Non-isothermal and electrochemical modelling of the multi-cell module performance in the integrated-planar solid oxide fuel cell

Abstract

This article presents a performance analysis of a multi-cell integrated-planar solid oxide fuel cell (IP-SOFC) fuelled by pure hydrogen. A non-isothermal electrochemical model, taking into account the temperature variation produced by electrochemical reactions, air, and fuel flow, is used to predict the characteristics of the multi-cell module. The model results show good agreement with the experimental data obtained from a full-size IP-SOFC module prototype for both a first- and a second-generation hybrid application. In this study, a simulation model of individual cell voltage loss indicates that ohmic and activation losses dominate the performance. Sensitivity analyses of the multi-cell show that decreasing the electrolyte thickness can improve cell performance. An increase in operating temperature causes a decrease in ohmic loss and ameliorates the voltage and power cell. Further, increasing the operating pressure produces a weak increase in cell performance.

Keywords

integrated-planar solid oxide fuel cell non-isothermal modelling electrochemical reactions gas flow cell performances

Get full access to this article

View all access options for this article.

References

Gardner

F. J.

Day

M. J.

Brandon

N. P.

Pashley

M. N.

Cassidy

, ‘SOFC technology development at Rolls-Royce’ J. Power Sources 86 (2000): 122–129.

Jung

H. Y.

Choi

S. H.

Kim

Son

J.-W.

Kim

Lee

H.-W.

Lee

J. H.

, ‘Fabrication and performance evaluation of 3-cell SOFC stack based on planar 10 cm×10 cm anode-supported cells’ J. Power Sources 159 11 (2006): 478–483.

Vinod

M. J.

Olaf

, ‘Numerical study of mass and heat transport in solid-oxide fuel cells running on humidified methane’ Chem. Engng Sci. 62 (2007): 5473–5486.

Larrain

Favrat

Maréchal

Van

H. J.

, ‘Generalized model of planar SOFC repeat element for design optimization’ J. Power Sources 131 1–2 (2004): 304–312.

Daun

K. J.

Beale

S. B.

Liu

C. H.

Smallwood

G. J.

, ‘Radiation heat transfer in planar SOFC electrolytes’ J. Power Sources 157 (2006): 302–310.

Fontell

Kivisaari

Christiansen

Hansen

J. B.

Pålsson

, ‘Conceptual study of a 250kW planar SOFC system for CHP application’ J. Power Sources 131 1–2 (2004): 49–56.

Yakabe

H. L.

Ogiwara

Hishinuma

Yasuda

, ‘3-D model calculation for planar SOFC’ J. Power Sources 102 11 (2001): 144–154.

Jones

, ‘Pressurisation of IP-SOFC technology for second generation hybrid application’ (Ansty, UK: Rolls-Royce Fuel Cell Systems Limited 2005) Project F/01/ 00278/REP.

Costamagna

Honegger

, ‘Modeling of solid oxide heat exchanger integrated stacks and simulation at high fuel utilization’ J. Electrochem. Soc. 145 (1998): 3995–4007.

10.

Haberman

B. A.

Young

J. B.

, ‘Three-dimensional simulation of chemically reacting gas flows in the porous support structure of an integrated-planar solid oxide fuel’ Int. J. Heat Mass Transf. 47 (2004): 3617–3629.

11.

Haberman

B. A.

Young

J. B.

, ‘Numerical investigation of the air flow through a bundle of IP-SOFC modules’ Int. J. Heat Mass Transf. 48 (2005): 5475–5487.

12.

Hall

D. J.

Colclaser

R. G.

, ‘Transient modeling and simulation of a tubular solid oxide fuel cell’ IEEE Trans. Energy Convers. 14 (1999): 749–753.

13.

Mounir

Elgharad

Belaiche

Boukalouch

, ‘Numerical simulation of heat and mass transfer in an IP-SOFC fuel cell’ In 5éme Journée International des Études Techniques, Marrakech, Maroc, 2008.

14.

Suwanwarangkul

Croiset

Fowler

M. W.

Douglas

P. L.

Entchev

Douglas

M. A.

, ‘Performance comparison of Fick's, dusty-gas and Stefan—Maxwell models to predict the concentration overpotential of a SOFC anode’ J. Power Sources 122 (2003): 9–18.

15.

Mills

A. F.

, Basic heat and mass transfer (Irwin Heat Transfer Series) (Chicago: Irwin 1995).

16.

Inui

Suto

Murata

, ‘Numerical simulation of basic electrical and thermal characteristics of planar solid oxide fuel cell’ IEEJ Trans. Power Energy 123 (2003): 68–75.

17.

Chase

M. W.

Daies

C. A.

Downey

J. R.

Frurip

D. J.

McDonald

R. A.

Syverud

A. N.

, JANAF thermochemical tables 14 (New York: Pergamon Press 1985).

18.

Larminie

Dicks

, Fuel cell systems explained (West Sussex, England: Wiley 2003).

19.

Leung

M. K. H.

Leung

D. Y. C.

, ‘Parametric study of solid oxide fuel cell performance’ Energy Convers. Manage. 48 (2007): 1525–1535.

20.

Aguiar

Adjiman

C. S.

Brandon

N. P.

, ‘Anode supported intermediate temperature direct internal reforming solid oxide fuel cell, I: Model based study state performance’ J. Power Sources 138 (2004): 120–136.

21.

Bossel

U. G.

, ‘Facts and figures’ (1992) Final Report on SOFC data, IEA report, Operating Task II Swiss Federal Office of Energy, Berne, CH, 1992.

22.

Kee

Coltrin

Glarborg

, Chemically reacting flow: Theory practice (New York: Wiley 2003).

23.

Mounir

Elgharad

Belaiche

Boukalouch

, ‘Numerical modeling of temperature distribution and the effect on IP-SOFC fuel cell performance’ In 9ièmes Journées d'Analyse Numérique et, JANO9 Conference, Mohammedia, Maroc, 20 November 2008.

24.

Denton

J. D.

, ‘The calculation of three-dimensional viscous flow through multistage turbomachines’ ASME J. Turbomach. 114 (1992): 18–26.