The effects of Nb and homogenization heat treatment on the adhesive wear resistance of AISI 430 ferritic stainless steels containing 18 wt% Cr were investigated. The samples were cast as having additionally 0.5, 1.0, 1.5, and 3 wt% Nb. The samples were hot forged in the form of bars having 20 mm in diameters, and the samples were homogenized. The dry sliding wear tests were performed against AISI 1050 steel in a block-on-ring apparatus under the loads of 40, 60, and 80 N, respectively. The relations between wear rate, sliding distance, surface hardness, notch toughness, grain boundary energies, and friction coefficient were detected, and these relations were searched through metallographic investigations. Finally, it was seen that homogenization heat treatment reduced the total wear rate. The least wear rate was obtained from the homogenized sample having 0.5 wt% Nb in which niobium demonstrated a tendency to stabilize the cubic MX-type precipitates. A compatible relation between surface hardness, notch toughness, grain boundary energies, friction coefficient, and total wear rate was detected for homogenized samples.
UnterwiserP. M.BoyerH. E.KubbsJ. J.Heat treater's guide: standard practices and procedures for steel (Metals Park, OH: ASM1993): p. 418
2.
VoortG. F. V.JamesH. M.MillsK.DavisJ. R.DestafaniJ. D.DieterichD. A.CrankovicG. M.FrisselM. J.ASM handbook: metallography and microstructures (Metals Park, OH: ASM International1992): p. 284k
YaekinaA.SouzaV. M.TaverasS. S. M.SouzaJ. A.de AbreuH. F. G.‘Influence of heat treatments on the intergranular corrosion resistance of the AISI 347 cast and weld metal for high temperature services’J. Mater. Process. Technol.199 (2008): 391–395
5.
AksoyM.KaramişB.EvinE.‘An evaluation of the wear behavior of a dual-phase low-carbon steel’Wear193 (1996): 248–252
KnutsenR. D.langC. I.BassonJ. A.‘Discontinious cellular precipitation in a Cr-Mn-N steel with niobium and vanadium addition’Acta Mater.52 (2004): 2407–2417
8.
KuzucuV.AksoyM.KorkutM. H.YildirimM. M.‘The effect of niobium on the microstructure of ferritic stainless steel’Mater. Sci. Eng. A230 (1997): 75–80
9.
AksoyM.KuzucuV.KorkutM. H.YildirimM. M.‘The effect of niobium and homogenization on the wear resistance and some mechanical properties of ferritic stainless steel containing 17-18 wt% chromium’Mater. Process. Technol.91 (1999): 172–177
10.
HutchigsI. M.Tribologie, friction and wear of engineering materials (London, Melbourne, Auckland: Edward Arnold1992)
YilmazS. O.‘Wear behavior of TiB2 inoculated 20Cr-3Mo-4C high chromium white cast irons’J. Mater. Sci.42 (2007): 6769–6778
13.
KambakasK.TsakiropoulosP.‘Solidification of high-Cr white cast iron-WC particle reinforced composites’Mater. Sci. Eng. A 413-414 (2005): 538–544
14.
AllenA. J.BourkeM. A. M.DaweS.HutchingM. T.WithersP. J.‘The analysis of internal strains measured by neutron diffraction in Al/SiC metal matrix composites’Acta Metall. Mater.40 (1992): 2361
15.
LevyA.PapazianJ. M.‘Elastoplastic finite element analysis of short-fiber-reinforced SiC/Al composites: Effects of thermal treatment’Acta Metall. Mater.39 (1991): 2255–2266
16.
P. J. Withers, T. Lorentzen, O. B. Pedersen, N. Hansen Ed., D. Juuljensen Ed., T. Leffers Ed., (1991)
17.
MailanderR.DiesK.‘Contribution to the study of wear phenomena’Arch. Eisenhüttenwes16 (1943): 385–395
18.
ClarkW. T.PritchardC.MidgleyJ. W.‘Mild wear of unlubricated hard steels in air and carbon dioxide’Proc. Instn Mech. Engrs182 (1967): 99–121
19.
PovirkG. L.NeedlemanA.NuttS. R.‘An analysis of the effect of residual stresses on deformation and damage mechanisms in Al-SiC composites’Mater. Sci. Eng. A132 (1991): 31
20.
FifingM.‘Wear oxidation - a new component of Wear’Trans. Am. Soc. Steel Treat18 (1930): 1026–1034
21.
QuinnT. F. J.SullivanJ. L.RowsonD. M.‘Origins and development of oxidantial wear at low ambient temperatures’Wear94 (1984): 175–191
22.
PetersonM. B.IvesL. K.BhansaliK. J.MerchantF. I. D.BhansaliK. J.Metal transfer and gailing in metallic systems (Warrendale, IA: TMS1987): 1–26
23.
LudemaK. C.‘A review of scuffing and running-in of lubricated surfaces, with asperities and oxides in perspective’Wear100 (1984): 315–331
24.
KragelskiiI. V.Friction and wear (London: Butterworth and Co.1965): 88–94
