Sage Journals: Discover world-class research

Abstract

This paper presents finite element analysis (FEA) of twenty fabricated square and triangular section (FSTS) stub columns utilizing very high strength (VHS) circular steel tubes with a nominal yield stress of 1,350 MPa. The VHS tubes are placed at each corner of the section and welded to Grade 350 steel plates. Two different nominal diameter-to-thickness ratios of 15.9 and 23.8 were chosen for the VHS tubes. Five different nominal width-to-thickness ratios ranging from 40 to 133 were chosen for the steel plates. Three different lengths of 500, 1000 and 1200mm were chosen for the specimens. The geometric imperfection and softening of heat – affected zone (HAZ) in the VHS tubes were included in the FEA along with material non-linearity and geometric non-linearity. The FEA results were compared with the experimental results and two analytical approaches proposed by the authors. Good agreement was found between the FEA, experimental and analytical results.

Keywords

finite element analysis stub columns fabricated sections high strength steel circular tubes geometric imperfection heat–affected zone non-linearity

Get full access to this article

View all access options for this article.

References

Aoki

and Ji

(2000). “Experimental study on bucking strength of tri-tube steel members”, in Camotim

Dubina

and Rondal

(eds) Proceeding of the 3^th International Conference on Coupled Instabilities in Metal Structures, Lisbon, Portugal, Sept., pp. 283–290.

G+D Computing. (2002). Using STRAD7-Introduction to the Strand7 Finite Element Analysis System, 2nd ed., Sydney, NSW, Australia.

Jiao

and Zhao

X. L.

(2001). “Material ductility of very high strength (VHS) circular steel tubes in tension”, Thin-Walled Structures, Vol. 39, No. 11, pp. 887–906.

Jiao

and Zhao

X. L.

(2002a). “Imperfection, residual stress and yield slenderness limit of very high strength (VHS) circular steel tubes”, Journal of Constructional Steel Research. Vol. 59, No. 2, pp. 233–249.

Jiao

and Zhao

X. L.

(2002b). “Strengthening tests of butt-welded very high strength (VHS) circular steel tubes”, in IABSE Symposium (The International Association for Bridge and Structural Engineering), 11–13 September, Melbourne, Australia.

Jiao

and Zhao

X.L.

(2004a). “Section slenderness limits of very high strength (VHS) circular steel tubes in bending”, Thin-Walled Structures, Vol. 42, No. 9, pp. 1257–1271.

Jiao

and Zhao

X. L.

(2004b). “Tension capacity of very high strength (VHS) circular steel tubes after welding”, Advances in Structural Engineering – An International Journal, Vol. 7, No. 4, pp. 85–96.

Jiao

and Zhao

X. L.

(2004c). “CFRP strengthened butt-welded very high strength (VHS) circular steel tubes”, Thin-Walled Structures, Vol. 42, No. 7, pp. 963–978.

Ling

T. W.

Zhao

X. L.

and Al-Mahaidi

(2002). “Test and design of longitudinal fillet weld in very high strength (VHS) steel circular tubes”, In Advances in Steel Structures

10.

Chan

S. L.

Teng

J. G.

and Chung

K. F.

(eds.), Elsevier, Oxford pp. 245–252.

11.

SAA. (1991). Methods for Tensile Testing Metals, Australian Standard AS 1391, Standards Australia, Sydney.

12.

SAA. (1996). Cold-Formed Steel Structures, Australian/New Zealand Standard AS/NZS4600. Standards Australia, Sydney.

13.

SAA. (1998). Steel structures, Australian Standard AS 4100, Standards Australia, Sydney.

14.

Zhao

X. L.

(2000). “Section capacity of very high strength (VHS) circular tubes under compression”, Thin-Walled Structures, Vol. 37, No. 3, pp. 223–240.

15.

Zaho

X. L.

Binh

D. V.

Al-Mahaidi

and Tao

(2004d). “Stub column tests of fabricated square and triangular sections utilizing very high strength (VHS) circular steel tubes”, Journal of Constructional Steel Research, Elsevier, Vol. 60, No. 11, pp. 1637–1661.

Finite Element Analysis (FEA) of Fabricated Square and Triangular Section Stub Columns Utilizing Very High Strength Steel Tubes

Abstract

Keywords

Get full access to this article

References