Effect of friction force between piston rings and liner: A parametric study of speed,load,temperature,piston-ring curvature,and high-temperature,high-shear viscosity
Restricted accessResearch articleFirst published online May, 2010
Effect of friction force between piston rings and liner: A parametric study of speed,load,temperature,piston-ring curvature,and high-temperature,high-shear viscosity
Efficient engine operation is combined with effective lubrication in the ring/cylinder interface. On the one hand, there should be enough lubricant on the surfaces and, on the other hand, the lubricant contribution to combustion and, thus, to hydrocarbons and particulate emissions should be minimized. These requirements present a challenge to formulate new additives that would enable the lubricant to operate in the demanding circumstances inside the internal combustion engine and at the same time contribute to an environmentally friendly operation. This study is focused on parametric friction force measurements, their appearance close to the dead centres of the stroke, and how load, speed, and temperature affect the friction maxima. An approach is also attempted to the role of high-temperature, high-shear viscosity for a group of CASTROL lubricants. Piston rings with different curvatures were also tested, and friction power losses for each testing case are presented.
DellisP.Aspects of lubrication in piston cylinder assemblies PhD Thesis, Mechanical Engineering Department, Imperial College London, University of London, April 2005.
2.
WakuriY.SoejimaM.EjimaY.HamatakeT.KitaharaT. ‘Studies on friction characteristics of reciprocating engines’ (1995): SAE paper 952471
3.
ArcoumanisC.OstovarP.MortierR. ‘Mixed lubrication modelling of Newtonian and shear thinning liquids in a piston-ring configuration’ (1997): SAE paper 972924
4.
RohdeS. M.WhitakerK. W.McAllisterG. T. ‘A mixed friction model for dynamically loaded contacts with application to piston ring lubrication’ (1980)
5.
PatirN.ChengH. S.‘An average flow model for determining effects of three dimensional roughness on partial hydrodynamic lubrication’Trans. ASME, J. Lubric. Technol.100 (1978): 12–17
6.
GreenwoodJ. A.TrippJ. H.‘The contact of two nominally flat rough surfaces’Proc. Instn Mech. Engrs185 (1971): 625–633
7.
DowsonD.EconomouP. N.RuddyB. L.StrachanP. J.BakerA. J. S. ‘Piston ring lubrication-part II, theoretical analysis of a single ring and a complete ring pack’ (1979)
8.
BolanderN. W.SteenwykB. D.SadeghiF.GerberG. R.‘Lubrication regime transitions at the piston ring-cylinder liner interface’Proc. IMechE, Part J: J. Engineering Tribology219 (1) (2005): 19-31 DOI: 10.1243/135065005X9664
9.
YangQ.KeithT. G.‘An elastohydrodynamic cavitation algorithm for piston ring lubrication’Tribol. Trans.381 (1995): 97–107
10.
YangQ.KeithT. G.‘Two-dimensional piston ring lubrication. Part 1: Rigid ring and liner solution’STLE Tribol. Trans.39 (1996): 757–768
11.
YangQ.KeithT. G.‘Two-dimensional piston ring lubrication. Part 2: Elastic ring consideration’STLE Tribol. Trans.39 (1996): 870–880
12.
AkalinO.NewazG. M.‘Piston ring-cylinder bore friction modelling in mixed lubrication regime. Part II: Correlation with test bench data’Trans. ASME, J. Tribol.123 (2001): 211–218
13.
SawickiJ.YuB.‘Analytical solution of piston ring lubrication using mass conserving cavitation algorithm’STLE Tribol. Trans.43 (2000): 587–594
14.
JengY.‘Theoretical analysis of piston-ring lubrication. Part 1: Fully flooded lubrication’STLE Tribol. Trans.35 (1992): 696–706
15.
ChoS.-W.ChoiS.-M.BaeC.-S.‘Frictional modes of barrel shaped piston rings under flooded lubrication’Tribol. Int.33 (2000): 545–551
16.
ArcoumanisC.DuszynskiM.FloraH.OstovarP. ‘Development of a piston-ring lubrication test-rig and investigation of boundary conditions for modelling lubricant film purposes’ (1995): SAE 952468
17.
ArcoumanisC.OstovarP. ‘An approach to determining non-linear lubricant viscoelastic properties’ (1997): SAE paper 972857
18.
OstovarP.Fluid aspects of piston ring lubrication (Mechanical Engineering Department, Imperial College of Science, Technology and Medicine 1996) PhD Thesis
19.
PykeE. A.Investigation of piston ring lubrication using laser induced fluorescence (Mechanical Engineering Department, Imperial College of Science, Technology and Medicine 2000) PhD Thesis
20.
PriestM.DowsonD.TaylorC. M.‘Theoretical modelling of cavitation in piston-ring lubrication’Proc. IMechE, Part C: J. Mechanical Engineering Science 214 C3 (2000): 435-447 DOI: 10.1243/0954406001523092
21.
DellisP.ArcoumanisC.‘Cavitation development in the lubricant film of a reciprocating piston-ring assembly’Proc. IMechE, Part J: J. Engineering Tribology218 (2004): 157-171 DOI: 10.1243/1350650041323340
22.
SandaS.SomeyaT.‘The effect of surface roughness on lubrication between a piston-ring and a cylinder liner’. In Proceedings of the Institution of Mechanical Engi-neers, International Conference: Tribology — Friction, Lubrication and Wear: Fifty Years On, Queen Elizabeth II Conference Centre, London, 1–3 July 1987, vol. 1, pp. 135–143.
23.
TianT.WongV. W.HeywoodJ. B. ‘A piston-ring pack film thickness and friction model for multigrade oil and rough surfaces’ (1996): SAE paper 962032
24.
StanleyR.TarazaD.HeneinN.BryzikW. ‘A simplified friction model of the piston ring assembly’ (1999): SAE paper 1999-01-0974
25.
TingL. ‘Development of a reciprocating test rig for tribological studies of piston moving components - part II: measurements of piston ring friction coefficients and rig test confirmation’ (1993): SAE paper 930686
