ash affected the mechanical properties of the samples in addition to the microstructure. It was also observed that in the samples containing 5 vol.% bagasse ash, in addition to a significant decrease in the value of elastic modulus, the sample fabricated contained pores with a wall composed of ceramic and metal.
XuQ, JiT, GaoSJ, . Characteristics and applications of sugar cane bagasse Ash waste in cementitious materials. Materials (Basel). 2018;12(1):1–19.
2.
MohammadiF, AbdoliMA, AmidpourM, . Environmental-Economic evaluation of sugar cane bagasse gasification power plants versus combined-cycle Gas power plants. Glob J Environ Sci Manag. 2020;6(1):73–84.
3.
PayáJ, MonzóJ, BorracheroMV, . Bagasse ash. 2018
4.
LohYR, SujanD, RahmanME, . Review sugarcane bagasse - The future composite material: A literature review. Resour Conserv Recycl. 2013;75:14–22.
5.
SalesA, LimaSA.Use of Brazilian sugarcane bagasse Ash in concrete as sand replacement. Waste Manag. 2010;30(6):1114–1122.
6.
WarlimontH. Titanium and Titanium alloys. 2018
7.
SankaranKK, MishraRS. Titanium alloys. 2017
8.
QuanY, ZhangF, ReblH, . Ti6Al4V foams fabricated by spark plasma sintering with post-heat treatment. Mater Sci Eng A. 2013;565:118–125.
9.
MirzaaghaeiM, QodsF, ArabiH, . Investigation of mechanical properties and microstructure of Ti-15% Mo alloy produced by mechanical alloying and sintering with SPS (MA-SPS). Powder Metall. 2022.
10.
LiY, YangC, ZhaoH, . New developments of Ti-based alloys for biomedical applications. Materials (Basel). 2014;7(3):1709–1800.
11.
DunandDC.Processing of titanium foams. Adv Eng Mater. 2004;6(6):369–376.
12.
SaravananP, GopalanR, SivaprahasamD, . Effect of sintering temperature on the structure and magnetic properties of SmCo5/Fe nanocomposite magnets prepared by spark plasma sintering. Intermetallics. 2013;42:199–204.
13.
TrusovGV, TarasovAB, MoskovskikhDO, . High porous cellular materials by spray solution combustion synthesis and spark plasma sintering. J. Alloys Compd. 2019;779:557–565.
14.
GarbiecD, SiwakP, MrózA.Effect of compaction pressure and heating rate on microstructure and mechanical properties of spark plasma sintered Ti6Al4V alloy. Arch Civ Mech Eng. 2016;16(4):702–707.
15.
DudinaDV, BokhonovBB, OlevskyEA.Fabrication of porous materials by spark plasma sintering: a review. Materials (Basel). 2019;12(3.
PohlerOEM.Unalloyed titanium for implants in bone surgery. Injury. 2000;31:D7–D13.
18.
MangiSA, JamaluddinN, Wan IbrahimMH, . Utilization of sugarcane bagasse Ash in concrete as partial replacement of cement. IOP Conf Ser Mater Sci Eng. 2017;271(1).
19.
RaufN, DamayantiMC, PratamaSWI.The influence of sugarcane bagasse Ash as Fly Ash on cement quality. AIP Conf Proc. 2017;1801(January):1–4.
20.
JanbualaS, EambuaM, SatayavibulA, . Effect of bagasse and bagasse Ash levels on properties of pottery products. Heliyon. 2018;4(9):e00814.
21.
ArulmaniL, KumarSS.Experimental investigation of aluminium 7075- bagasse Ash-graphite composites. Int J Mater Sci. 2016;11(1):27–31.
22.
KambleA, KulkarniSG.Microstructural examination of bagasse Ash reinforced waste aluminium alloy matrix composite. AIP Conf Proc. 2019;2105(May):1–8.
23.
SinghD, KumarM, KumarN, . Development and characterization of Al/Bagasse ash green metal matrix composite- A review. Int J Adv Res Sci Eng.2017;6(2):624–632.
24.
KalantariSM, ArabiH, MirdamadiS, . Biocompatibility and compressive properties of Ti-6Al-4 V scaffolds having Mg element. J Mech Behav Biomed Mater. 2015;48:183–191.
25.
Mahboubi SoufianiA, EnayatiMH, KarimzadehF.Fabrication and characterization of nanostructured Ti6Al4V powder from machining scraps. Adv Powder Technol. 2010;21(3):336–340.
26.
ASTM F1580-01, 2001. Standard specification for titanium and titanium-6 aluminum-4 vanadium alloy powders for coatings of surgical implant.
27.
AskelandDR, FulayPP, WrightWJ. (2011). The science and engineering of materials.
28.
InternationalA.Standard test method for flexural strength of advanced ceramics at ambient. Order A J. Theory Ordered Sets Its Appl. 1996;94(Reapproved):1–15.
29.
HirschPB.Elements of X-ray diffraction. Phys Bull. 1957;8(7):237–238.
30.
JiaoY, HuangLJ, DuanTB, . Controllable Two-scale network architecture and enhanced mechanical properties of (Ti5Si3+TiBw)/Ti6Al4V composites. Sci Rep. 2016;6(August):2–11.
LütjeringG.Influence of processing on microstructure and mechanical properties of (α + β) titanium alloys. Mater Sci Eng A. 1998;243(1–2):32–45.
33.
LaptevA, VyalO, BramM, . Green strength of powder compacts provided production of highly porous titanium parts. Powder Metall. 2005;48(4):358–364.
34.
ZhangK, FanY, DunneN, . Effect of microporosity on scaffolds for bone tissue engineering. Regen Biomater. 2018;5(2):115–124.
35.
GüdenM, CelikE, HizalA, . Effects of compaction pressure and particle shape on the porosity and compression mechanical properties of sintered Ti6Al4V powder compacts for hard tissue implantation. J Biomed Mater Res B Appl Biomater. 2008;85(2):547–555.
