Experimental Study on Intermediate Crack Debonding in FRP-Strengthened RC Flexural Members

Abstract

A commonly observed failure mode of reinforced concrete (RC) flexural members strengthened with a fibre reinforced polymer (FRP) plate bonded to their tension face involves debonding that initiates at a major flexural or flexural shear crack and propagates towards a plate end, which has often been referred to as intermediate crack (IC) debonding. This paper first presents the results of IC debonding tests conducted on eighteen cantilever slabs in which IC debonding initiated at or near the fixed end, and four simply-supported slabs in three-point bending where IC debonding initiated at the load position. A number of factors are covered by these tests, including the type of FRP material, the width of FRP strip, the length of FRP strip, the slab width, the concrete strength, the longitudinal steel ratio, the concrete cover, and pre-cracking of concrete. The test results are next used to assess the accuracy of four available strength models that can be used to design against IC debonding. Of these four models, Teng et al's (2003) model is shown to provide safe predictions of the test results in most cases but can lead to overly conservative results; the scatter of the predictions is also large. The other three models from recent design guidelines (JSCE, 2001, fib 2001, ACI 440 2002) are not sufficiently safe for use in design. This assessment clearly illustrates the need for much further research to develop a more accurate IC debonding strength model.

Keywords

debonding reinforced concrete slabs FRP composites strengthening bond interfaces

Get full access to this article

View all access options for this article.

References

ACI 440.2R-02. (2002). Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, ACI Committee 440.

ASTM D3039/D3039M-95a (1995). Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, American Society for Testing and Materials (ASTM), Philadelphia, USA.

BS 1881 (1983). Testing Concrete–Part 116: Method for Determination of Compressive Strength of Concrete Cubes; Part 117: Method for Determination of Tensile Splitting Strength; and Part 121: Method for Determination of Static Modulus of Elasticity in Compression, British Standards Institute, London.

BS 8110 (1997). Structural Use of Concrete–Part 1: Code of Practice for Design and Construction, British Standards Institute, London.

Chen

J. F.

and Teng

J. G.

(2001). “Anchorage strength models for FRP and steel plates bonded to concrete”, Journal of Structural Engineering, ASCE, Vol. 127, No. 7, pp. 784–791.

fib (2001). Externally Bonded FRP Reinforcement for RC Structures, Bulletin 14, pp. 51–58.

JSCE. (2001). Recommendations for Upgrading of Concrete Structures with Use of Continuous Fiber Sheets, Concrete Engineering Series 41, Japan Society of Civil Engineers, pp. 31–34.

Lam

and Teng

J. G.

(2001). “Strength of cantilever RC slabs bonded with GFRP strips”, Journal of Composites for Construction, ASCE, Vol. 5, No. 4, pp. 221–227.

Leung

C. K. Y.

(2001). “Delamination failure in concrete beams retrofitted with a bonded plate”, Journal of Materials in Civil Engineering, ASCE, Vol. 13, No. 2, pp. 106–113.

10.

Mohamed Ali

M. S.

Oehlers

D. J.

and Bradford

M. A.

(2001). “Shear peeling of steel plates bonded to the tension faces of RC beams”, Journal of Structural Engineering, ASCE, Vol. 127, No.12, pp. 1453–1460.

11.

Mohamed Ali

M. S.

Oehlers

D. J.

and Bradford

M. A.

(2002). “Interaction between flexure and shear on the debonding of RC beams retrofitted with compression face plates”, Advances in Structural Engineering, Vol.5, No. 4, pp. 223–230.

12.

Niu

and Wu

(2001). “Peeling-off criterion for FRP-strengthened R/C flexural members”, Proceedings of International Conference on FRP Composites in Civil Engineering, Hong Kong, Vol. 1, pp. 571–578.

13.

Oehler

D. J.

Park

S. M.

and Mohamed Ali

M. S.

(2003). “A structural engineering approach to adhesive bonding longitudinal plates to RC beams and slabs”, Composites: Part A, Vol. 34, No. 12, pp. 887–897.

14.

Sebastian

W. M.

(2001). “Significance of midspan debonding failure in FRP-plated concrete beams”, Journal of Structural Engineering, ASCE, Vol. 127, No. 7, pp. 792–798.

15.

Seracino

(2001). “Axial intermediate crack debonding of plates glued to concrete surfaces”, Proceedings of International Conference on FRP Composites in Civil Engineering, Hong Kong, Vol. 1, pp. 365–372.

16.

Smith

S. T.

and Teng

J. G.

(2002a). “FRP-strengthened RC beams. I: Review of debonding strength models”, Engineering Structures, Vol. 24, No. 4, pp. 385–395.

17.

Smith

S. T.

and Teng

J. G.

(2002b). “FRP-strengthened RC beams. II: Assessment of debonding strength models”, Engineering Structures, Vol. 24, No. 4, pp. 397–417.

18.

Smith

S. T.

and Teng

J. G.

(2003). “Shear-bending interaction in debonding failures of FRP-plated RC beams”, Advances in Structural Engineering, Vol. 6, No. 3, pp. 183–199.

19.

Teng

J. G.

Chen

J. F.

Smith

S. T.

and Lam

(2002). FRP Strengthened RC Structures. John Wiley & Sons, Ltd., England.

20.

Teng

J. G.

Cao

S. Y.

and Lam

(2001). “Behaviour of RC cantilever slabs bonded with GFRP strips”, Construction and Building Materials, Vol. 15, No. 7, pp. 339–349.

21.

Teng

J. G.

Lam

Chan

and Wang

(2000). “Retrofitting of deficient RC cantilever slabs using GFRP strips”, Journal of Composites for Construction, ASCE, Vol. 4, No. 2, pp. 75–84.

22.

Teng

J. G.

Smith

S. T.

Yao

and Chen

J. F.

(2003). “Intermediate crack-induced debonding in beams and slabs”, Construction and Building Materials, Vol. 17, Nos. 6–7, pp. 447–462.

23.

Wong

S. Y.

and Vecchio

F. J.

(2003). “Towards modeling of reinforced concrete members with externally bonded fiber-reinforced polymer composites”, ACI Structural Journal, Vol. 100, No. 1, pp. 47–55.

24.

Z. S.

and Yin

(2003). “Fracture behaviors of FRP-strengthened concrete structures”, Engineering Fracture Mechanics, Vol. 70, pp. 1339–1355.

25.

Yao

(2005). “Debonding failures in RC beams and slabs strengthened with FRP plates”, PhD Thesis, The Hong Kong Polytechnic University.