EHL Film Thickness Computations at Low Speeds: Risk of Artificial Trends as a Result of Poor Accuracy and Implications for Mixed Lubrication Modelling

Abstract

When numerical and experimental results are compared to validate elasto-hydrodynamic lubrication (EHL) models, it is of utmost importance that grid-converged results are used. In particular at low speeds and high loads, solutions obtained using grids that are not sufficiently dense will exhibit an artificial trend that does not represent the behaviour of the continuous modelling equations. As it coincides with a trend observed in experiments this may lead to the erroneous conclusion that the theoretical model on which the numerical simulations are based is accurate. This risk is illustrated in detail. It is further shown that EHL models based on the Reynolds equation in a steady state circular contact predicts a positive film thickness as long as the grid used in the calculations is sufficiently dense. This has significant implications for the validity of results obtained using mixed lubrication models based on a Reynolds model and a film thickness threshold.

Keywords

elasto-hydrodynamic lubrication (EHL)lubrication models film thickness

Get full access to this article

View all access options for this article.

References

Gohar

Cameron

Optical measurements of oil film thickness under elastohydrodynamic lubrication

Nature, 1963, 200, 458–459.

Cameron

Gohar

Theoretical and experimental studies in lubricated point contact

Proc. Roy. Soc. Land., A, 1966, 291, 520–536.

Cann

P. M.

Spikes

H. A.

Hutchinson

The development of a spacer layer imaging method for mapping elastohydrodynamic contacts

STLE Tribol. Trans., 1996, 36, 915–921.

Lord

Jolkin

Larsson

Marklund

A hybrid film thickness evaluation scheme based on multi-channel interferometry and contact mechanics

ASME J. Tribal, 2000, 122, 16–22.

Kaneta

Effects of surface roughness in elastohydrodynamic lubrication

JSME III, 1992, 35, 535–546.

Glovnea

Spikes

H. A.

Elastohydrodynamic film formation at the start up of the motion

Proc. Instn Mech. Engrs, Part J: J. Engineering Tribology, 2001, 215, 125–138.

Lubrecht

A. A.

ten Napel

W. E.

Bosnia

Multigrid, an alternative method of solution for two-dimensional elastohydrodynamically lubricated point contact calculations

ASME J. Tribol., 1987, 109, 437–443.

Venner

C. H.

Multilevel solution of the EHL line and point contact problems. PhD Thesis, University of Twente, Enschede, The Netherlands, ISBN 90-9003974-0, 1991.

Venner

C. H.

Lubrecht

A. A.

Multilevel Methods in Lubrication (Ed. Dowson

) Elsevier Tribology Series, Vol. 37, Elsevier, ISBN 0-444-50503-2, 2000.

10.

Zhu

Hartl

Krupka

A comparative study on the EHL film thickness results from numerical solutions and experimental measurements. Presented at 2004 STLE Annual Meeting, Toronto, Canada.

11.

Hamrock

B. J.

Dowson

Isothermal elastohydrodynamic lubrication of point contacts, Part III fully flooded results

ASME J. Lub. Technol., 1977, 99, 264–276.

12.

Roelands

C. J. A.

Correlational aspects of the viscosity temperature pressure relationship of lubricating oils. PhD Thesis, Technical University, Delft, The Netherlands (VRB Groningen, The Netherlands), 1966.

13.

Dowson

Higginson

G. R.

Elastohydrodynamic Lubrication, The Fundamentals of Roller and Gear Lubrication, 1966, (Pergamon Press, Oxford, UK).

14.

Y. Z.

Zhu

A full numerical solution to the mixed lubrication in point contacts

ASME J. Tribol., 2000, 122, 1–9.